CD-RECEIVER
KDC-219
INSTRUCTION MANUAL
AMPLI-TUNER-LECTEUR DE CD
KDC-2019V
KDC-2019
KDC-29MR
KDC-119
MODE D’EMPLOI
REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM
MANUAL DE INSTRUCCIONES
RECEPTOR DE CD
MANUAL DE INSTRUÇÕES
Take the time to read through this instruction manual. Familiarity with installa-
tion and operation procedures will help you obtain the best performance from
your new CD-receiver.
KDC-119S
KDC-217
For your records
Record the serial number, found on the back of the unit, in the spaces designated on
the warranty card, and in the space provided below. Refer to the model and serial
numbers whenever you call upon your KENWOOD dealer for information or service on
the product.
Model KDC-219, KDC-2019V, KDC-2019, KDC-29MR, KDC-119,
KDC-119S, KDC-217, KDC-217S Serial number
KDC-217S
© B64-2114-00 (KWN)
2Warning
NOTE
2CAUTION
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
Use of controls or adjustments or performance
of procedures other than those specified
herein may result in hazardous radiation
exposure.
In compliance with Federal Regulations,
following are reproductions of labels on, or
inside the product relating to laser product
safety.
reasonable protection against harmful
interference in a residential installation. This
equipment may cause harmful interference to
radio communications, if it is not installed and
used in accordance with the instructions.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is
KENWOOD CORPORATION
2967-3, ISHIKAWA-CHO,
HACHIOJI-SHI
TOKYO, JAPAN
KENWOOD CORP. CERTIFIES THIS EQUIPMENT
CONFORMS TO DHHS REGULATIONS N0.21 CFR
1040. 10, CHAPTER 1, SUBCHAPTER J.
encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
Location : Bottom Panel
• Increase the separation between the
equipment and receiver.
FCC WARNING
• Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
This equipment may generate or use radio
frequency energy. Changes or modifications to
this equipment may cause harmful
• Consult the dealer or an experienced
radio/TV technician for help.
interference unless the modifications are
expressly approved in the instruction manual.
The user could lose the authority to operate
this equipment if an unauthorized change or
modification is made.
NOTE
This Class B digital apparatus complies with
Canadian ICES-003.
— 3 —
Safety precautions
IMPORTANT INFORMATION
About the disc changer to be
connected:
2WARNING
2CAUTION
To prevent injury or fire, take the
following precautions:
• Insert the unit all the way in until it is fully
locked in place. Otherwise it may fall out of
place when jolted.
• When extending the ignition, battery, or
ground wires, make sure to use automotive-
grade wires or other wires with a 0.75mm2
(AWG18) or more to prevent wire
deterioration and damage to the wire
coating.
• To prevent a short circuit, never put or leave
any metallic objects (such as coins or metal
tools) inside the unit.
• If the unit starts to emit smoke or strange
smells, turn off the power immediately and
consult your Kenwood dealer.
• Make sure not to get your fingers caught
between the faceplate and the unit.
• Be careful not to drop the unit or subject it to
strong shock.
The unit may break or crack because it
contains glass parts.
To prevent damage to the machine,
take the following precautions:
• Make sure to ground the unit to a negative
12V DC power supply.
• Do not open the top or bottom covers of the
unit.
• Do not install the unit in a spot exposed to
direct sunlight or excessive heat or humidity.
Also avoid places with too much dust or the
possibility of water splashing.
• Do not set the removed faceplate or the
faceplate case in areas exposed to direct
sunlight, excessive heat or humidity. Also
avoid places with too much dust or the
possibility of water splashing.
• To prevent deterioration, do not touch the
terminals of the unit or faceplate with your
fingers.
• Do not subject the faceplate to excessive
shock, as it is a piece of precision
equipment.
• When replacing a fuse, only use a new one
with the prescribed rating. Using a fuse with
the wrong rating may cause your unit to
malfunction.
To connect a disc changer having the "O-N"
switch to this unit, set the "O-N" switch to "N".
To connect a disc changer having no "O-N"
switch to this unit, the converter cord CA-
DS100 and/or switching adapter KCA-S210A
are required as options.
A disc changer doesn't work when it is
connected without using these options.
If a model with no "O-N" switch is connected,
some unavailable functions and information
that cannot be displayed are generated.
Note that none of the KDC-C100, KDC-C302,
C205, C705, and non-Kenwood CD changers
can be connected.
You can damage both your unit and the CD
changer if you connect them incorrectly.
Do Not Load 3-in. CDs in the CD slot
If you try to load a 3 in. CD with its adapter
into the unit, the adapter might separate from
the CD and damage the unit.
• Do not touch the liquid crystal fluid if the
LCD is damaged or broken due to shock. The
liquid crystal fluid may be dangerous to your
health or even fatal.
If the liquid crystal fluid from the LCD
contacts your body or clothing, wash it off
with soap immediately.
• To prevent a short circuit when replacing a
fuse, first disconnect the wiring harness.
• Do not place any object between the
faceplate and the unit.
• Do not use your own screws. Use only the
screws provided. If you use the wrong
screws, you could damage the unit.
— 4 —
Cleaning the Faceplate Terminals
If the terminals on the unit or faceplate get
dirty, wipe them with a dry, soft cloth.
Lens Fogging
NOTE
Right after you turn on the car heater in cold
weather, dew or condensation may form on
the lens in the CD player of the unit. Called
lens fogging, CDs may be impossible to play.
In such a situation, remove the disc and wait
for the condensation to evaporate. If the unit
still does not operate normally after a while,
consult your Kenwood dealer.
• If you experience problems during
installation, consult your Kenwood dealer.
• If the unit does not seem to be working
right, try pressing the reset button first. If
that does not solve the problem, consult
your Kenwood dealer.
• Press the reset button if the Disc auto
changer fails to operate correctly. Normal
operatin should be restored.
Cleaning the Unit
If the faceplate of this unit is stained, wipe it
with a dry soft cloth such as a silicon cloth.
If the faceplate is stained badly, wipe the stain
off with a cloth moistened with neutral
cleaner, then wipe neutral detergent off.
Applying spray cleaner directly to the unit may
affect its mechanical parts. Wiping the
faceplate with a hard cloth or using a volatile
liquid such as thinner or alcohol may scratch
the surface or erases characters.
Cleaning the CD Slot
As dust tends to accumulate in the CD slot,
clean it every once in a while. Your CDs can
get scratched if you put them in a dusty CD
slot.
Reset button
• Characters in the LCD may become difficult
to read in temperatures below 41 ˚F (5 ˚C).
• The illustrations of the display and the panel
appearing in this manual are examples used
to explain more clearly how the controls are
used. Therefore, what appears on the display
in the illustrations may differ from what
appears on the display on the actual
equipment, and some of the illustrations on
the display may represent something
impossible in actual operation.
— 5 —
About CDs
Handling CDs
• Don’t touch the recording surface of the CD.
CD cleaning
Clean from the center of the disc and move
outward.
Removing CDs
When removing CDs from this unit pull them
out horizontally.
• CD-R and CD-RW are easier to damage than
a normal music CD. Use a CD-R or a CD-RW
after reading the caution items on the
package etc.
• Don’t stick tape etc. on the CD.
Also, don’t use a CD with tape stuck on it.
CDs that can’t be used
• CDs that aren’t round can’t be used.
When using a new CD
If the CD center hole or outside rim has burrs,
use it after removing them with a ball pen etc.
• CDs with coloring on the recording surface
or that are dirty can’t be used.
• Don’t use CDs without disc mark
.
Burrs
• A CD-R or CD-RW that hasn’t been finalized
can’t be played. (For the finalization process
refer to your CD-R/CD-RW writing software,
and your CD-R/CD-RW recorder instruction
manual.)
Burrs
CD storage
• Don’t place them in direct sunlight (On the
seat or dashboard etc.) and where the
temperature is high.
CD accessories
Don’t use disc type accessories.
• Store CDs in their cases.
— 6 —
General features
Release button
Power
(KDC-219/KDC-2019V/KDC-2019/
KDC-29MR/KDC-217/KDC-217S only)
AM
FM
Turning ON the Power
ud
4
¢
Press the [SRC] button.
Turning OFF the Power
Press the [SRC] button for at least 1 second.
Selecting the Source
Press the [SRC] button.
Source required
Display
SRC ATT/ #1
LOUD
#3
CLK/
ADJ
Q/
AUD
Tuner
CD
"TUnE"
"CD"
External disc
"DISC"
KDC-219/KDC-2019V/KDC-2019/KDC-29MR/KDC-217/KDC-217S
ATT indicator
(Function of the KDC-219/KDC-2019V/KDC-2019/KDC-29MR)
Standby (Illumination only mode) "OFF"
LOUD indicator
Volume
Increasing Volume
Clock display
Clock display
Clock indicator
Press the [u] button.
SYSTEM Q indicator
Decreasing Volume
KDC-119/KDC-119S
Press the [d] button.
LOUD indicator
Attenuator
Turning the volume down quickly.
Press the [ATT] button.
Each time the button is pressed the Attenuator turns ON or OFF.
When it’s ON, the "ATT" indicator blinks.
ATT indicator
Clock indicator
SYSTEM Q indicator
— 7 —
General features
Loudness
Audio Control
Compensating for low and high tones during low volume.
1 Select the source for adjustment
Press the [LOUD] button for at least 1 second.
Each time the button is pressed for at least 1 second the
Loudness turns ON or OFF.
Press the [SRC] button.
2 Enter Audio Control mode
Press the [AUD] button for at least 1 second.
When it’s ON, "LOUD" indicator is ON.
3 Select the Audio item for adjustment
Press the [FM] or [AM] button.
Each time the button is pressed the items that can be adjusted
switch as shown below.
System Q
You can recall the best sound setting preset for different types of
the music.
4 Adjust the Audio item
Press the [4] or [¢] button.
Adjustment Item
Display
Range
1 Select the source to set
Press the [SRC] button.
Bass level
Middle level
Treble level
Balance
"BAS"
"MID"
"TRE"
"BL"
–8 — +8
–8 — +8
–8 — +8
Left 15 — Right 15
Rear 15 — Front 15
2 Select the Sound type
Press the [Q] button.
Each time the button is pressed the sound setting switches.
Fader
"FD"
Sound setting
Display
5 Exit Audio Control mode
Flat
Rock
Top 40
Pops
Jazz
Easy
"SQ-1"
"SQ-2"
"SQ-3"
"SQ-4"
"SQ-5"
"SQ-6"
"SCAn"
Press the [AUD] button.
Speaker Setting
Fine-tuning so that the System Q value is optimal when setting
the speaker type.
Scan of Flat — Easy
• Each setting value is changed with the <Speaker setting> (page
8).
First, select the speaker type with the Speaker setting.
• When the System Q setting is changed, the Bass, Middle, and
Treble set in audio control replace the System Q values.
1 Enter Standby
Press the [SRC] button.
Select the "OFF" display.
2 Enter Speaker Setting mode
Press the [Q] button.
— 8 —
3 Select the Speaker type
4 Exit clock adjustment mode
Press the [4] or [¢] button.
Each time the button is pressed the setting switches as shown
below.
Press the [CLK] button.
Speaker type
Display
Function of the KDC-219/KDC-2019V/KDC-2019/KDC-29MR/KDC-217/KDC-217S
OFF
"SP-F"
"SP-O"
"SP-6"
"SP-5"
DSI (Disabled System Indicator)
A red indicator will blink on the unit after the faceplate is
removed, warning potential thieves.
For the OEM speaker
For 6 & 6x9 in. speaker
For 5 & 4 in. speaker
1 Turn the power OFF
4 Exit Speaker Setting mode
Press the [SRC] button for at least 1 second.
Press the [Q] button.
2 Set the DSI
While pressing the [#1] and [#3] button, press the [SRC]
button.
Clock Display
Each time the step 1 and 2 operation is done the DSI turns ON or
Press the [CLK] button.
OFF.
Each time the button is pressed the clock display turns ON or
OFF.
When it’s ON, the clock indicator is ON.
Adjusting Clock
1 Select the clock display
Press the [CLK] button.
2 Enter clock adjustment mode
Press the [CLK] button for at least 2 seconds.
The clock display blinks.
3 Adjust the hours
Press the [FM] or [AM] button.
Adjust the minutes
Press the [4] or [¢] button.
— 9 —
General features
Tuner features
Function of the KDC-219/KDC-2019V/KDC-2019/KDC-29MR/KDC-217/KDC-217S
FM/
Theft Deterrent Faceplate
The faceplate of the unit can be detached and taken with you,
helping to deter theft.
AM
CRSC
¢
4
Removing the Faceplate
Press the Release button.
The faceplate is unlocked, allowing you to detach it.
• The faceplate is a precision piece of equipment and can be
damaged by shocks or jolts. For that reason, keep the faceplate in
its special storage case while detached.
• Do not expose the faceplate or its storage case to direct sunlight
or excessive heat or humidity. Also avoid places with too much
dust or the possibility of water splashing.
SRC
#1 - 6
AUTO/
AME
Reattaching the Faceplate
KDC-219/KDC-2019V/KDC-2019/KDC-29MR/KDC-217/KDC-217S
CRSC indicator
1 Align the projections on the unit with the grooves on the
ST indicator
Preset station number
faceplate.
Band display
AUTO indicator
Frequency display
2 Push the faceplate in until it clicks.
KDC-119/KDC-119S
Band display
The faceplate is locked in place, allowing you to use the unit.
CRSC indicator
Preset station number
ST indicator
AUTO indicator
Frequency display
— 10 —
1 Select the band
Tuning Mode
Choose the tuning mode.
Press the [FM] or [AM] button.
2 Select the frequency to put in the memory
Press the [AUTO] button.
Each time the button is pressed the Tuning mode switches as
Press the [4] or [¢] button.
shown below.
3 Put the frequency in the memory
Press the [#1] — [#6] button for at least 2 seconds.
The preset number display blinks 1 time.
On each band, 1 station can be put in the memory on each [#1]
— [#6] button.
Tuning mode
Display
Operation
Auto seek
"AUTO 1"
indicator
"AUTO 2"
indicator
Automatic search for a station.
Preset station
seek
Search in order of the stations
in the Preset memory.
Manual
—
Normal manual tuning control.
Auto Memory Entry
Putting stations with good reception in the memory
automatically.
Tuning
Selecting the station.
1 Select the band for Auto Memory Entry
Press the [FM] or [AM] button.
1 Select tuner source
Press the [SRC] button.
Select the "TUnE" display.
2 Open Auto Memory Entry
Press the [AME] button for at least 2 seconds.
When 6 stations that can be received are put in the memory
Auto Memory Entry closes.
2 Select the band
Press the [FM] or [AM] button.
Each time the [FM] button is pressed it switches between the
FM1, FM2, and FM3 bands.
Preset Tuning
Calling up the stations in the memory.
3 Tune up or down band
Press the [4] or [¢] button.
During reception of stereo stations the "ST" indicator is ON.
1 Select the band
Press the [FM] or [AM] button.
2 Call up the station
Press the [#1] — [#6] button.
Station Preset Memory
Putting the station in the memory.
— 11 —
Tuner features
CD/External disc control features
CRSC (Clean Reception System Circuit)
Temporarily have reception switched from stereo to mono to
reduce multi-path noise when listening to the FM station.
DISC-
DISC+
¢
0
4
Press the [CRSC] button for at least 1 second.
Each time the button is pressed CRSC turns ON or OFF.
When it's ON, the CRSC indicator is ON.
SRC
SCAN
REP M.RDM
RDM
KDC-219/KDC-2019V/KDC-2019/KDC-29MR/KDC-217/KDC-217S
Track number
Disc number
SCN indicator
RDM indicator
Track time
REP indicator
IN indicator
KDC-119/KDC-119S
Track number
RDM indicator
IN indicator
REP indicator
Track time
SCN indicator
— 12 —
Hold down on the [¢] button.
Release your finger to play the disc at that point.
Playing CD
When a CD is inserted
Press the [SRC] button.
Select the "CD" display.
Reversing
Hold down on the [4] button.
Release your finger to play the disc at that point.
When a CD is inserted, the "IN" indicator is ON.
Eject the CD
Track Search
Press the [0] button.
Selecting the song you want to hear.
Press the [4] or [¢] button.
3 in. (8cm) CD cannot be played. Using an adapter and inserting
them into this unit can cause damage.
Function of the KDC-219/KDC-2019V/KDC-2019/KDC-29MR
Playing External Disc
Playing discs set in the optional accessory disc player connected
to this unit.
Function of the KDC-219/KDC-2019V/KDC-2019/KDC-29MR
Album Search (Function of disc changer)
Selecting the disc you want to hear.
Press the [SRC] button.
Select the display for the disc player you want.
Press the [DISC–] or [DISC+] button.
Display examples:
Display
Disc player
Track/Album Repeat
Replaying the song/disc you're listening to.
"CD-2"
"DISC"
"DISC"
CD player
CD changer
MD changer
Press the [REP] button.
Each time the button is pressed the Repeat Play switches as
• Disc #10 is displayed as "0".
• The functions that can be used and the information that can be
displayed will differ depending on the external disc players being
connected.
shown below.
Repeat play
Display
Track Repeat
Album Repeat
"REP" indicator & Track No. blink.
"REP" indicator & Disc No. blink.
(Function of disc changer)
OFF
—
Fast Forwarding and Reversing
Fast Forwarding
— 13 —
CD/External disc control features
When it's ON, the "RDM" indicator is ON and the track and disc
number blink.
Track Scan
Playing the first part of each song on the disc you are listening
to and searching for the song you want to listen to.
When the [¢] button is pressed, the next song select starts.
1 Start Track Scan
Press the [SCAN] button.
"SCN" indicator is ON.
2 Release it when the song you want to listen to is played
Press the [SCAN] button.
Random Play
Playing all the songs on the disc in random order.
Press the [RDM] button.
Each time the button is pressed Random Play turns ON or OFF.
When it's ON, the "RDM" indicator is ON and the track number
blinks.
When the [¢] button is pressed, the next song select starts.
Function of the KDC-219/KDC-2019V/KDC-2019/KDC-29MR
Magazine Random Play
(Function of disc changer)
Play the songs on all the discs in the disc changer in random
order.
Press the [M.RDM] button.
Each time the button is pressed the Magazine Random Play turns
ON or OFF.
— 14 —
Basic Operations of remote
Accessory of the KDC-219/KDC-2019V/KDC-2019
Loading and Replacing the battery
Use one lithium battery (CR2025).
Insert the batteries with the + and – poles aligned properly,
following the illustration inside the case.
4/¢
2WARNING
FM/AM/DISC
38
Store unused batteries out of the reach of children. Contact a doctor
immediately if the battery is accidentally swallowed.
Do not set the remote on hot places such as above the dashboard.
Basic operations
ATT
VOL.
[VOL.] buttons
Adjusting the volume.
SRC
[SRC] button
Each time the button is pressed the source switches.
For the source switching order refer to <Selecting the Source>
(page 7).
[ATT] button
Turning the volume down quickly.
When it is pressed again it returns to the previous level.
— 15 —
Basic Operations of remote
Accessory of the KDC-219/KDC-2019V/KDC-2019
In Tuner source
[FM]/ [AM] buttons
Select the band.
Each time the [FM] button is pressed it switches between the
FM1, FM2, and FM3 bands.
[4]/ [¢] buttons
Tune up or down band.
In Disc source
[4]/ [¢] buttons
Doing track forward and backward.
[DISC+]/ [DISC–] buttons
Doing album forward and backward.
[38] button
Each time the button is pressed the song pauses and plays.
— 16 —
Accessories
External view
External view
......... Number of items
2WARNING
......... Number of items
If you connect the ignition wire (red) and the battery wire (yellow)
to the car chassis (ground), you may cause a short circuit, that in
turn may start a fire. Always connect those wires to the power
source running through the fuse box.
1
2
3
4
5
.........4
.........4
.........1
.........1
.........2
2CAUTION
• If your car's ignition does not have an ACC position, connect the
ignition wires to a power source that can be turned on and off
with the ignition key. If you connect the ignition wire to a power
source with a constant voltage supply, as with battery wires, the
battery may die.
• If the console has a lid, make sure to install the unit so that the
faceplate will not hit the lid when closing and opening.
• If the fuse blows, first make sure the wires aren’t touching to
cause a short circuit, then replace the old fuse with one with the
same rating.
• Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps on
the ends of the unconnected wires or the terminals.
• Connect the speaker wires correctly to the terminals to which
they correspond. The unit may be damaged or fail to work if you
share the - wires or ground them to any metal part in the car.
• When only two speakers are being connected to the system,
connect the connectors either to both the front output terminals
or to both the rear output terminals (do not mix front and rear).
For example, if you connect the + connector of the left speaker
to a front output terminal, do not connect the - connector to a
rear output terminal
(KDC-219/KDC-2019V/KDC-2019/
KDC-217/KDC-217S only)
The use of any accessories except for those provided might result in
damage to the unit. Make sure only to use the accessories shipped with
the unit, as shown above.
Installation Procedure
1. To prevent a short circuit, remove the key from the ignition and
disconnect the - battery.
2. Make the proper input and output wire connections for each unit.
3. Connect the speaker wires of the wiring harness.
• After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
• Mount the unit so that the mounting angle is 30° or less.
4. Connect the wiring harness wires in the following order: ground,
battery, ignition.
5. Connect the wiring harness connector to the unit.
6. Install the unit in your car.
7. Reconnect the - battery.
8. Press the reset button.
— 17 —
Connecting Wires to Terminals
Front left output (White) (KDC-2019V/2019 only) 26
Front right output (Red) (KDC-2019V/2019 only) 27
Rear left output (White) 23
Rear right output (Red) 28
2 KENWOOD disc changer control input (KDC-219/2019V/2019/29MR only)
To connect the Disc changer, consult
your Disc changer manual. 3
REAR
L
Fuse (10A) 24
R
FM/AM antenna input 1
If no connections are made, do not let the wire come out from the tab.
4
Wiring harness
(Accessory1)25
29
White/Black
To front left
speaker 30
6 Connect either to the power control terminal
FRONT • L
P.CONT.OUT
when using the optional power amplifier, or to
Power control/Motor antenna
control wire (Blue/White)
16
White
the antenna control terminal in the vehicle.
ANT.
CONT.
31
32
Gray/Black
To front right
speaker 33
FRONT • R
Gray
34
35
Green/Black
To rear left
speaker 36
REAR • L
Green
37
38
Ignition key
switch
10
Purple/Black
ACC 13
To rear right
speaker 39
REAR • R
Ignition wire (Red) 20
Purple
40
Battery wire (Yellow) 21
Car fuse box
(Main fuse)
11
Car fuse
box 14
Ground wire (Black) · (To car chassis) 22
–
+
Battery 12
— 18 —
Installation
■ Installation
■ Installing in Japanese-Made Cars
1 Refer to the section "Removing the hard rubber frame" (page 20)
Firewall or metal support
and then remove the hard rubber frame.
2 Align the holes in the unit (two locations on each side) with the
vehicle mounting bracket and secure the unit with the accessory
screws.
Screw (M4X8)
(commercially
available)
N
T
8 mm
8mm
MAX.
MAX.
N
T/N
3
T
4
ø5mm
ø5mm
Bend the tabs of the
mounting sleeve
with a screwdriver or
similar utensil and
attach it in place.
T: Toyota cars
N: Nissan cars
Accessory3...for Nissan car
Accessory4 ...for Toyota car
• During installation, do not use any screws except for those provided.
The use of different screws might result in damage to the main unit.
• Damage may occur if a screwdriver or similar tool is used with
excessive force during the installations.
Metal mounting strap
(commercially available)
Self-tapping screw
(commercially available)
Make sure that the unit is installed securely in place. If the unit is
unstable, it may malfunction (for example, the sound may skip).
■ Screwing the Faceplate on the Unit
If you want to fasten the
faceplate to the main unit so
that it does not fall off,
screw in the provided screw
(ø4 X 16 mm) in the hole
shown below.
Accessory5
Never insert the taptite screw (ø4 × 16 mm) in any other screw hole
than the one specified. If you screw it in another hole, it will contact
and may cause damage to the mechanical parts inside the unit.
— 19 —
Installation
■ Removing the hard rubber frame
■ Removing the Unit
1 Refer to the section “Removing the hard rubber frame” and then
1 Engage the catch pins on the removal tool and remove the two
locks on the lower level.
remove the hard rubber frame.
Lower the frame and pull it forward as shown in the figure.
2 Remove the screw (M4 × 8) on the back panel.
3 Insert the two removal tools deeply into the slots on each side,
as shown.
Catch
Lock
Accessory2
Screw (M4X8)
Removal tool
(commercially
available)
Accessory2
Removal tool
2 When the lower level is removed, remove the upper two
locations.
4 Lower the removal tool
toward the bottom, and pull
out the unit halfway while
pressing towards the inside.
Be careful to avoid injury from
the catch pins on the removal
tool.
5 Pull the unit all the way out
with your hands, being
careful not to drop it.
The frame can be removed from the top side in the same manner.
— 20 —
Troubleshooting Guide
What might seem to be a malfunction in your unit may
just be the result of slight misoperation or miswiring.
Before calling service, first check the following table
for possible problems.
? The sound quality is poor or distorted.25
✔
One of the speaker wires is being pinched by a screw in the car.
☞ Check the speaker wiring.
✔
The speakers are not wired correctly.27
☞ Reconnect the speaker wires so that each output terminal is
connected to a different speaker.
General
? The Touch Sensor Tone doesn’t sound.34
? The power does not turn ON.01
✔
The preout jack is being used.
✔
The fuse has blown.
☞ The Touch Sensor Tone can’t be output from the preout jack.
☞ After checking for short circuits in the wires, replace the fuse with
one with the same rating.
Tuner source
✔
No ACC position on vehicle ignition.02
☞ Connect the same wire to the ignition as the battery wire.
? Radio reception is poor.39
✔
✔
The car antenna is not extended.
☞ Pull the antenna out all the way.
? Nothing happens when the buttons are pressed.04
✔
The computer chip in the unit is not functioning normally.
☞ Press the reset button on the unit (page 5).
The antenna control wire is not connected.40
☞ Connect the wire correctly, referring to the section on
<Connecting Wires to Terminals>.
? There’s a source you can’t switch.06
✔
There’s no CD inserted.
☞ Set the media you want to listen to. If there’s no media in this
unit, you can't swhich to each source.
? The memory is erased when the ignition is turned OFF.10
✔
The battery wire has not been connected to the proper terminal.
☞ Connect the wire correctly, referring to the section on
<Connecting Wires to Terminals>.
✔
The ignition and battery wire are incorrectly connected.11
☞ Connect the wire correctly, referring to the section on
<Connecting Wires to Terminals>.
? Even if Loudness is turned ON, high-pitched tone isn't compensated
for. 17
✔
Tuner source is selected.
☞ High-pitched tone isn't compensated for when in Tuner source.
? No sound can be heard, or the volume is low.
✔
The fader or balance settings are set all the way to one side.21
☞ Center the fader and balance settings.
✔
The input/output wires or wiring harness are connected incorrectly.22
☞ Reconnect the input/output wires or the wiring harness correctly.
See the section on <Connecting Wires to Terminals>.
— 21 —
Troubleshooting Guide
Disc source
? Can’t remove disc.64
The cause is that more than 10 minutes has elapsed since the vehicle
✔
? "AVin" is displayed without achieving External disc control mode.50
ACC switch was turned OFF.
✔
✔
O-N switch is set to "O" side.
☞ Set the switch to "N" side.
☞ The disc can only be removed within 10 minutes of the ACC
switch being turned OFF. If more than 10 minutes has elapsed,
turn the ACC switch ON again and press the Eject button.
Unsupported disc changer is connected.51
☞ Connect the supported disc changer. (page 4)
? The disc won’t insert.65
? The specified disc does not play, but another one plays instead.52
✔
There’s already another disc inserted.
✔
✔
✔
The specified CD is quite dirty.
☞ Press the [0] button and remove the disc.
☞ Clean the CD.
? Track Search can't be done.66-2
The CD is upside-down.53
☞ Load the CD with the labeled side up.
✔
For the albums first or last song.
☞ For each album, Track Search can't be done in the backward
direction for the first song or in the forward direction for the last
song.
The disc is loaded in a different slot from that specified.54
☞ Eject the disc magazine and check the number for the specified
disc.
If the following situations, consult your nearest service
center:
✔
The disc is severely scratched.55
☞ Try another disc instead.
• Even though the disc changer is connected, the Disc Changer source is
not ON, with "AVin" showing in the display during the Changer Mode.
• Even though no device (KCA-S210A, CA-C1AX, KDC-CPS87, KDC-CX87,
KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is connected, the
Auxiliary input is entered when switching modes.
? The specified track will not play.58
✔
Random play or magazine random play has been selected.
☞ Turn off random play or magazine random play.
? Track repeat, disc repeat, track scan, random play, and magazine
random play start by themselves.59
✔
The setting is not canceled.
☞ The settings for these functions remain on until the setting to off
or the disc ejected, even if the power is turned off or the source
changed.
? Cannot play CD-R or CD-RW.60
✔
Finalization processing is not being conducted for CD-R/CD-RW.
☞ Conduct finalization processing with CD recorder.
✔
A non-compatible CD changer is being used to play the CD-R/CD-
RW.61
☞ Use a CD changer compatible with CD-R/CD-RW to play.
? A CD ejects as soon as it is loaded.62
✔
The CD is upside-down.
☞ Load the CD with the labeled side up.
✔
The CD is quite dirty.63
☞ Clean the CD, referring to the section on <CD cleaning> (page 6).
— 22 —
E-0d:
The protective circuit in the unit activates when the
temperature inside the automatic disc changer
exceeds 60°C (140°F), stopping all operation.E0d
➪ Cool down the unit by opening the windows or
turning on the air conditioner. As the temperature
falls below 60°C (140°F), the disc will start playing
again.
The messages shown below display your systems
condition.
E-01:
No disc magazine has been loaded in the changer.
The disc magazine is not completely loaded.E01
➪ Load the disc magazine properly.
No CD in the unit.
➪ Insert the CD.
LOAd:
Discs are being exchanged in the Disc changer.E57
E-02:
E-04:
No disc has been loaded in the disc magazine.E02
➪ Load a disc into the disc magazine.
IN (Blink):
The CD player section is not operating properly.E59
➪ Reinsert the CD. If the CD cannot be ejected or the
display continues to flash even when the CD has
been properly reinserted, please switch off the
power and consult your nearest service center.
No disc has been loaded in the disc magazine.E04
➪ Load a disc into the disc magazine.
The CD is quite dirty. The CD is upside-down. The CD
is scratched a lot.
➪ Clean the CD and load it correctly.
E-10:
E-11:
Nothing has been recorded on the MD.E10
No tracks are recorded on the MD, although it has a
title.E11
E-12:
E-77:
The faceplate of the slave unit being connected to
this unit has been removed.E30
➪ Replace it.
The unit is malfunctioning for some reason.E77
➪ Press the reset button on the unit. If the "E-77"
code does not disappear, consult your nearest
service center.
E-99:
The unit is malfunctioning for some reason.E99A
➪ Press the reset button on the unit. If the "E-99"
code does not disappear, consult your nearest
service center.
— 23 —
Specifications
Specifications subject to change without notice.
FM tuner section
Audio section
Frequency range (200 kHz space) ............87.9 MHz – 107.9 MHz
Usable sensitivity (S/N = 30dB) ....................9.3dBf (0.8 µV/75 Ω)
Quieting Sensitivity (S/N = 50dB) ...............15.2dBf (1.6 µV/75 Ω)
Frequency response ( 3 dB).................................30 Hz – 15 kHz
Signal to Noise ratio (MONO)..............................................70 dB
Selectivity ( 400 kHz).......................................................≥ 80 dB
Stereo separation (1 kHz) ....................................................40 dB
Maximum output power
KDC-219/2019V/2019 ................................................50 W x 4
KDC-29MR/217/217S/119/119S.................................45 W x 4
Full Bandwidth Power (at less than 1% THD) ................22 W x 4
Tone action
Bass : ...............................................................100 Hz 10 dB
Middle : ..............................................................1 kHz 10 dB
Treble : .............................................................10 kHz 10 dB
Preout level / Load (during disc play)....................1800 mV/10 kΩ
Preout impedance............................................................≤ 600 Ω
AM tuner section
Frequency range (10 kHz space) ...................530 kHz – 1700 kHz
Usable sensitivity (S/N = 20dB) .............................28 dBµ (25 µV)
General
CD player section
Operating voltage (11 – 16V allowable) ..............................14.4 V
Current consumption.............................................................10 A
Installation Size (W x H x D) ..........................182 x 53 x 157 mm
7-3/16 x 2-1/16 x 6-3/16 inch
Laser diode....................................................GaAlAs (λ=780 nm)
Digital filter (D/A)......................................8 Times Over Sampling
D/A Converter .......................................................................1 Bit
Spindle speed...............................................500 – 200 rpm (CLV)
Wow & Flutter........................................Below Measurable Limit
Frequency response ( 1 dB).................................10 Hz – 20 kHz
Total harmonic distortion (1 kHz) ......................................0.01 %
Signal to Noise ratio (1 kHz) ................................................96 dB
Dynamic range ....................................................................93 dB
Channel separation..............................................................85 dB
Weight...................................................................3.1 lbs (1.4 kg)
— 24 —
|