CAT5 SWITCHER
KE811CT(w-type)
Instruction Manual
Thank you for your purchase of this product
Please be sure to read this manual completely prior to usage of this product.
Ver 1.0E
Usage Cautions
Please be sure to read this manual prior to usage of product. After reading, keep it in
a place near the equipment where it can be easily referred to.
・If this symbol is ignored death or serious injury may
Warning
Caution
occur.
・If this symbol is ignored injury or property damage may
occur.
Explanation of symbols
●Shows caution
●Shows an action that should be done.
(including warning)
General caution
Keep hands clear
General indication
Unplug the power cord
●Shows an action that should not be done.
Prohibited Do not expose
to water
Do not use in
a wet place
Do not attempt Do not touch
to take apart
Do not touch
with wet hands
● We are not responsible for damages to an image or sound transmitted by
our product caused by the products malfunction or any other outside factor.
Warning
◆Do not continue to use this product if any of the following occurs :
※It may cause fire or electric shock.
・If you smell a strange odor or smoke.
・If water or a foreign object gets inside the product.
・After dropping the product.
・If the power cord is damaged. (exposure of core cable, severed cable)
◆If any of the above should occur immediately turn the power off and
unplug the power cord. Contact the manufacturer or dealer who installed
this product for repair.
◆Do not place on an unsteady surface.
※Do not place on a sloped or unstable surface.
It can cause serious injuries.
◆Do not attempt to repair the product by yourself under any
circumstances.
◆Do not use this product except for the specified
voltage and current (AC100～240V).
※May cause fire or electric shock.
◆Do not stick any foreign objects into the product.
※May cause fire or electric shock.
◆Do not allow the product to get wet.
※May cause fire or electric shock.
◆Do not touch the power cord during a thunder storm.
※May cause electric shock.
◆Plug the product into an outlet that can be easily reached.
※Unplug the product if trouble occurs.
◆Be sure to completely insert the power cord plug into the outlet.
※Short circuiting or the generation of heat may cause fire or electric
shock. Do not connect many cords into one outlet.
◆Do not damage the power cord.
※May cause fire or electric shock.
・Do not modify the power cord.
・Do not pull or bend the power cord.
・Do not place a heavy object or this product on the cord.
・Do not place the power cord close to a source of heat.
Caution
◆Do not put this product in the following places.
※May cause fire or electric shock.
・Places where there is a lot of humidity or dust.
・Places where there is steam.
・Near places which generate heat.
・Places where water may come into contact with the product.
◆Turn off the power and follow all instructions ,
when connecting this product to other devices.
※Failure to use the recommended cables may cause generation of heat or fire.
◆Do not cover the ventilation holes.
※Doing so may cause the product to overheat, which can cause
fire or damage to the product.
・Do not leave the product laying on its side or turn it upside down.
※Do not cover the ventilation holes or stick foreign objects
into this product as it will cause damage.
◆Disconnect all cables before moving this product.
※The cables can be damaged and fire or electric shock may occur if
not disconnected.
◆Do not place a heavy object on this product.
※Placing a heavy or oversized object on the product may
cause injury as a result of it falling.
◆Disconnect the power cord when the product will not be used
for a long time.
※Disconnect the power cord for safety purposes and to lower energy
consumption.
◆Unplug the product when servicing.
※Electric shock can occur even though the product is turned off
as current is still flowing from the power cord.
◆Do not unplug the device by pulling on the power cord.
※Pulling on the power cord may damage the cord or cause a fire or electric shock.
Please pull on the plug body.
◆Do not disconnect or connect the power plug with wet hands.
※May cause electric shock.
Index
1. About this product
1
1-1. Product and accessories
1-2. General information
1
2
3
3
5
ach parts
2. The name and function of e
2-1. Front panel
2-2. Rear panel
3. Connection
7
3-1. The cautions and warnings
7
8
3-2. Preparation of a cable
3-3. Cable mounting kit and rack mounting kit
9
3-4. How to connect
10
4. Operation
12
12
4-1. The setting of front dip switch
4-2. The setting of bottom dip switch
4-3. Operation of buttons
13
14
15
15
16
17
5. Serial interface
5-1. The setting of personal computer
5-2. Connection of RS232C cable
5-3. Control and registration method
5-3-1. Control method
17
21
5-3-2. Registration method
6. Parallel interface
22
23
23
24
24
25
26
7. Specifications
7-1. The specifications of this product
7-2. The specifications of control system connectors
7-2-1. Connectors for power control and option button output
7-2-2. Connector for tally output
7-2-3. Connector for parallel input
8. Trouble shooting
27
1.About this product (KE811CT(w-type))
1-1. Product and accessories
Please check that you have the accesories and items shown.
CAT5 OUT
KE811CT
INPUT
5
OPTION
SERIAL 3
RGB IN8
AUDIO IN8
OFF
A
B
C
D
E
F
2
3
4
6
7
8
1
DISPLAY
POWER
POWER
CONT
4
1
SUB OUT
Main unit of KE811CT(w-type)
Cable mounting kit
AC adapter
Power cord
Rack mounting kit ×2
Screw×4
Screw×4
Fixing bands×2
Terminal 6-pin×2
Terminal 2-pin×2
CAT5 SWITCHER
KE811CT(w-type)
Instruction Manual
Thank you for your purchase of this product
Please be sure to read this manual completely prior to usage of product
Ver 1.0E
Instruction Manual
(This booklet)
-1-
1-2 General Information
This product, KE811CT(w-type), is a transmitter for long distance transmission of one line selected
from RGB video, component video or composite video through a twisted pair cable (CAT5e or CAT6).
In addition to video , one line of audio (stereo) , and serial command (*1) can be transmitted through
a serial port.
By INPUT switch, it is possible to control PDP or projector at the same time as switching of
video and audio .
(*1) Beforehand registered serial command is transmitted.
The minimum recommended transmission distance is 10m(32.8ft). The maximum recommended
transmission distance depends on the refresh rate and resolution. The transmission distance
(when using our recommended cable) is as follows.
Name of signal
Audio signal/serial data
Composite signal
YPbPr／YCbCr
640×480
800×600
1024×768
Transmission distance
：10～300m(32.8～984.2ft)
：10～300m(32.8～984.2ft)
：10～300m(32.8～984.2ft)
：10～200m(32.8～656.1ft)
：10～180m(32.8～590.5ft)
：10～150m(32.8～492.1ft)
：10～120m(32.8～393.7ft)
：10～100m(32.8～328ft)
1280×1024
1600×1200
Recommended cable : OKTP-E5-P-AWG24x4P
(OKANO ELECTRIC WIRE CO.,LTD)
The features of this product are below mentioned.
・Transmitting one line for twisted pair (2 distributed outputs) and one line for monitor
independently selected from video (three composite and one component signals) 4 inputs
and RGB 4 inputs.
Audio and command are transmitted at the same time.
・Beforehand registered (*2) command can be transmitted by pressing of INPUT buttons.
・Command transmission may be allocated to DISPLAY POWER, OPTION and INPUT buttons.
・Screen etc.. can be controlled by contact output in conjunction with OPTION button selecting.
・Tally output of rear panel is transmitted synchronizing with buttons.
・This product can be controlled by serial communication and parallel input.
(*2) Exclusive software is required to register commands.
-2-
2．The name and function of each parts
2-1. Front panel
22
⑨
CAT5 OUT
KE811CT
OPTION
INPUT
5
SERIAL 3
RGB IN8
AUDIO IN8
OFF
A
B
C
D
E
F
2
3
4
6
7
8
1
DISPLAY
POWER
POWER
CONT
4
1
SUB OUT
⑩
⑧
①
②
③
④
⑤ ⑥ ⑦
⑭
⑪
① POWER CONT button
This button controls external power. When this button is pushed,the signal (photo MOS relay
make contact)is output from connector for POWER CONT. (This button is not for the product.)
This button can be synchronized DISPLAY POWER button.
At synchronization mode, DISPLAY POWER buttons of CAT5 OUT, SUB OUT are ON when
POWER CONT button is ON.
(Please refer to "4-2. The setting of bottom dip switch.")
② DISPLAY POWER button
This button control the power of equipments connected to CAT5 OUT and SUB OUT
(SERIAL 2) of rear panel. (Beforehand serial command should be registered.)
CAT5 OUT and SUB OUT(SERIAL 2) can be controlled independently.
Command is transmitted to SUB OUT(SERIAL 2) when DISPLAY POWER button is pressed
after pressing SUB OUT button.
Command is transmitted to CAT5 OUT when DISPLAY POWER button is pressed after
pressing CAT5 OUT button.
③ OPTION button
When this button is pushed, the signal (photo MOS relay make contact)is output from
connectors for OPTION A-F .Output can be selected momentarily or alternately.
The equipments connected to CAT5 OUT and SUB OUT(SERIAL 2) of rear panel can be
controlled in command. (Please refer to "4-2. The setting of bottom dip switch.")
Command is submitted to both of CAT5 OUT and SUB OUT(SERIAL 2).
④ INPUT button
Video and audio which are transmitted to CAT5 OUTor SUB OUTcan be selected.
button 1-3 are for composite video, button 4 is for component video, button 5-8 are for
RGB video.
CAT5 OUT and SUB OUT can transmit a video, a audio, and a command separately.
Video, audio and command are transmitted to SUB OUT when INPUT 1-8 buttons are pressed
after pressing SUB OUT button.
Video, audio and command are transmitted to CAT5 OUT when INPUT 1-8 buttons are pressed
after pressing CAT5 OUT button.
⑤ OFF button
Output of video and audio become OFF. Press again to release or press INPUT button to
release.
⑥ SUB_OUT button
SUB output is selected.
-3-
⑦ CAT5_OUT button
CAT5 output is selected.
⑧Front Dip Switch
Please refer to "4-1. The setting of front dip switch."
⑨SERIAL_3
DB9 connector for serial communication.
This connector is used to register commands into the product.
(Please refer to "5-2 Connection of RS232C cable.")
⑩Front LED
Yellow LED : It does not light.
Green LED : It lights when command mode is ON.
Orange LED : It lights when SERIAL1&3 are transmitting or receiving.
⑪Bottom dip switch
Option setting is available,etc...
(Please refer to "4-2. The setting of bottom dip switch.")
-4-
2-2．Rear panel
22
23
21
24
25
26
SERIAL 1
SERIAL 2
3
4
2
5
1
6
7
AUDIO SUB OUT
4
CAT5 OUT1
CAT5 OUT2
AUDIO IN
PARALLEL REMOTE
FG
DC16V IN
3
2
5
6
7
1
POWER
CONT
OPTION OUT
COMPOSITE
SUB OUT
RGB IN
COMPOSITE IN
COMPONENT IN
RGB SUB OUT
E
F
B
C
D
A
⑫
⑬
⑭
⑮
⑯
⑰
⑱
⑲ ⑳
⑫ COMPOSITE IN 1-3
RCA connector, video input connectors.
Input connectors for composite video.
These connectors are corresponding to INPUT 1-3 at front panel.
※Please use a cable under 3m(9.84feet) in length when connecting.
⑬ COMPOSITE SUB OUT
RCA connector, video output connector for SUB OUT.
The video inputs into COMPOSITE IN can be transmitted to SUB .
※Please use a cable under 3m(9.84feet) in length when connecting.
⑭ RGB IN 5-8
15pin HD female, video input connector.
For RGB video input connector (not for GonSYNC).
RGB IN 8 is located at front panel ⑭.
These connectors are corresponding to INPUT 5-8 on front panel.
※Please use a cable under 3m(9.84feet) in length when connecting.
⑮ COMPONENT IN 4
RCA connector, video input connector for SUB OUT.
For component video input connector.
These connectors are corresponding to INPUT 4 on front panel.
※Please use a cable under 3m(9.84feet) in length when connecting.
⑯ RGB_SUB_OUT
15pin HD female, video output connector for SUB OUT.
The video input to RGB IN or COMPONENT IN can be transmitted to SUB.
※Please use a cable under 3m(9.84feet) in length when connecting.
⑰ CAT5_OUT1，CAT5_OUT2
RJ-45 twisted pair connector for CAT5 OUT.
The video input to COMPOSITE IN, RGB IN or COMPONENT IN can be transmitted
to CAT5.
CAT5e or CAT6 cable connected between this connector and CAT5 receiver.
2 outputs are available.
◆Warning
Do not connect the receiver which is not recommended.
⑱ OPTION OUT A-F, POWER CONT
Terminal connector for OPTION and POWER CONT.
These outputs are corresponding to POWER CONT, OPTION A-F at front panel.
Output is relay (MOS output).
-5-
⑲ DC16V_IN
Connecter for power input.
DC16V AC adapter is connected.
◆Warning
The enclosed AC adapter must be used for this product.
⑳ FG
The screw for frame ground.
21
AUDIO IN 1-4
RCA connector for audio input connector.
These connectors are audio input connector.
These connectors are corresponding to INPUT 1-4 at front panel.
※Please use a cable under 3m(9.84feet) in length when connecting.
22
AUDIO IN 5-8
Mini-jack for audio input.
These connectors are for audio input.
AUDIO IN 8 is located of front panel
22
.
These connectors are corresponding to INPUT 5-8.
※Please use a cable under 3m(9.84feet) in length when connecting.
23
AUDIO SUB OUT
RCA connector , audio output for SUB OUT.
These connectors are for audio output.
The audio output into AUDIO IN can be transmitted to SUB .
※Please use a cable under 3m(9.84feet) in length when connecting.
24
SERIAL 1
DB9 connector for serial communication.
Serial communication is available.
Through this connector, the product can be controlled.
Straight cable is needed when this product is connected Personal Computer.
(Please refer to "5-2 Connection of RS232C cable.")
25
SERIAL 2
DB9 connector for serial communication.
Commands, which were beforehand registered, can be transmitted.
(Please refer to "5-2 Connection of RS232C cable.")
26
PARALLEL REMOTE
Ribbon connector, 50pin.
This product can be controlled by contact input.
Input-pin is non-voltage contact.
Output-pin is open-collector.
-6-
3. Connection
3-1.The cautions and warnings
◆Cautions
・Use the recommended a twisted-pair cable for this product for best results.
(OKANO ELECTRIC WIRE CO.,LTD: OKTP-E5-P-AWG 24x4P)
When a cable other than the recommended cable is used, make sure that the characterisitcs
and functionality of the cable is fully understood before use.
・When cable length is longer than the recommendation distance indicated in the
"1-2 General information", quality of the image may deteriorate.Please note that use beyond
the recommended distance will require outside support.
・If a twisted-pair cable is laid near a power supply line with a lot of noise,
the image may flicker. In this case, run the twisted-pair cable away from the power supply
line.
・If this product is connected to an AC power supply with noise, the image may flicker.
In this case, use an AC wall socket type noise filter.
・Use the cable mounting kits, when undesirable force will be applied to the twisted pair
connectors of this product. (Please refer to "3-3. Cable mounting kit,Rack mounting kit.")
◆Warnings
・Do not connect any unauthorized product to the extension input/output connectors of this
product or twisted pair receiver, as it can cause damage to this product or twisted pair receiver.
Kowa is not responsible for any damage or injury caused as a result of improper use.
・Turn off this product, receiver, and any products that is connected to the devices when
removing or installing twisted pair cables. Failure to do so can cause damage or failure
of the products.
-7-
3-2.Preparation of a cable
A CAT5e or CAT6 cable is used to connect this product and twisted pair receiver.
This product and receiver are connected straight through as shown in the diagram below.
※ Please keep the combination of the pair lines as follows. If the combination of a pair line
is incorrectly installed , there is a possibility that the quality of the image may deteriorate.
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1,2…pair 1
3,6…pair 2
4,5…pair 3
7,8…pair 4
Cables
Connector
Connector
-8-
3-3. Cable mounting kit and rack mounting kit
A mounting kit for the twisted-pair cable is enclosed with this product.
Use the following diagram to attach the mounting kit.
Diagram for attachment
Cable mounting kit
T U O B U S
E T I S O P M O C
F
E
D
C
B
A
T U O B U S B G R
N I T N E N O P M O C
N I B G R
N I E T I S O P M O C
T N O C
R E W O P
T U O N O I T P O
1
N I V 6 1 C D
7
6
5
3
2
Cable mounting kit
E T O M E R L E L L A R A P
G F
2 T U O 5 T A C
1 T U O 5 T A C
T U O B U S O I D U A
N I O I D U A
7
6
5
4
3
2
1
2
L A I R E S
1
L A I R E S
Cable mounting kit
CAT5 OUT
KE811CT
INPUT
OPTION
SERIAL
3
AUDIO IN8
OFF
A
B
C
D
E
F
2
3
4
5
6
7
8
DISPLAY
POWER
1
POWER
CONT
4
1
RGB IN8
SUB OUT
Rack mounting kit
Rack mounting kit
◆Cautions
・The temperature inside the rack must not exceed 40℃.
・Secure the rack mounting kits to this product and the rack using the supplied screws.
・Loads other than this product must not weight on the rack mounting kits.
・The power cord and AC adapter must be used in the rating.
-9-
3-4. How to connect
Connect this product according to the following procedures.
Ⅰ．Check that all of the devices ,PDP(Plasma Display Panel), video player, DVD player,
PC, display, and so on, to connect are turned off.
22
⑨
Ⅱ. Refer to the following diagrams when connecting cables to this product.
CAT5 OUT
KE811CT
INPUT
5
OPTION
SERIAL 3
RGB IN8
AUDIO IN8
OFF
A
B
C
D
E
F
2
3
4
6
7
8
1
DISPLAY
POWER
POWER
CONT
4
1
SUB OUT
⑩
⑧
①
②
③
④
⑤ ⑥ ⑦
⑭
⑪
22
23
21
24
25
26
SERIAL 1
SERIAL 2
3
4
2
5
1
6
7
AUDIO SUB OUT
4
CAT5 OUT1
CAT5 OUT2
AUDIO IN
PARALLEL REMOTE
OPTION OUT
FG
DC16V IN
3
2
5
6
7
1
POWER
CONT
COMPOSITE
SUB OUT
RGB IN
COMPOSITE IN
COMPONENT IN
RGB SUB OUT
E
F
B
C
D
A
⑫
⑬
⑭
⑮
⑯
⑰
⑱
⑲ ⑳
a)．Composite video
Connector⑫
Input of composite
Connector⑬
Output of composite(for SUB OUT）
3
1
2
COMPOSITE
SUB OUT
COMPOSITE IN
b)．Component video
Connector⑮
Connector⑯
Pr input Y input Pb input
Output of component (for SUB OUT）
RGB SUB OUT
COMPONENT IN
c)．RGB video
5
6
7
8（Front panel）
RGB IN
RGB SUB OUT
Input of RGB
Connector⑭
Output of RGB(for SUB OUT)
Connector⑯
-10-
d)．Audio
5
6
7
8（Front panel）
3
4
2
1
AUDIO IN
AUDIO SUB OUT
Mini-jack for audio input
Connector 22
input input
input input
input input
input input
output output
L
R
L
R
L
R
L
R
L
R
Audio output
23
21
Connector
Connector
(for SUB OUT)
Ⅲ．As for connection of cables going to twisted pair receiver, please refer to the manual
of twisted pair receiver.
Ⅳ．Connect between this product and twisted pair receiver by using CAT5e or CAT6 cable.
(Please refer to "3-2 Preparation of cable.")
Ⅴ．Fix the CAT5e or CAT6 cable by cable mounting kit.
(Please refer to "3-3. Cable mounting kit, rack mounting kit.")
◆Warnings
Turn on the each equipment according to below mentioned.
・First connect AC adapter to this product.
・Next, turn on twisted pair receiver.
As for operation and adjustment, please refer to "4.Operation."
-11-
4. Operation
4-1. The setting of front dip switch
ON
GH
1
2
3
4
NO.
1
2
3
4
ON ：Registration mode (Regardless of the setting of No.2-4.)
OFF：Standard mode
no working
ON ：POWER CONT becomes ON, when AC adapter is connected to outlet.
OFF：POWER CONT becomes ON, when POWER CONT is pressed.
no working
※All switches of front dip switch are set at OFF as initial setting.
-12-
4-2. The setting of bottom dip switch
1
2
3
4
5
6
7
8
OFF
NO.
1
ON ：OPTION A button, momentary
OFF：OPTION A button, alternate
2
3
4
5
6
7
ON ：OPTION B button, momentary
OFF：OPTION B button, alternate
ON ：OPTION C button, momentary
OFF：OPTION C button, alternate
ON ：OPTION D button, momentary
OFF：OPTION D button, alternate
ON ：OPTION E button, momentary
OFF：OPTION E button, alternate
ON ：OPTION F button, momentary
OFF：OPTION F button, alternate
ON ：POWER CONT button, DIPLAY POWER button,
synchronization mode
OFF : un-synchronization
8
no working
※All switches of bottom dip switch are set at OFF as initial setting.
-13-
4-3. Operation of buttons
a) POWER CONT button
It can control the power in the rack. The operation of others buttons can be controlled
(become ON), when this button is pressed.
When NO.7 of bottom dip switch is ON, DISPLAY POWER button synchronizes and becomes ON.
(Please refer to "4-2. The setting of bottom dip switch.")
When POWER CONT button is OFF, all buttons are OFF (It is not related to a setup of a switch).
※ This button is not for this product, this product is ON when AC adapter is connected.
b) DISPLAY POWER button (command transmission button)
According to ON/OFF , command to notice power ON/OFF is transmitted to CAT5 or SUB(SELIAL 2)
and the connected equipments can be ON/OFF.
(ON/OFF serial command for the connected equipments shall be registered beforehand.)
The command to notice the other information can be transmitted to CAT5, SUB(SERIAL 2)
by registration.
The command is transmitted to SUB (SERIAL 2), when DISPLAY POWER button is pressed
after pressing SUB OUT button.
The command is transmitted to CAT5, when DISPLAY POWER buttons is pressed after
pressing CAT5 OUT button.
c) OPTION button (command transmission button)
It can control the curtain or screen etc... with relay of rear panel.
The setting alternate/momentary is available with bottom dip switch.
(Please refer to "4-2. The setting of bottom dip switch.")
The command can be transmitted to both of CAT5 and SUB (SERIAL 2).
If the command would not be transmitted to CAT5, do not register any command in CAT5.
If the command would not be transmitted to both of CAT5 and SUB (SERIAL 2), do not register
any command in CAT5 and SUB (SERIAL 2).
If the command would not be transmitted to SUB,do not register any command in SUB.
d) INPUT 1-8
One line from IN1-3 (composite), IN4 (component), IN5-8 (RGB), can be transmitted to CAT5
and SUB separately.
Command (which shall be registered beforehand) can be transmitted to CAT5 or SUB (SERIAL 2),
when the button is pressed.
The video, audio and command are transmitted to SUB, when one of INPUT 1-8 after pressing
SUB OUT button.
The video, audio and command are transmitted to CAT5, when one of INPUT 1-8 after pressing
CAT5 OUT button.
e) OFF button
Stopping transmission of video and audio.
To stop CAT5 output, press OFF button (is illuminated) after pressing CAT5 OUT button.
To release, press again (button is not illuminated) or press INPUT button.
f) CAT5 OUT button
Press this button to select CAT5 output (button is illuminated.).
g) SUB OUT button
Press this button to select SUB output (button is illuminated.).
-14-
5. Serial interface
5-1. The setting of personal computer
Set the personal computer as follows, when this product is controlled.
Baud rate
Data bits
Stop bits
Parity bits
: 9600bps
: 8
: 1
: none
Handshaking : none
Communication method : full duplex
-15-
5-2. Connection of RS232C cable
Serial 1 & 3 Pin-Out Diagram
Pin1 Non connect (NC)
Pin2 Transmitted (TX)
Pin3 Received Data (RD)
Pin4 DTE ready connected with Pin6.
Pin5 GND
Pin6 DCE ready
Pin7 Request to send (RTS)
Pin8 Clear to send (CTS)
Pin9 Non connect (NC)
Serial 2 Pin-Out Diagram
Pin1 Non connect (NC)
Pin2 Received Data (RD)
Pin3 Transmitted Data (TD)
Pin4 DTE.
Pin5 GND
Pin6 It connects with Pin4.
Pin7 It connects with Pin8.
Pin8 It connects with Pin7.
Pin9 Non connect (NC)
Pin Number
1
2
3
4
5
6
7
8
9
-16-
5-3. Control and registration method
5-3-1. Control method
Control method code table (video audio synchronization)
Command
IN１
Character
ASCII
４１Ｈ
４２Ｈ
４３Ｈ
４４Ｈ
４５Ｈ
４６Ｈ
４７Ｈ
４８Ｈ
４９Ｈ
４ＡＨ
４ＢＨ
４ＣＨ
４ＤＨ
４ＥＨ
４ＦＨ
５０Ｈ
５１Ｈ
５２Ｈ
３１Ｈ
３２Ｈ
３３Ｈ
３４Ｈ
３５Ｈ
３６Ｈ
３７Ｈ
３８Ｈ
５７Ｈ
note
Ａ
Ｂ
Ｃ
Ｄ
Ｅ
Ｆ
Ｇ
Ｈ
Ｉ
IN２
IN３
IN４
IN５
IN６
IN７
IN８
DISPLAY_POWER
POWER_CONT
OPTION_A
OPTION_B
OPTION_C
OPTION_D
OPTION_E
OPTION_F
IN_OFF
Ｊ
Ｋ
Ｌ
Ｍ
Ｎ
Ｏ
Ｐ
Ｑ
Ｒ
1
IN_ON
ＣＡＴ５
Remark 1
ＳＵＢ
2
Remark 1
Remark 2
Remark 2
Remark 3
Remark 4
Remark 5
Remark 6
ＯＮ
3
ＯＦＦ
4
ＣＡＴ５，ＯＮ
ＣＡＴ５，ＯＦＦ
ＳＵＢ，ＯＮ
ＳＵＢ，ＯＦＦ
Reading data
5
6
7
8
Ｗ
，
；
Pause
Semicolon
Return
ACK
２ＣＨ
３ＢＨ
０ＤＨ
０６Ｈ
Remark 7
Remark 8
Remark 8
１５Ｈ
NAK
Remark 1 : This character is used to select output.
Remark 2 : This character is used when POWER CONT, OPTION are ON/OFF.
Remark 3 : This character is used to select output (CAT5) when DISPLAY POWER is ON.
Remark 4 : This character is used to select output (CAT5) when DISPLAY POWER is OFF.
Remark 5 : This character is used to select output (SUB) when DISPLAY POWER is ON.
Remark 6 : This character is used to select output (SUB) when DISPLAY POWER is OFF.
Remark 7 : no character Only ASCII code , not described by character.
Remark 8 : "ACK" is answer backing. When this product was able to receive the command,
it returns "ACK."
"NAK" is answer backing. When this product was not able to receive the command,
it returns "NAK."
-17-
※When OPTION button is used as alternate, control command can transmit ON/OFF
registration command. When OPTION button is used as momentary, control command
can transmit ON registration command only.
※Memory size of control command is 32bytes (8 commands). The data length that can be sent
at a time is 32bytes.
If more than 32bytes data is transmitted, please send the data after answer-back is
returned.
If control command is transmitted before answer-back is returned, it may not be executed.
※During serial communication, the operation of button may not be valid.
-18-
a) When controlling this product by sending one control command.
This product can be controlled.
Please send control command in the following order.
1. Character (input line or action select command).
2. Delimiter.
3. Character (output line select command).
4. Return.
※Set the front dip switch to Registration mode.
Please refer to "4-1 The setting of front dip switch."
(Ex.1) input : IN2, output : CAT5
ASCII character representation
HEX representation
B
,
1
return
42H 2CH 31H 0DH
(Ex.2) input : IN6, output : SUB
ASCII character representation
HEX representation
F
,
2
return
46H 2CH 32H 0DH
(Ex.3) Turning OFF of CAT5OUT.
ASCII character representation
HEX representation
Q
,
1
return
51H 2CH 31H 0DH
(Ex.4) Turning OFF of SUBOUT.
ASCII character representation
HEX representation
Q
,
2
return
51H 2CH 32H 0DH
(Ex.5) Turning ON of POWER CONT.
ASCII character representation
HEX representation
J
,
3
return
4AH 2CH 33H 0DH
(Ex.6) Turing OFF of DISPLAY POWER (switching to CAT5 OUT).
ASCII character representation
HEX representation
I
,
6
return
49H 2CH 36H 0DH
(Ex.7) Turing ON of OPTION B.
ASCII character representation
HEX representation
L
,
3
return
4CH 2CH 33H 0DH
※ This product sends, ACK (06H), as answer-back when operation of one control command
is executed.
This product sends, NAK (15H), as answer-back when operation of one control command
is not executed.
-19-
b) When controlling this product by sending control command consecutively.
This product can be controlled.
8 control commands can be sent consecutively.
Please send control commands in the following order.
1. Character (selecting IN)
2. Delimiter (,)
3. Character (selecting OUT)
4. Delimiter (;)
5. Character (selecting IN)
6. Delimiter (,)
7. Character (selecting OUT)
8. Delimiter (;)
・
・
・
n－3. Character (selecting IN)
n－2. Delimiter (,)
n－1. Character (selecting OUT)
n. Return
(n≦32)
※ Set the front dip switch.
Please refer to "4-1. The setting of front dip switch."
(Ex.1) Turning ON of POWER CONT, turning ON of OPTION A, turning ON of OPTION B.
ASCII Character representation
HEX representation
J , 3
;
K , 3
;
L , 3 return
4AH 33H 4BH 33H 4CH 33H
2CH 3BH 2CH 3BH 2CH 0DH
※ This product sends, ACK (06H), as answer back when operation of consecutive control
command is executed.
This product sends, NAK (15H), as answer back when operation of control command
is not executed.
-20-
c) Reading data
To read the data, the current state of this product can be understood.
Sending
1. Character (reading data command)
2. Return
Receiving
1. State of selection of CAT5
2. Delimiter (;)
3. State of selection of SUB
4. Return
(Ex.1) When IN3 is selected for CAT5 OUT and IN4 is selected for SUB OUT.
Sending
ASCII Character representation
HEX representation
W
57H
return
0DH
Receiving
ASCII Character representation
HEX representation
C
;
D
return
0DH
43H 3BH 44H
(Ex.2) When OFF is selected for CAT5 OUT, IN4 is selected for SUB OUT.
Sending
ASCII Character representation
HEX representation
W
57H
return
0DH
Receiving
ASCII Character representation
HEX representation
Q
;
D
return
0DH
51H 3BH 44H
※Do not send together with control command consecutively.
5-3-2. Registration method
Special software is needed for the command registration.
Please see instruction manual for the special software.
-21-
6. Parallel interface
This product can be controlled by connecting parallel interface.
This product can be controlled as the same operation by front buttons.
Parallel connector signal arrangement
connecter-pin
Signal
Input or Output
１
POWER_CONT
OUT
２
OUT
DISPLAY_POWER
OPTION_A
OPTION_B
OPTION_C
OPTION_D
OPTION_E
３
OUT
４
OUT
５
OUT
６
OUT
７
OUT
OPTION_F
８
OUT
９
IN1(Composite1)
IN2(Composite2)
IN3(Composite3)
IN4(Component)
IN5(RGB1)
IN6(RGB2)
IN7(RGB3)
IN8(RGB4)
CAT5
OUT
１０
１１
１２
１３
１４
１５
１６
１７
１８
１９
２０
２１
２２
２３
２４
２５
２６
２７
２８
２９
３０
３１
３２
３３
３４
３５
３６
３７
３８
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
SUB
OUT
OFF(MUTE)
-
OUT
GND
GND
GND
GND
GND
+5V
+5V
+5V
+5V
+5V
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
POWER_CONT
DISPLAY_POWER
OPTION_A
OPTION_B
OPTION_C
OPTION_D
OPTION_E
OPTION_F
３９
４０
４１
４２
４３
４４
４５
４６
４７
４８
４９
５０
IN1(Composite1)
IN2(Composite2)
IN3(Composite3)
IN4(Component)
IN5(RGB1)
IN6(RGB2)
IN7(RGB3)
IN8(RGB4)
CAT5
SUB
OFF（MUTE)
－
-22-
7．Specifications
7-1．The Specifications of this product
Model name
Input signal
Output signal
KE811CT(w-type)
Video :RGB４system、Component１system、Composite:３system、Audio:８system
Video:SUB output（RGB/component、composite）each１system、
Output for extension１system(2 distribution) Audio output :1system
Video:RGB:15pin HD female、Component/Composite:RCAconnector、Audio:RCAconnector/mini-jack
Video:RGB/component:15pin HD female、composite:RCAconnector、Audio:RCAconnector、
Output for extension RJ-45connector
Input connector
Output connector
Extension cable
Video input and output
Enhanced CAT5 cable、CAT6 cable
Analog:RGB 0.7V[p-p](75Ω)、 HD,VD :TTL
Y 1V[p-p](75Ω)、Pb/Pr ±0.35V[p-p](75Ω)
VBS/VS 1V[p-p](75Ω)
Digital: HD TTL
VD TTL
30Hz～100MHz ±3dB
－10dBu 50kΩ
Video frequency response
Audio input level
Audio output level
－10dBu loading over 10kΩ
Audio frequency response
20Hz～20kHz ±1dB
RS232C:DB9 connector×2
Ribbon connector 50-pin
6pin Terminal connector for Contact output×2、2pin Terminal connector for Power control
Temperature：0～40℃
humidity：20～80％（no condensation）
Approximately 10W
Input:AC100V-240V 50/60Hz 1.0A
Control
RS232C
and
Parallel I/O
remote
Tally I/O
Operating temperature
and humidity
Power consumption
Power (AC adapter)
Output:DC16V 2.5A
W422×D250×H44（mm)
Approximately 3kg
Dimensions
Weight
Note : This product complies with the EMC standards listed below.
EN55022 : 1998+A1 : 2000+A2 : 2003
EN61000-3-2 : 2000+A2 : 2005
EN61000-3-3 : 1995+A1 : 2001
EN55024 : 1998+A1 : 2001+A2 : 2003
-23-
7-2. The specification of control system connectors
7-2-1.Contact output connectors for power control (POWER CONT) and option (OPTION A-F)
button output
POWER
CONT
OPTION OUT
B
D
E
A
C
F
Relay specification
relay (no polarity)
relay (no polarity)
Relay type : photo MOS relay, make contact
Rating : maximum 50mA, less than AC/DC 24V
Internal circuit is as follows.
fuse
varistor
◆Caution
・Do not supply more than AC/DC 24V.
※When option button is set as momentary output, output pulse width is about 200msec.
-24-
7-2-2. Connector for tally output
25
50
4 3 2 1
26
PARALLEL REMOTE
Connector pin No. 1-19 for output
Connector pin No. 21-25 for GND
Connector pin No. 26-30 DC5V
Output type : open-collector. Pullup (internal 10KΩ, 5V connection)
Rating : maximum 20mA, DC5V
◆Caution
Do not exceed the rating. Please put register ,R, to protect overcurrent as follows.
+5V
+5V
R
R(≧50Ω）
10kΩ
2V
100Ω
MAX20mA
(KE811CT)
(Connection equipment)
(Ex.) When putting LED (forward voltage 2V), maximum current is
5-2
R+100
I＝ ≦20mA ,
and then R≧50Ω .
◆Caution
Please use within 20mA when DC5V is used.
-25-
7-2-3. Connector for parallel input
25
50
4 3 2 1
26
PARALLEL REMOTE
Connector pin No. 31-49 for input
Connector pin No. 21-25 GND
Connector pin No. 26-30 DC5V
Contact type : Non-voltage contact
※ Please use non-voltage contact by momentary switch (non-lock) or open-collector of
transistor when parallel input is executed.
Parallel remote connector
21
GND
GND
25
31
32
49
Please input as following timing.
t＞500ms
IN
t
1＞20ms
t
t1
※Parallel input may not operate when this product is controlled in serial communication.
-26-
8．Trouble shooting
Reference
Problem
Please check the following
●
●
Is the power of the connection equipment turned on ?
Is the power adapter cable properly connected to
AC100-240V line and this product ?
Is the POWER CONT button of this product turned on?
Is the CAT5e or CAT6 cable properly connected to OUT 1
or OUT2 of this product?
－
－
The video can't be
seen
－
－
●
●
→3-3.Cable mounting kit
and Rack mounting kit
－
●
Isn't unexpected fore applied to the CAT5e or CAT6 cable
connected to OUT1 or OUT2 of this product ?
Is the cable properly connected to the video input connector?
Is the INPUT button properly selected ?
●
●
→4-3.Operation of buttons
→4-3.Operation of buttons
● Is the CAT5，SUB button properly selected ?
●
●
Are cables properly connected to IN connectors?
Is the length of the cable within the recommended maximum
transmission distance ?
－
→1-2.General information
●
Are the cables wired correctly?
→3-2.Preparation of cable
－
● Is the power of the twisted pair receiver turned on ?
● Did you adjust a LEVEL /PEAKING of a twisted pair receiver?
Please refer to the instructions
manual of the receiver with
this product.
The video is
flickering or there
is noise
●
●
●
●
●
Is the twisted pair cable near the AC line? It should be far
from the line.
Is there a source causing noise close to AC adapter of this
product ? A noise filter should be used in case of noise.
Is the CAT5e or a CAT6 cable properly connected to OUT 1 or
OUT2 of this product ?
Isn't unexpected fore applied to the CAT5e or CAT6 cable
connected to OUT1 or OUT2 of this product ?
Is the cable properly connected to the video input connector
of this product?
－
－
－
→3-3.Cable mounting kit
and Rack mounting kit
－
●
●
Are cables properly connected to IN connectors?
Is the length of the cable within the recommended maximum
transmission distance?
－
→1-2.General information
●
Did you adjust a LEVEL /PEAKING of a twisted pair receiver?
Please refer to the instructions
manual of the receiver with
this product .
－
－
－
Sound can't be output
●
●
●
Is the power of the connection equipment turned on ?
Is the POWER CONT button of this product turned on?
Is the power adapter cable properly connected to
AC100-240V line and this product ?
－
－
－
●
Is the INPUT button properly selected ?
● Is the CAT5，SUB button properly selected ?
● Is the CAT5e or CAT6 cable properly connected to OUT 1
or OUT2 of this product?
→3-3.Cable mounting kit
and Rack mounting kit
－
●
Isn't unexpected fore applied to the CAT5e or CAT6 cable
connected to OUT1 or OUT2 of this product ?
Is the cable properly connected to the AUDIO IN connector
of this product?
Is the power of the twisted pair receiver turned on ?
Is the length of the cable within the recommended maximum
transmission distance?
●
－
●
●
→1-2.General information
-27-
Sound has noise
● Is the twisted pair cable near the AC line? It should be far
from the line.
● Is there a source causing noise close to AC adapter of this
product ? A noise filter should be used in case of noise.
● Is the CAT5e or a CAT6 cable properly connected to OUT 1
or OUT2 of this product ?
－
－
－
●
Isn't unexpected fore applied to the CAT5e or CAT6 cable
connected to OUT1 or OUT2 of this product ?
→3-3.Cable mounting kit
and Rack mounting kit
－
● Is the cable properly connected to the AUDIO IN connector
of this product?
● Is the cable properly connected to the AUDIO OUT connector
of the twisted pair receiver ?
－
● Is the length of the cable within the recommended
transmission distance?
→1-2.General Information
●
Is the cable properly connected ?
Serial
communication
can't be performed.
→5-2.Connection of
RS232C cable
－
●
●
Does the kind of cable suit?（straight or cross）
Does a setup of a front dip switch suit?
→4-1.The setting of
front dip switch
→5-3-1.Control method
●
●
Does the command suit?
Command
registration can't be
performed.
Is the cable properly connected ?
→5-2.Connection of
RS232C cable
－
●
●
Does the kind of cable suit?（straight or cross）
Does a setup of a front dip switch suit?
→4-1.The setting of
front dip switch
-28-
B
&
2006.4.14
※Design and specifications are subject to change without notice.
|