Legacy Car Audio Cassette Player LR 203FX User Manual

LEGACY

LR-203FX

INSTRUCTION MANUAL

PLL QUARTZ TUNING ELECTRONIC AUDIO CONTROL

STEREO CAR RADIO CASSETTE PLAYER

PRECAUTIONS AND MAINTENANCE

8. BAND BUTTON

Press it to select you desired radio band and the word which band is selected

will be indicated on LCD.

.1.This unit is designed for negative ground operation only. The equipment can

be used safely, if the negative terminal of the battery is connected to the

vehicle metal work.

2.Do not use speakers of impedance less than 4 ohms; and allow the speaker

wires to be shorted together when the unit is switched on.

9. SEEK BUTTON

Press it to auto seek up frequency until find the desired broadcast.

Otherwise it may overload or burn out the power amplifier stage.

3.If the car interior is extremely hot, as after being parked in the sun, do not use

the player until the car has been driven for a while to cool off the interior.

4.Take care of your tape cassette to preserve the quality of the recordings. Do

not allow them to be exposed to direct sunlight. Store them in a place

protected from dirt and dust and avoid handing with greasy or oily hands.

Also, keep the away from magnets, and motors of the permanent magnet type.

5.It is not advisable to use cassette tapes longer than C-60(30 minutes per side)

in automobile players, since the tape is too thin and tends to become easily

entangled. Always remove cartridge from your tape player as soon as play is

finished.

6.The capstan and tape head should be cleaned about once every six months

with a soft cloth or cotton-wool swab, moistened with alcohol.

This will serve to maintain the richness and clarity of sound, and prevent loss

of volume. Do not use a screwdriver, or ferrous metal rod , in carrying out the

above cleaning. See illustration.

10. AS/PS BUTTON

Press it to perform all stations memory for 5seconds each time.while memory

digital and frequency will flash on LCD.If thebutton is pressed for more than2

seconds,it will seek station on current band,Then write to the preset memories

and word ART willappear on :LCD.When the auto-storage operation is

completed, it will automatically perform for 5seconds each time.During the

memory station performing,press 1-6digital buttons to select and stop

scanning function.

11. STEREO/MONO BUTTON

Press it to change the sound effect.( Mono keep remain)

12. FREQUENCY/CLOCK SWITCH

Press this button to select the display mode such as frequency display or clock

display.(you can only adjust tine setting at clock display)

13. CD SWITCH

14. LOUDNESS BUTTON

press it to get the best loudness quality during it is for bass.And word LOUD

will appear on LCD.

7.A loosely wound cassette tape will get damaged. Prior to using such tape,

tighten it in a manner as guided by Fig. 2.A carelessly would cassette tape will

cause unnecessary pressure on the tape resulting in the cassette springing out

while the tape is running .For prevention, rewind the tape through fast for

warding or rewinding.

15. 1-6 PRESET BUTTONS

Press them to recall all storage station frequency which will appear on LCD,

stations can be memorized in band.

16. CD INPUT JACK

17. RET BUTTON

Press it to reset the functions when programms are disorder.

WIRING CONNECTION

INSTALLATION

PRECAUTIONS

ANTENNA PLUG

PINK

1. Choose the mounting location carefully so that the unit will not interfere with the

normal driving functions of the driver.

MEMORY B+

FUSED

FILTER

BOX

RED R

RCA LINE OUT

2. Avoid installing the unit where it would be subject to high temperatures, such as

from direct sunlight or hot air from the heater, or where it would be subject to

dust, dirt or excessive vibration.

BLACK(GND)

RED (B+)

WHITE L

0.5A &7A

FUSES

YELLOW AUTO ANT

3. Use only the supplied mounting hardware for a safe and secure installation.

FRONT

BROWN

GREY

LEFT

RIGHT

GREY/WHITE

GREEN

BROWN/WHITE

BLUE

REAR

GREEN/WHITE

BLUE/WHITE