6
MULTI-BAND RADIO
KH 2029
Multi-Band Radio
Operating instructions
KOMPERNASS GMBH
BURGSTRASSE 21 · D-44867 BOCHUM
ID-Nr.: KH2029-11/09-V1
CONTENTS
PAGE
Intended use
Technical Data
Symbols used
2
2
4
Safety information
Operating elements
Starting up
General functions
Time functions
5
9
10
12
12
Time, date, time zone and world time . . . . . . . . . . . . . . . . . . . . .13
Select display mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Alarm function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Stop watch function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Countdown function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Radio operation
24
Setting the station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Fine tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Aerial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Memory functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Cleaning
Disposal
Importer
Warranty & Service
29
29
30
31
- 1 -
MULTI-BAND RADIO KH2029
Before using the device for the first time, read these operating instructions
carefully and keep them for later reference. Hand the instructions over
when transferring the device to a third party.
This documentation is copyright protected. Every duplication resp. every
copying, also as extracts, as well as any reproduction of images, even in an
altered state, is only permitted with the written consent of the manufacturer.
Intended use
This device is designed to receive generally approved radio transmissions
in all countries (world receiver) and only for domestic use.
Utilisation other than as described here is not permitted and it could lead
to damages and injuries. No liability will be accepted for damages resulting
from misuse or improper handling, the application of force or unauthorised
modifications.
Technical Data
This appliance fulfills, in regard to conformity with, the fundamental require-
ments and other relevant provisions of the EMC Directive 2004/108/EC,
the Low Voltage Directive 2006/95/EC and the Ecodesign Directive
2009/125/EC (Commission Regulation 1275/2008 Annex II, No .1).
- 2 -
Power consumption:
5 watts
Power consumption Standby: 1.4 W
Operating temperature:
Humidity:
Dimensions (W x H x D):
Appliance weight:
+5 +35°C
~
5
90% (no condensation)
~
181 x 111 x 39 mm
375 g approx.
Power transformer weight:
185 g approx.
Batteries
4x 1.5 V, Type AA/LR6/Mignon (not supplied)
Frequency range radio:
VHF (FM):
87 – 109 MHz
SW:
5.85 – 17.90 MHz
522 – 1656 kHz
520 – 1710 kHz
144 – 299 kHz
MW (AM) Europe
MW (AM) USA
LW
The technical features of the device enable the frequency ranges stated
above to be set. Various countries may have different national rules on the
radio frequency ranges assigned. Please note that you may not sell, transfer
to third parties or abuse information received outside the assigned radio
frequency ranges.
Tuning ranges (NORMAL/FINE):
FM (VHF)
100 kHz /50 kHz
SW
5 kHz /1 kHz
MW (AM) Europe
MW (AM) USA
LW
9 kHz /1 kHz
10 kHz /1 kHz
1 kHz
Sensitivity:
SW can be set to 2 intervals
- 3 -
General
Memory positions :
1600 (400 for each frequency range)
Headphones
Model:
Impedance:
E105
32 Ω
Wideband characteristic
Voltage (WBCV):
Headphone socket
max. Output voltage:
Power transformer
Manufacturer:
Model:
approx. 206 mV
approx. 80 mV
S&S MFG. LTD.
A400-75
Primary:
Secondary:
230 V 50 Hz / 30 mA
7.5 V DC 400 mA / 3VA
~
Symbols used
These symbols bring to your attention that here a warning notice
follows in regard to one of the following matters:
- Risk of injury,
- Risk of electric shocks,
- Risk of fire,
- Risk of explosion,
plus bringing your attention to important matters such as:
- Information regarding the handling of batteries,
- Information about voltage surges,
- Information about mains-power disconnection.
- 4 -
This symbol warns about submersing the appliance in water or
other liquids.
This symbol warns you about hearing damage.
Note:
With this symbol you are given tips about interaction with the appliance.
Safety information
•
This device has not been designed for use by people (including children)
with restricted physical, sensory or intellectual abilities or lack of expe-
rience and/or knowledge, unless they are supervised by a responsible
person (for their own safety) or have received instructions on how to
use the device.
•
•
•
•
Children should be supervised to ensure that they do not play with
the device.
In order to avoid the device being switched on unintentionally, remove
the adapter from the mains socket after each use and before cleaning.
Check the device and all parts for visible damage. The device’s safety
concept can only work if the device is in perfect condition.
A mains adapter connected to the device must always be easily
accessible so that the device can be quickly disconnected from the
mains power in an emergency.
- 5 -
Risk of electric shock!
•
Connect the mains-power adapter only to correctly installed and
earthed mains sockets. Ensure that the rating of the local power
supply tallies completely with the details given on the rating plate of
the appliance.
•
•
Damaged adapters or mains cables should be exchanged immediately
by an authorised technician or the Customer Service in order to
avoid risks.
Connection cables or devices that do not work perfectly or have been
damaged should be repaired or exchanged immediately by Customer
Services.
Never immerse the device in water! Simply wipe it with a slightly
damp cloth.
•
Do not expose the wall wart to rain or use it in a damp or wet
environment.
•
•
Ensure that the connection cable is never wet or damp when in use.
You must not open or repair the device’s housing. This can be dangerous
and renders the warranty null and void.
•
Protect the device from moisture and sprayed water. Therefore do not
place any objects filled with water (e.g. vases) on or near the device.
Risk of fire!
•
•
Do not use the device near hot surfaces.
Do not set the device up where it is exposed to direct sunlight.
This could cause it to overheat and damage it beyond repair.
Never leave the device unattended during operation.
Never cover the device’s ventilation slots when it is switched on.
Do not place open flames, such as candles, on or near the device.
•
•
•
- 6 -
Risk of injury
•
•
Keep children away from the connection cable and device.
Children frequently underestimate the danger of electrical devices.
If the device has fallen down or is damaged it must no longer be used.
Have the device checked by a qualified specialist and, if necessary,
repaired.
•
Batteries must not be handled by children.
Children can put batteries in their mouths and swallow them.
If a battery has been swallowed, obtain medical assistance immediately.
Thunder storms!
Devices connected to mains power can be damaged during a thunder
storm. If there is a thunder storm, always remove the mains plug from
the socket.
Information on voltage surges (EFT/electrical fast
transient) and electrostatic discharges:
If the product does not work properly due to electrical fast transient
processes (voltage surges) or electrostatic discharge, it must be
reset to restore normal operation. If necessary, remove the plug from
the power socket and insert it again. The batteries (if used) must be
removed and reinserted.
Information on separating the device from
mains power
The POWER button on this device does not completely separate it from
the mains network. In addition, the device uses power when in standby
mode. In order to completely separate the device from the mains supply
the plug must be removed from the mains socket.
- 7 -
Notes on handling batteries
The device uses batteries. Please note the following on handling batteries:
Risk of explosion!
Do not throw batteries into a fire. Do not recharge batteries.
•
•
•
Never open, solder or weld batteries. There is a risk of explosion and injury!
Check batteries regularly. Leaking batteries can damage the device.
If the appliance is not going to be used for long periods, remove the
batteries.
•
•
If batteries leak, put on protective gloves.
Clean the battery compartment and contacts with a dry cloth.
Caution!
No liability/warranty applies to damage to the device caused by
moisture due to water penetrating the device or overheating!
- 8 -
Operating elements
Ạ Front panel
Save buttons M.0/5 - M.4/9
Display
Button SNOOZE
Waveband selector switch (LW/SW/MW/FM)
POWER button
FINE button
PAGE button
UP/DOWN buttons
VOL+(AL-1)/VOL-(AL-2) buttons
MODE button
q
w
e
r
t
y
u
i
o
a
s
d
f
g
BASS button
MEMORY SCAN button
MEM button
Loudspeakers
ạ Back
Stand
Aerial
Carrying strap
switch SW SEN. (DX/LX)
Headphone output
h
j
k
l
;
2)
EXT. DC 7.5 V 400 mA: Mains adapter connection
- 9 -
Starting up
Unpack the device
Remove all packaging materials.
Caution!
Do not let children play with the plastic film. There is a risk of suffocation.
Check the items supplied
Whilst unpacking, check that all of the following items are available to you:
• Shortwave Radio
• Power transformer
• Headphones
• Storage case
• These operating instructions
Mains and battery operation
When you disconnect the radio from the mains supply, any settings you
may have made (time, alarm, stations in memory) will be lost. If you wish
to keep these settings, insert batteries (see below) before disconnecting.
Inserting batteries
The device can also be operated with batteries (not supplied) as well as
from the mains. You will need four 1.5V mignon batteries, size AA, LR6.
•
•
Open the battery compartment on the rear of the device by sliding
the cover downwards.
Insert four batteries into the compartment, paying attention to
the polarity.
- 10 -
•
Replace the cover on the battery compartment.
If the batteries are too weak, this is indicated on the screen by a flashing
symbol
.
Mains connection
•
Connect the plug of the mains adapter to the EXT. DC 7.5 V 400 mA socket
on the side of the device.
•
Plug the mains adapter into an easily accessible socket. To avoid
tripping hazards, please avoid using an extension cable.
Connecting headphones
On the left side of the radio, you will find the headphone socket.
Caution!
With this appliance, use only the supplied type E105 headphones.
•
Insert the headphone jack plug into the headphone output.
The speaker will be deactivated automatically.
Caution:
Listening to music with headphones for long periods and at high
volume levels can lead to hearing damage!
- 11 -
General functions
Key lock
In order to prevent changing the settings unintentionally by touching the
buttons, you can activate the key lock.
•
•
Press and hold down the MEM button for around 3 seconds.
On screen, the message
flashes. All buttons, except the buttons
SNOOZE and MEM, are now blocked.
Press and hold down the MEM button again for about 3 seconds to
cancel the key lock. The
message on the screen disappears.
Screen lighting
•
Press any button to illuminate the screen. The screen will remain lit for
about 10 seconds.
Stand
•
Fold out the base on the rear of the device to make the device
more stable.
Time functions
When the power supply is effective (mains or battery operation), the device
launches with an automatic update.
"SYSTEM SETTING PLEASE WAIT" appears in the display.
When an RDS signal is received, the time and date are adjusted automa-
tically. Subsequently, the current time is shown in the display.
If the time is not adjusted automatically, make the settings manually,
as explained in the following sections.
- 12 -
The time functions can only be set when the radio is switched off. If an RDS
signal is not received at the first switch-on, the pre-adjusted time for the
multi-band radio begins with "0:00 00".
If the device is disconnected from its power supply the settings are lost.
Time, date, time zone and world time
You can set the time, date and time zone via the MODE button. In addition,
you can check and adjust the world time, the date alarm, medium wave
reception, the alarm time interruption and the hour mode as well as switch
the automatic update on or off.
When you press the button MODE with the radio switched off, the function to be
programmed blinks for about 15 seconds. During this time, adjust the setting
with the UP/DOWN buttons.
•
•
•
•
•
•
•
•
•
Press MODE x 1: Setting clock time
Press MODE x 2: Setting the date
Press MODE x 3: Set time zone (“Local City”)
Press MODE x 4: Show world time
Press MODE x 5: Date alarm
Press MODE x 6: Set reception range for medium wave.
Press MODE x 7: Set alarm pause.
Press MODE x 8: Set 12/24 hour mode.
Press MODE x 9: Switch automatic update on/off
To apply a setting, just wait until the screen stops flashing (the screen reverts
to the time indication) or press MODE to move on to the next function.
- 13 -
Setting clock time
•
•
Press MODE once. The most recently set time flashes on the screen.
Press the UP or DOWN button to move the time forward or backward at
minute intervals. Hold down one of the buttons for a few seconds to
move the setting forward or backward quickly at 10 minute intervals.
Note:
Set the time without summer time offset. If summer time is required, this can be
set when setting the time zone.
Setting the date
• Press MODE again or twice.
The date set flashes on the screen (“Tu 1- 01- 08” when first switched on).
•
Press the UP or DOWN button to move the date forward or backward.
Keep either of these buttons pressed for a few seconds to change the
date in ten-day steps.
The weekday indication follows automatically. The indication uses the first
two letters of the English name of the day.
The built-in calendar runs from 2000 to 2099.
Day of the week indication:
Su = Sunday
Mo = Monday
Tu = Tuesday
We = Wednesday
Th = Thursday
Fr = Friday
Sa = Saturday
- 14 -
Setting the time zone
•
Press MODE again or three times. The selected time zone flashes on the
screen as the abbreviation for the corresponding city (UTC when first
switched on); the time disappears.
•
Press the UP or DOWN button to move the time zone forward or backward.
The following table summarises the city abbreviations for the time zones and
time differences.
- 15 -
Summer time
no
Short code
Difference from CET
Town
HNL
ANC
YVR
-10:00
-9:00
-8:00
-8:00
-7:00
-6:00
-6:00
-5:00
-5:00
-5:00
-4:00
-3:00
-3:00
0:00
0:00
1:00
1:00
1:00
1:00
2:00
2:00
3:00
3:00
4:00
5:00
6:00
7:00
8:00
8:00
8:00
9:00
10:00
11:00
12:00
Honolulu/USA
yes
yes
yes
yes
yes
no
Anchorage/USA
Vancouver/Canada
Los Angeles/USA
Denver/USA
LAX
DEN
CHI
Chicago/USA
MEX
NYC
YYZ
Mexico City/Mexico
New York/USA
yes
yes
yes
no
Toronto/Canada
Montreal/Canada
Caracas/Venezuela
Rio de Janeiro/Brazil
Buenos Aires/Argentina
Universal Time Coordinated
London/GB
YUL
CCS
RIO
no
no
BUE
UTC*
LON
MUN
FRA
yes
yes
yes
yes
yes
yes
no
Munich/Germany
Frankfurt/Germany
Paris/France
PAR
ROM
CAI
Rome/Italy
Cairo/Egypt
yes
yes
no
IST
Istanbul/Turkey
MOW
KWI
DXB
KHI
Moscow/Russia
Kuwait City/Kuwait
Dubai/United Arab Emirates
Karachi/Pakistan
Dhaka/Bangladesh
Bangkok/Thailand
Singapore
no
yes
yes
no
DAC
BKK
SIN
no
no
HKG
PEK
Hong Kong
no
Beijing/China
no
TYO
SYD
NOU
AKL
Tokyo/Japan
yes
no
Sydney/Australia
Noumea/New Caledonia
Auckland/New Zealand
yes
- 16 -
*UTC
Universal Time Coordinated (UTC). UTC is the reference for the times of the
various time zones around the world.
Summer time offset
Not every time zone around the world differentiates between summer and
winter time. To display your timezone correctly you must, subject to the
actual time zone, activate or deactivate the Summer Time offset.
•
While the time zone indication is still flashing, press the SNOOZE button.
The screen shows the SUN OFF message when summer time has been
deactivated.
•
Press the SNOOZE button again. The screen now shows SUN ON. Summer
time offset is now activated and the clock moves one hour ahead.
Show world time
•
Press MODE again or four times to show the world time. The city
abbreviation appears with the corresponding time.
•
Press the UP or DOWN button to move the time zone forward or backward.
Note:
To properly show your programmed world time, you must activate or
deactivate the Summer Time offset for each world time.
- 17 -
Special date alarm
•
•
•
•
•
Press the MODE button a fifth time to set the special date alarm.
The screen flashes SDA1 and the date in succession.
Press the PAGE button to select one of the ten settable date alarms
(SDA1–SDA 10).
Press the UP or DOWN button to set the date on which the alarm should
sound.
Press the SNOOZE button to ignore the year number setting so that the
alarm sounds every year.
When the current date tallies with the date of the SDA alarm,
at 08.00 on this day the alarm tone will sound.
In addition, the SDA message will flash on the screen.
Turn off the alarm by pressing any button.
•
Note:
In order to completely deactivate the date alarm set a date that is in the past!
Setting 12/24 hour mode
•
Press MODE eight times. The screen shows the”24 HR” message for
24-hour mode.
•
•
Press the UP button to set the 24 hour mode.
Press the DOWN button to set the 12 hour mode.
“12 HR” is displayed on the screen. In the afternoon in addition PM is
shown on the screen.
- 18 -
Switch Automatic Update (RDS) On/Off
With this function the device can automatically update the settings for date
and time from the RDS signal.
• Press the button MODE nine times. In the display the indication UPDA ON
appears.
• Press the button DOWN to switch the automatic update off.
• Press the button UP to switch the automatic update back on.
Select display mode
You can select which information is shown on the screen when the radio is
switched off.
The selected mode is indicated by a corresponding symbol on the screen.
When the radio is switched off, select the display mode by repeatedly
pressing the FINE button in accordance with the following table:
Symbol on the screen display mode
CLK
only the time is displayed
CITY
DATE
CIT DAT
The time and world time are shown in succession
The time and date are shown in succession
the time, date and world time are shown in succession
Alarm function
This multi-band radio provides you with two independently adjustable
alarm times, AL1 and AL2. You can programme for both ...
...if the device should sound an alarm on every workday, at the
weekend, the whole week or on a single specific weekday;
...if the alarm should sound with an alarm tone or with the radio.
- 19 -
Setting the alarm time
You can set two alarm times in your world receiver.
Alarm function
Radio
Symbol on the screen
Acoustic signals
Switched off
No symbol
•
•
With the radio switched off, press the buttons VOL.+/AL–1 (or VOL.-/AL–2).
The screen shows the most recently set alarm time and the symbol for
the alarm type.
Press the UP or DOWN button to move the alarm time forward or backward
at minute intervals. Hold down one of the buttons for a few seconds to
move the setting forward or backward quickly at 10 minute intervals.
Press the VOL.+/AL–1 (or VOL.–/AL–2) button until the desired alarm function
(see table above) is indicated on the screen.
•
•
Press the SNOOZE button to set the weekday on which you want the
alarm to sound:
You can select between workdays (Mo, Tu, We, Th, Fr), weekends (Sa, Su),
the whole week (Su, Mo, Tu, We, Th, Fr, Sa) or a single weekday.
The selected setting is shown on the display.
- 20 -
•
•
Press the SNOOZE button until the desired alarm days are set. Hold down
the SNOOZE button until the screen shows an individual week day.
Press the SNOOZE button to set the desired week day.
To go back to selecting week days, weekend or every day, briefly hold
down the SNOOZE button again.
•
Press the MODE button to save the setting and return to the time mode.
The setting is also saved if you wait around 15 seconds until the
screen returns to displaying the time.
When the alarm sounds...
•
and the “Radio” alarm function has been selected, the radio operates
for one hour at a predefined alarm volume. To switch off press the
VOL.+/AL–1 (or VOL.–/AL–2) button.
•
and the “signal sounds” alarm function has been selected, the signal
sound is played for 10 minutes. To switch off press the VOL.+/AL–1
(or VOL.–/AL–2) button.
Note:
Please note that a station must be selected for the radio alarm to work.
Interrupting the alarm
•
Press the SNOOZE button to interrupt the alarm for 10 minutes.
- 21 -
Set snooze time
•
With the radio switched off, press the button MODE seven times.
The screen displays the snooze time set (default is”SNO 10”).
Use theUP and DOWN buttons to set the snooze time to a time between
1 and 59 minutes.
•
Turning off the alarm function
•
Press the VOL.+/AL–1 or VOL.–/AL–2 button until the relevant alarm symbols
disappear from the screen.
Stop watch function
The stop watch function is only available when the radio is switched off.
•
Press and hold down the PAGE button for around 2 seconds, the screen
shows 00.00.0 U.
•
Press SNOOZE to start the stop watch. The maximum time for the stop
watch is 99 minutes and 59 seconds. If the stop watch exceeds the
maximum time, 99:59.0 is displayed and flashes.
During time measurement, it can be stopped by pressing SNOOZE.
Pressing SNOOZE again restarts the stop watch.
•
•
•
•
Hold down SNOOZE to reset the stop watch.
Leave the stop watch by pressing PAGE.
Countdown function
The countdown function is only available when the radio is switched off.
Set and save countdown
•
Press and hold down the MEMORY SCAN button for around 2 seconds,
the screen shows D 00.00.
- 22 -
•
Press the UP or DOWN button to set the desired time.
5 countdown times are preset on the memory buttons and you can open
these directly using the corresponding memory button:
Button M.0/5
Button M.1/6
Button M.2/7
Button M.3/8
Button M.4/9
10:00
30:00
45:00
60:00
90:00
•
Press the MEM button to save the set time, the memory space indicator
MEM flashes on the screen. Now use the M.0/5–M.4/9 buttons to select
a memory space; when you press the relevant memory key the time is
saved in this memory space and the time previously stored there
overwritten.
•
When the MEMORY SCAN button is pressed again you leave the
countdown mode.
Call up and activate the countdown function
•
•
•
Press and hold down the MEMORY SCAN button for around 2 seconds,
the screen shows D 00. 00.
Select the desired, saved countdown time with the aid of the M.0/5–M.4/9
memory buttons.
Press SNOOZE to start the countdown. Pressing the SNOOZE button again
pauses the countdown.
When the set time has been counted down, an alarm sound plays for one
minute becoming gradually higher in tone and louder.
•
Press the MEMORY SCAN button to pause the countdown and leave
countdown mode.
- 23 -
Radio operation
Switching on/volume control
•
Press the POWER button to switch the radio on. ON will appear briefly on
the screen, followed by the current frequency and band selection.
Press the VOL.+/AL–1 or VOL.–/AL–2 button to control the volume:
Button VOL.–/AL–2: quieter;
•
Button VOL.+/AL-1: louder.
The volume is shown on the bar indicator to the bottom right of the screen.
Switch on bass amplifier
•
When the radio is switched on, press the BASS button to switch on the
bass amplifier. The screen will flash BASS.
•
In order to switch the bass amplifier off again, press BASS one more
time. The BASS message disappears.
Switch display message
•
In radio operation press the MODE button to switch between displaying
the time and frequency.
Turning off
Switch the radio off by pressing the POWER button. OFF is shown briefly
on the screen and the time is displayed again.
•
- 24 -
Sleep function
You can activate the sleep function via the SNOOZE button. You can set a
time of up to 90 minutes in ten-minute steps, after which the radio will auto-
matically turn itself off. To do so, first switch the radio off.
•
•
•
Press the SNOOZE button. The symbol for the sleep function
90 (for 90 minutes) will appear.
Press the SNOOZE button repeatedly until 90 is displayed to count down
the sleep time in 10 minute steps.
and
Either select a sleep time (the sleep symbol
remains on the screen)
or press SNOOZE again until 00 appears on the screen.
The sleep time is now switched off.
Setting the station
•
Select the required frequency band (FM, MW, LW or SW), using the
frequency select button.
The corresponding abbreviation will appear on the screen.
•
•
The UP and DOWN buttons can now be used to set the desired frequency.
If you keep UP or DOWN pressed for about three seconds, the automatic
station search will start.
•
The search stops as soon as a station with sufficient signal strength is
found.
Setting the MW band
Since the radio transmitter systems differ from one country to another,
you should make the appropriate setting via the reception range setting:
•
With the radio switched off, press the button MODE six times and then
select, using the buttons UP resp. DOWN, the appropriate reception range
as per the following table:
- 25 -
Region Channel
spacing
Band range
Amerika 10 kHz
520-1710 kHz
522-1656 kHz
Europa 9 kHz
Fine tuning
If a station can not be found precisely the fine tuning can be use to improve
reception.
•
•
•
During the channel search press the FINE button, the screen shows
FINE.
Now, using the buttons UP resp. DOWN, adjust the required reception
range with smaller frequency steps.
By pressing the FINE again you leave the fine tuning function again.
This function is not available for the LW frequency range.
Aerial
The rotatable telescopic aerial on the radio can be used for the FM and
SW bands.
•
Pull the aerial out fully and arrange it for optimum reception.
The SW SEN. switch on the left side of the device can be used to improve the
reception quality for the SW band. Select LX for strong stations and DX to
improve reception for weak stations.
The telescopic aerial does not work in the MW and LW bands. In these
bands, the radio uses its built-in ferrite aerial.
•
Align the radio for best reception.
- 26 -
Memory functions
Save station
The world receiver can save 400 stations in each frequency range.
To store a station, proceed as follows:
•
•
•
Set the frequency range with the frequency selection switch and then
the station that you want to save.
Press the MEM button. The screen shows the PAGE memory page and
MEM flashes.
Within 10 seconds press the PAGE button (the PAGE message flashes),
and then select a memory page (from 00–39) using the UP or DOWN
button.
•
•
Within 10 seconds use the M.0/5–M.4/9 buttons to select a memory
space to store the station. For example, press the M.0/5 button once
for memory space 0 and again for memory space 5. The occupancy
is shown on the screen.
Press MEM again to save the station. The PAGE and MEM messages
are shown on a permanent basis.
Note:
If the world receiver is connected to the mains adapter and no
batteries have been inserted, the station memories are lost when
the adapter plug is pulled from the socket.
- 27 -
Selecting a saved station
•
•
•
In order to select a saved station directly, first use the frequency selection
switch to select the frequency range where the station is saved.
Press the PAGE button and then use the UP or DOWN buttons to select a
memory page (from 00–39).
Within 10 seconds press the M.0/5–M.4/9 buttons to select a memory
space to store the station.
The station is played immediately after entering the memory space.
Carry out automatic station search
Your world receiver can search the frequencies within a range and store
the stations it finds. Do the following to activate the automatic search
(automatic memory scan/AMS):
•
•
Press the MEM button once. The MEM message flashes.
Hold down the MEMORY SCAN button for about 1 second.
The world receiver now searches all frequencies in the currently selected
frequency range and saves the stations it finds from the currently set memory
page and memory space.
Displaying memory spaces
•
Press the MEMORY SCAN button to call up the content of all station memo-
ries for the selected band.
All stored stations will be played in succession for about five seconds.
•
Press the button SNOOZE to finish the rendering of the memory positions.
Note:
Please take note that with this the snooze function will be activated.
Repeatedly press the button SNOOZE until 00 appears in the display.
- 28 -
Cleaning
Risk of injury from electric shock:
• Disconnect the device from the mains power before cleaning it!
• Never immerse the device’s parts into water or other liquids!
• Do not allow liquid to penetrate the housing.
Cleaning the housing:
Clean the housing surface with a slightly damp cloth.
Never use petrol, solvent or detergents that could attack the plastic!
Disposal
Device disposal
Never dispose of the device in the normal household rubbish.
Dispose of the device using an authorised disposal company or your
local disposal facility. This device is subject to European Directive
2002/96/EC. Please follow the currently valid regulations.
In case of doubt, contact your disposal facilities.
Disposal of batteries
Batteries must not be disposed in the household rubbish. Each consumer is
obliged by law to bring batteries/rechargeable batteries to a collection
point provided by the local authority/council or to retailers.
This obligation is so that the batteries can be disposed of in an environmen-
tally friendly manner. Only hand in batteries that have been discharged.
- 29 -
Disposal of packaging
Ensure all packaging materials are disposed in an environmentally
friendly manner.
Importer
KOMPERNASS GMBH
BURGSTRASSE 21
D-44867 BOCHUM
- 30 -
Warranty & Service
The warranty for this appliance is for 3 years from the date of purchase.
The appliance has been manufactured with care and meticulously
examined before delivery. Please retain your receipt as proof of purchase.
In the event of a warranty claim, please make contact by telephone with
our Service Department. Only in this way can a post-free despatch for your
goods be assured. The warranty covers only claims for material and
maufacturing defects, but not for transport damage, for wearing parts or
for damage to fragile components, e.g. buttons or batteries. This product is
for private use only and is not intended for commercial use. The warranty
is void in the case of abusive and improper handling, use of force and
internal tampering not carried out by our authorized service branch.
Your statutory rights are not restricted in any way by this warranty.
The warranty period will not be extended by repairs made under warranty.
This applies also to replaced and repaired parts. Any damage and defects
extant on purchase must be reported immediately after unpacking the
appliance, at the latest, two days after the purchase date. Repairs made
after the expiration of the warranty period are subject to payment.
DES UK LTD
Tel.: 0871 5000 700 (£ 0.10 / minute)
e-mail: [email protected]
Kompernass Service Ireland
Tel: 1850 930 412 (0,082 EUR/Min.)
Standard call rates apply. Mobile operators may vary.
e-mail: [email protected]
- 31 -
|