Kawasaki Drill 690551 1HR User Manual

COMPONENT  
#690551-1HR  
19.2V 2-SPEED BATTERY-OPERATED DRILL  
INSTRUCTION MANUAL  
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,  
MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND  
UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO  
SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.  
FOR CUSTOMER SERVICE  
POUR LE SERVICE APRÉS VENTE  
OU DU CONSOMMATEUR  
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE  
PRODUCT, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE  
DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION  
AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE  
REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU WOULD LIKE TO MAKE  
A SUGGESTION OR COMMENT, GIVE US A CALL OR EMAIL US AT: [email protected].  
YOUR FEEDBACK IS VITAL TO US.  
87-1904-60957  
KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™  
MOTORS CORP., U.S.A., WHICH DOES NOT MANUFACTURE OR  
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE  
DIRECTED TO:  
PARA EL SERVICIO  
PARA EL CONSUMIDOR  
©COPYRIGHT 2006 ALLTRADE TOOLS, LLC.  
1431 VIA PLATA  
LONG BEACH, CA 90810-1462 USA  
1-800-590-3723  
Printed in China  
690551 – 19.2V Green Cordless Drill_Rev 8/26/06  
 
WORK AREA  
DANGER indicates an imminently hazardous  
situation which, if not avoided, will result in death  
or serious injury.  
Keep your work area clean and well lit. Cluttered work benches and dark work  
areas may cause accidents or injury.  
WARNING indicates a potentially hazardous  
situation which, if not avoided, could result in  
death or serious injury.  
Do not operate power tools in explosive areas, such as in the presence of  
flammable liquids, gases or dust. Power tools create sparks which may ignite  
the dust or fumes.  
CAUTION indicates a potentially hazardous  
situation which, if not avoided, may result in  
minor or moderate injury.  
Keep bystanders, children and visitors away while operating a power tool.  
Distractions can cause you to lose control.  
CAUTION used without the safety alert symbol  
indicates a potentially hazardous situation which,  
if not avoided, may result in property damage.  
ELECTRICAL SAFETY  
NOTE provides additional information that is useful  
for proper use and maintenance of this tool. If a  
NOTE is indicated make sure it is fully understood.  
Do not abuse the cord. Never use the cord to carry the tool. Keep the cord  
away from heat, oil, sharp edges, or moving parts. Replace damaged cords  
immediately. Damaged cords may create a fire.  
IMPORTANT SAFEGUARDS  
A battery operated tool with integral batteries or a separate battery pack  
must be recharged only with the specified charger for the battery. A charger  
that may be suitable for one type of battery may create a risk of fire when used with  
another battery.  
People with electronic devices, such as pacemakers, should consult their  
physician(s) before using this product. Operation of electrical equipment in  
close proximity to a heart pacemaker could cause interference or failure of  
the pacemaker.  
Use battery operated tool only with specifically designated battery pack. Use of  
any other batteries may create risk of fire.  
WARNING: Some dust created by power sanding, sawing, grinding, drilling and  
other construction activities contains chemicals known to the State of California  
to cause cancer, birth defects or other reproductive harm.  
PERSONAL SAFETY  
Some examples of these chemicals are:  
• Lead from lead-based paints.  
Stay alert, watch what you are doing, and use common sense when operat-  
ing a power tool. Do not use tool while tired or under the influence of drugs,  
alcohol or medication. A moment of inattention while operating power tools  
may result in serious personal injury.  
• Crystalline silica from bricks and cement and other masonry products,  
and arsenic and chromium from chemically-treated lumber.  
Your risk from these exposures varies, depending on how often you do this type  
of work. To reduce your exposure to these chemicals: work in a well ventilated  
area, and work with approved safety equipment, such as dust masks that are  
specially designed to filter out microscopic particles.  
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.  
Keep your hair, clothing, and gloves away from moving parts. Loose clothes,  
jewelry or long hair can be caught in moving parts.  
Avoid accidental starting. Be sure switch is in the locked or “OFF” position  
before inserting battery pack. Carrying power tools with your finger on the switch  
or inserting battery pack into a tool with the power switch “ON” invites accidents.  
WARNING: Handling the power cord on corded products may expose you to  
lead, a chemical known to the State of California to cause cancer and birth  
defects or other reproductive harm. Wash hands after handling.  
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.  
4
 
SERVICE  
Tool service must be performed only by qualified repair personnel. Service or  
maintenance by unqualified personnel may result in a risk of injury.  
Remove adjusting keys or wrenches before turning the tool “ON”. A wrench or a  
key that is left attached to a rotating part of the tool may result in personal injury.  
When servicing a tool, use only identical replacement parts. Follow instructions  
in the Maintenance section of this manual. Use of unauthorized parts or failure to  
follow Maintenance Instructions may create a risk of shock or injury.  
Do not overreach. Keep proper footing and balance at all times. Proper foot-  
ing and balance enable better control of the tool in unexpected situations.  
Use safety equipment. Always wear eye protection. Dust mask, non-skid safe-  
ty shoes, hard hat, or hearing protection must be used for appropriate conditions.  
SPECIFIC SAFETY RULES AND/OR SYMBOLS  
TOOL USE AND CARE  
Hold tool by insulated gripping surfaces when perform-  
ing an operation where the cutting tool may contact hidden wiring. Contact  
with a “live” wire will also make exposed metal parts of the tool “live” and shock  
the operator.  
Use clamps or other practical ways to secure and support the workpiece to a  
stable platform. Holding the work by hand or against your body is unstable and  
may lead to loss of control.  
SAFETY RULES FOR CORDLESS DRILL / DRIVERS  
Do not force tool. Use the correct tool for your application. The correct tool  
will do the job better and safer at the rate for which it is designed.  
Always wear safety goggles or eye protection when using this tool. Use a  
dust mask or respirator for applications which generate dust.  
Do not grasp the tool or place your hands too close to the spinning chuck or  
drill bit. Your hand may be lacerated or may cause injury.  
Secure the material being worked on. Never hold it in your hand or across  
your legs. Unstable support can cause loss of control and injury.  
Position yourself to avoid being caught between the tool or side handle and  
walls or posts. Should the socket or bit become bound in the work, the  
reaction torque of the tool could crush your hand or leg.  
Check to see that keys and adjusting wrenches are removed from the  
Cordless Drill before switching the tool “ON”. Keys or wrenches can fly away  
at high velocity striking you or a bystander.  
Do not use the tool if the power switch does not turn it “ON” or “OFF”. A tool that  
cannot be controlled with the switch is dangerous and must be repaired.  
Disconnect battery pack from tool or place the switch in the locked or “OFF” posi-  
tion before making any adjustments, changing accessories, or storing the tool.  
Such preventative safety measures reduce the risk of starting the tool accidentally.  
Store idle tools out of reach of children and other untrained persons. Tools  
are dangerous in the hands of untrained users.  
When battery pack is not in use, keep it away from other metal objects like:  
paper clips, coins, keys, nails, screws, or other small metal objects that can  
make a connection from one terminal to another. Shorting the battery termi-  
nals together may cause sparks, burns or a fire.  
When using the Cordless Drill, always maintain a firm grip on the tool with both  
hands.  
Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained  
tools with sharp cutting edge are less likely to bind and are easier to control.  
Keep the handle of the Cordless Drill dry, clean, and free from oil and grease.  
Do not run the Cordless Drill while carrying it at your side. A spinning  
socket or bit could become entangled with clothing and injury may result.  
Check for misalignment or binding of moving parts, breakage of parts, and any  
other condition that may affect the tool’s operation. If damaged, have the tool  
serviced before using. Many accidents are caused by poorly maintained tools.  
Use only accessories that are recommended by the manufacturer for your  
model. Accessories that may be suitable for one tool may create a risk of injury  
when used on another tool.  
Disconnect the plug or remove the battery pack from tool and place the switch  
in the locked or “OFF” position before making any assembly adjustments,  
changing accessories, performing any inspection, maintenance or cleaning  
procedures. Such preventive safety measures reduce the risk of starting the  
tool accidentally.  
5
6
 
FUNCTIONAL DESCRIPTION  
8
6
10  
Do not use the Cordless Drill if it has been damaged, left outdoors in the  
rain, snow, wet or damp environments, or immersed in liquid.  
5
Maintain labels and nameplates on the Cordless Drill. These carry important  
information. If unreadable or missing, contact Alltrade for a replacement.  
12  
SYMBOLS  
7
3
9
IMPORTANT: Some of the following symbols may be used on your tool. Please  
study them and learn their meaning. Proper interpretation of these symbols will  
allow you to operate the tool better and safer.  
11  
2
SYMBOL  
NAME  
Volts  
Amperes  
Hertz  
Watt  
Kilograms  
Alternating Current  
Direct Current  
EXPLANATION  
Voltage (Potential)  
Current  
Frequency (Cycles per Second)  
Power  
Weight  
Type of Current  
Type of Current  
V
A
Hz  
W
Kg  
4
1
CONTROLS AND COMPONENTS:  
1. Battery Pack  
2. Release Buttons on Each Side  
3. Charger  
4. Indicator Lights  
5. 12.7mm (1/2") Keyless Chuck  
6. 22 Adjustable Torque Settings  
Control Ring  
7. Forward/Reversing and  
Trigger Lock Lever  
8. High/Low Speed Switch  
9. Variable Speed Controlled  
Trigger Switch  
10. Accessory/Bit Holder  
11. Comfort Rubber Grip  
Alternating or Direct Current Type of Current  
Earthing Terminal  
Class II Construction  
Minutes  
Grounding Terminal  
Denotes Double Insulation  
Time  
Time  
ACCESSORIES:  
min  
s
12. Double Ended Screwdriver Bits (2)  
Seconds  
Diameter  
Size of Drill Bits,  
Grinding Wheels, etc.  
No load speed  
Revolutions per Minute  
No-load Rotational Speed  
Revolutions, Surface Speed,  
Strokes, etc. per Minute  
COMPONENT  
BATTERY PACK  
CHARGER  
12.7mm (1/2") KEYLESS CHUCK  
MODEL NUMBER  
.../min  
690549  
690543  
690552  
1,2,3, …  
Ring Selector Settings  
Speed, Torque or Position Settings  
7
8
 
BATTERY  
REMOVING/ATTACHING BATTERY PACK  
REMOVE BATTERY PACK:  
1. Press both release buttons on either  
side of the Cordless Drill to release  
the battery pack.  
Before using battery pack, please read carefully all instruc-  
tions and cautionary markings on battery pack, battery  
charger and product using battery.  
2. Pull battery pack free of Cordless Drill.  
®
Do not incinerate the battery pack even if it is severely dam-  
aged or is completely worn out. The battery pack can explode.  
ATTACH BATTERY PACK:  
1. Align the raised portion of the battery  
pack with the groove in the battery  
compartment of the Cordless Drill.  
Do not carry battery packs in aprons, pockets, or tool  
boxes, product kit boxes, drawers, etc. with loose metal objects. Battery  
pack terminals could be short circuited causing damage to the battery pack,  
severe burns or fire.  
2. Press the battery pack  
into place. Make sure the  
latches are securely fastened.  
Do not use the Cordless  
Drill if the battery pack is  
not seated properly.  
RELEASE BUTTON  
The battery pack is Nickel-Cadmium (Ni-Cad) and is considered to be a toxic  
material by the Environmental Protection Agency. Before disposing of dam-  
aged or worn out Ni-Cad battery packs, check with your State Environmental  
Protection Agency to find out about special restrictions on the disposal of these  
battery packs, take them to your local recycling center for proper disposal, or  
call 1-800-822-8837.  
CHARGER  
Before using battery charger, please read carefully all  
instructions and cautionary markings on battery charger, battery pack and  
product using battery.  
The battery is not fully charged. Before first use, the battery pack requires  
3-5 hours charge time to be fully charged. Subsequent recharging needs 1 hour  
for the battery to be fully charged.  
Use only the charger which accompanied your product or direct replacement as  
listed in this manual. Do not substitute any other charger. Use only Alltrade  
approved chargers with your product.  
Always switch to a fresh battery when tool performance begins to diminish.  
Severe heat is most destructive to a battery; the more heat generated, the faster  
the battery loses power. A battery that gets too hot can have a shortened life.  
Do not disassemble charger.  
Never over-discharge a battery by using the tool even after tool performance  
has decreased. Do not attempt to discharge a tool’s battery by continuing to  
pull on the tool trigger. When tool performance begins to diminish, stop the tool  
and recharge the battery for optimal performance.  
Do not use charger if it has been damaged, left outdoors in the rain, snow, wet  
or damp environments, or immersed in liquid.  
The battery pack and charger heat during charging. Place the charger on a flat,  
non-flammable surface away from flammable materials with at least four inches of  
clearance to allow proper air circulation around the charger and battery pack.  
Charge battery pack at ambient temperatures between 50° F – 104° F.  
Store tool and battery pack in locations where temperatures will not exceed  
120°F. This is important to prevent serious damage to the battery cells.  
The battery pack should always be recharged when the Cordless Drill begins to  
run slowly.  
When the battery pack requires recharging, a 1 hour charge allows the tool to  
operate at full power. A charging indicator light on the charger will illuminate to  
show that charging is taking place.  
When battery pack is not in use, keep it away from other metal objects such as  
paper clips, coins, keys, nails, screws or other small metal objects that can  
make a connection from one terminal to another. Shorting the battery terminals  
together may cause sparks, burns, or fire.  
10  
 
CHARGING BATTERY PACK  
ASSEMBLY  
CHARGE BATTERY PACK:  
1. Plug the charger into  
the nearest 120 volt  
electrical outlet.  
BATTERY PACK  
Be aware that this tool is always in an operating condition  
because it does not have to be plugged into an electrical outlet. Always turn  
the switch “OFF” and remove the battery pack before changing bits.  
2. Make sure the trigger  
on the Cordless Drill  
is in the “OFF”  
INSTALLING DRILL BIT INTO KEYLESS CHUCK  
LED  
LIGHT  
position and remove  
the battery pack from  
the Cordless Drill.  
WARNING  
Before inserting a drill bit or other accessory, make sure the forward/reverse  
and trigger lock lever is in the center “OFF” position to prevent accidental starts  
that may result in injury.  
3. Insert the battery pack  
into the charger. Be sure  
that the battery pack is  
fully seated in the charger.  
Do not force.  
BATTERY  
CHARGER  
Do not attempt to tighten drill bits (or any other accessory) by gripping the  
front of the chuck and turning the tool on. This may cause personal injury  
and/or damage to the chuck.  
4. The red indicator light should come “ON” indicating that the battery pack is in  
a “Fast Charge” mode. If the green indicator light comes “ON”, then the battery  
is already fully charged.  
When removing the bit from the tool, avoid contact with skin and use proper  
protective gloves when grasping the bit or accessory. Accessories may be hot  
after prolonged use.  
5. After approximately one hour of charging, the red indicator light should go  
“OFF” and the green light should come “ON” indicating that the battery is fully  
charged and the charger is now in a “Trickle Charge” mode.  
1. Hold the rear end of the chuck  
in one hand and use the other  
hand to rotate the front end in a  
counterclockwise direction to  
open the jaws of the chuck.  
HOLD  
LOOSEN  
TIGHTEN  
6. The battery can be left in a “Trickle Charge” mode until ready to use.  
IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES  
When using your Cordless Drill continuously, the batteries in your battery pack  
will become hot. You should let a hot battery pack cool down for approximately  
30 minutes before attempting to recharge. When the battery pack becomes  
discharged and is hot, the red light on the charger will flash. When the battery  
pack cools down, the red light will glow continuously to indicate fast charging  
mode, 1-hour charge time.  
2. Insert the shank of the bit (or  
other accessory) fully into the  
keyless chuck, taking care to  
keep the bit in the center of  
the jaws of the chuck.  
3. Turn the front end of the chuck clockwise to hold the bit in place.  
4. Tighten securely by turning the front end of the chuck clockwise while holding  
the rear end.  
This will occur when continuous use of your Cordless  
Drill causes the battery pack to become hot. It does not occur under normal  
circumstances.  
OPERATING THE DRILL  
Never tape the trigger switch down to provide continu-  
ous high speed. The tool may fail under such conditions causing fire or  
personal injury.  
12  
 
CONTROL RING  
THE CONTROL RING ADJUSTS THE LEVEL OF TORQUE:  
• For light duty work, use lower settings.  
VARIABLE SPEED TRIGGER SWITCH  
THIS TOOL IS CONTROLLED  
• For heavy duty work, use higher settings.  
BY A TRIGGER SWITCH:  
PROPER SETTING FOR DRIVING SCREWS:  
1. Set the ring on the lowest  
setting to begin.  
• The speed of the Cordless Drill depends  
on the amount of pressure you put on the  
trigger.  
TRIGGER  
SWITCH  
2. Try tightening the first screw.  
If the drill drives smoothly,  
proceed with the next screw.  
• The more pressure you apply, the faster  
the Cordless Drill will go.  
• Release the pressure and the Cordless Drill  
will slow down.  
3. If the Drill’s clutch slips,  
increase the torque setting  
and try again until the Drill  
drives the screw without incident.  
FORWARD/REVERSE AND TRIGGER LOCK LEVER  
HIGH/LOW SPEED (GEAR) SHIFTING  
LOW SPEED  
HIGH SPEED  
FOR LOW SPEED SETTING:  
• Slide the switch on top of the  
Drill to Position 1 for high  
torque applications and driving  
screws.  
Be sure the trigger is released when changing the position of the lever.  
Always store the tool in the “LOCKED/OFF” position.  
Always check the direction of the Cordless Drill's rotation before use.  
FOR HIGH SPEED SETTING:  
• Slide the switch to Position 2  
for light duty projects.  
TO SELECT THE DIRECTIONS  
OF ROTATION:  
• To select forward Cordless Drill  
rotation, press the trigger lock  
from left to right flat against the Cordless  
Drill body.  
TRIGGER  
LOCK  
• To select reverse, press the trigger lock  
lever in the opposite direction.  
• The center position locks the tool.  
SCREWDRIVING  
WHEN DRIVING FASTENERS:  
• Always start slowly and gradually increase the speed of the Drill.  
TORQUE SETTINGS  
• Release the trigger when you feel the clutch slip.  
To prevent damaging the tool or driving screw too deep  
into work piece, release the trigger when you feel the clutch slip.  
• Always keep the driver bit straight to prevent damage to the screw.  
• Hold the Drill with both hands to ensure control if the bit should stick or slip.  
• To prevent wood from splitting, drill pilot holes into the wood before driving  
in the screws.  
13  
14  
 
• Never try to start a stalled Drill by clicking the trigger switch “ON” and “OFF”.  
This may damage your tool.  
DRILLING METAL  
WHEN DRILLING HARD METALS:  
• To reduce jamming, always keep the Drill running when pulling the bit out of a  
finished hole.  
• Apply a lubricant, such as cutting oil, to the tip of the bit.  
• Start with a small hole then enlarge to the required size. Make sure the bit is  
actually cutting and not spinning in the hole as this will dull the edges of the bit.  
SCREWDRIVING:  
• Always use the correct type and size of screwdriver bit.  
• Keep enough pressure on the bit to keep it drilling through the material.  
• If screws are difficult to tighten, try applying a small amount of washing liquid or  
soap as a lubricant.  
DRILLING MASONRY  
WHEN DRILLING MASONRY:  
• Masonry can be brittle so be careful not to apply too much pressure and crack  
the material.  
• Always hold the tool and screwdriver bit in a straight line with the screw.  
MAINTENANCE AND CLEANING  
• Apply enough pressure to keep the bit cutting and not spinning in the hole as this  
will dull the edges of the bit.  
Always remove the battery pack before attempting  
cleaning or maintenance.  
• Bricks and similar soft materials will require less pressure, concrete will require  
much more.  
This Cordless Drill is lubricated before it leaves the  
factory. This lubrication should last for the life of the tool. No further  
lubrication is required.  
DRILLING WOOD  
Use twist bits to drill holes in wood. Make sure the bits are sharp. Pull the bits  
out of the hole frequently to clear chips from the flutes as an overburdened bit  
may overheat.  
Use only mild soap and a damp cloth to clean the tool. Never let any liquid get  
inside the casing. Never immerse any part of the tool in a liquid. Always keep the  
ventilation openings clear.  
HINTS FOR OPTIMUM USE  
Always clean the battery pack using only a dry cloth. Do not use liquids.  
Always unplug the charger before cleaning it.  
DRILLING:  
• Keep the right amount of pressure in a straight line with the drill bit. Too little and  
the bit will spin without cutting, too much and the motor may stall.  
Regularly clean the ventilation slots in your tool and charger using only a soft  
brush or dry cloth.  
• Just before the drill tip breaks though the other side of the work piece drill more  
slowly and decrease pressure on the tool. This will prevent stalling and leave a  
cleaner hole.  
Never open the Cordless Drill case, battery pack or charger. Do not attempt to  
repair the Cordless Drill, battery pack or charger yourself. Opening any of these  
parts will void your warranty.  
• Use a block of wood to back up work pieces that may splinter.  
• Use spade bits when drilling large diameter holes in wood.  
• Use HSS drill bits when drilling in metal.  
• Use masonry bits when drilling in soft masonry.  
• Use a lubricant when drilling metals other than cast iron, aluminum, copper,  
and brass.  
• When drilling, start the hole slowly, allowing the bit to drill deep enough to prevent  
slipping at higher speeds.  
15  
 
ACCESSORIES  
PROTECTING THE ENVIRONMENT  
Use only accessories that are recommended by the manufacturer for your model.  
Accessories that may be suitable for one tool may become hazardous when used on  
another tool.  
BATTERIES  
Alltrade batteries can be recharged many times. At the end of their useful life,  
recycle batteries with due care for our environment.  
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.  
Ni-Cad and Ni-MH batteries are recyclable. Take them to your local recycling center  
or call 1-800-822-8837. Collected batteries will be recycled or disposed of properly.  
If you must use an extension cord, be sure that the gauge is large enough to carry  
the amount of current necessary for your power tool. If not, your tool may experi-  
ence a loss of power, excessive voltage drop or overheating. The smaller the gauge  
number, the heavier the cord (see table below).  
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS  
Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would  
like further information on the following products, please contact Alltrade Customer  
Service Department at 1-800-590-3723.  
RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS  
TOOL CURRENT RATING  
CONDUCTOR SIZE IN A.W.G  
Cordless Drills/Screwdrivers  
Impact Wrenches  
Sanders  
AMPERE  
3-6  
6-8  
8-10  
10-12  
12-16  
16-20  
10FT.  
18  
18  
18  
16  
25FT.  
18  
18  
18  
16  
50FT.  
18  
18  
18  
14  
100FT.  
18  
16  
14  
14  
-
Jigsaws  
Circular Saws  
14  
12  
12  
12  
12  
12  
Angle Grinders  
-
Reciprocating Saws  
Routers  
SPECIFICATIONS  
Rotary Tools  
SPECIFICATIONS  
Voltage  
Low Speed  
High Speed  
Torque Settings  
Corded and Cordless Multi-Purpose Tools  
Wide Range of Accessories and more  
19.2V  
0-440/min.  
0-1500/min.  
21+ Drill  
Chuck Capacity (max)  
Charger Input  
13mm (1/2")  
120V  
60Hz  
Charging Time  
Battery Type  
Approx. 1 hour  
Ni-Cad  
17  
18  
 
to determine whether any item or part is nonconforming and, if so, whether the  
item and/or part will be repaired and/or replaced. If the unit is repaired, new or  
reconditioned replacement parts may be used. If Alltrade chooses to replace  
the product, it may replace it with a new or reconditioned one of the same or  
comparable design. The repaired or replaced unit will be warranted under the terms  
of the remainder of the warranty period. Typically, a defective product that is  
returned within the first 30 days after the purchase date will be replaced; for items  
returned after the first 30 days and within the warranty period, covered defective  
parts not subject to normal wear and tear or other exclusions will be repaired or  
replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsi-  
ble for the return shipping charges. Alltrade’s repair and/or replacement of any non-  
conforming item and/or part thereof shall constitute fulfillment of all  
obligations to the purchaser. Alltrade shall not be responsible or liable for any  
expense, including freight charges, or repairs made outside Alltrade’s facility, unless  
expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade  
bear any responsibility for loss of the unit, loss of time or rental, inconvenience,  
commercial loss or consequential damages.  
3 YEAR LIMITED WARRANTY  
Express and Exclusive Limited Warranty to Original Retail Buyer  
Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail  
purchaser of the accompanying KAWASAKI™ power tool and no one else all parts  
of the product (except those parts referred to below which are specifically exclud-  
ed from such warranty (see Exclusions)) to be free from defects in materials and  
workmanship for a period of three years from original date of purchase, except that  
such warranty with regard to the battery shall be for a period of two years from  
original date of purchase, unless the tool is used for commercial or rental  
purposes.  
SPECIAL WARRANTY NOTE FOR COMMERCIAL OR RENTAL USE: The above  
warranty for this Kawasaki™ power tool, including the battery, shall be effective for  
only 90 days from the original date of purchase if this tool is used for any  
COMMERCIAL OR RENTAL PURPOSE.  
The date of purchase shall be the date of shipment to the original purchaser, or the  
date the original purchaser took possession, custody or control of the product,  
whichever occurred first. This warranty shall be null and void if the product or any  
component thereof is modified or altered. This warranty does not apply to any  
other product and/or component thereof manufactured or distributed by Alltrade,  
and does not apply to products and/or components thereof designed, manufactured  
and/or assembled by others, for which Alltrade makes no warranties whatsoever.  
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON  
THE FACE HEREOF.  
Exclusions  
This warranty does not cover parts damaged due to normal wear, abnormal  
conditions, misapplication, misuse, abuse, accidents, operation at other than  
recommended pressures or temperatures, improper storage or freight damage.  
Parts damaged or worn by operation in dusty environments are not warranted.  
Failure to follow recommended operating and maintenance procedures also  
voids warranty.  
This limited warranty does not apply to accessory items such as drill bits,  
screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding  
sheets and other related items.  
Warranty Performance  
By purchasing the product, purchaser expressly acknowledges and agrees that their  
sole and exclusive remedy under this warranty shall be strictly limited to the repair  
or replacement of any covered nonconforming items or parts thereof provided that  
any such nonconforming item and/or part is promptly returned to Alltrade’s facility  
postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair,  
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #1-800-590-3723)  
within the applicable warranty period, with a written request by purchaser that  
Alltrade repair and/or replace the nonconforming item and/or part. We recommend  
that you keep the original product packaging in the event you need to ship the unit.  
We suggest the package be insured against loss or in transit damage. When  
sending your product include your name, address, phone number, dated proof  
of purchase (or copy), and a statement about the nature of problem. Warranty  
coverage is conditioned upon purchaser furnishing Alltrade with adequate written  
proof that they are the original purchaser and of the original purchase date. Parts  
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will  
be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if  
found to be defective and subject to warranty. Alltrade retains the sole discretion  
DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,  
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS  
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY,  
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES,  
COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO  
PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS  
WARRANTY.  
Alltrade will not be liable for the following: labor charges, loss or damage resulting  
from improper operation, maintenance or repairs made by other persons;  
pre-delivery services such as assembly, oil or lubricants, and adjustment;  
maintenance services that are normally required to maintain the product.  
The use of other than genuine Alltrade Repair Parts will void warranty.  
19  
20  
 
Warranty Disclaimers  
REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH  
DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,  
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL  
ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF  
THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF  
THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY  
PERIODS SPECIFIED ABOVE.  
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES,  
GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY  
PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR  
REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING  
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE  
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF  
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,  
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY  
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE  
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE  
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY  
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR  
CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S  
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.  
Limitations on Warranty Disclaimers  
Some states do not allow limitations on how long an implied warranty lasts  
and some states do not allow the exclusion or limitation of the incidental or  
consequential damages, so part or all of the above limitations or exclusions may not  
apply to you. This warranty gives you specific legal rights, and you may also have  
other rights which vary from state to state.  
If your product is not covered by this warranty, please call our Customer Service  
Department toll free at 1-800-590-3723 for general repair information and charges.  
EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE  
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR  
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE  
WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR  
IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE  
AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE,  
PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT  
THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,  
GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY  
OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF  
ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING  
BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE  
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY  
EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.  
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH  
WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING  
THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE  
REMEDY IS AS STATED ABOVE.  
Limitation Of Liability  
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR  
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY  
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH  
OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS  
REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER,  
AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR  
OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS  
21  
22  
 

InFocus Projector AA0021 User Manual
Intel Computer Hardware AW8D User Manual
Intel Power Supply ERP2U User Manual
Ironman Fitness Elliptical Trainer 125E User Manual
Jacuzzi Landscape Lighting GQ99000 User Manual
John Deere Impact Driver AT 3107 J User Manual
Kidde Carbon Monoxide Alarm KN COB DP H User Manual
Kompernass Clock Radio KH 2271 User Manual
Kompernass Stereo System KH 2309 User Manual
Korg Musical Instrument GT 120 User Manual