Kambrook Vacuum Cleaner KVC20 User Manual

Jaguar  
Vacuum Cleaners  
 
KVC20/21/22  
Issue 1/05  
Features of your Kambrook JaguarVacuum (KVC22 shown)  
15  
19  
12  
11  
9
14  
7
8
1
13  
5
6
16  
17  
2
18  
3
20  
10  
4
1. Hose inlet connection point  
2. Cord rewind foot pedal  
3. On/off foot pedal  
11. Motor protection filter (not shown)  
12. 360 degree crush proof hose  
13. Telescopic wand  
4. Park tool  
14. Turbo floor head (KVC22 only)  
5. On board tool storage lid release lever 15. Hard floor brush (KVC21 only)  
6. On board tool storage compartment  
7. Dust bag compartment  
16. Crevice tool & brush attachments  
17. Variable power control  
18. Cord storage outlet  
19. Carry handle  
8. Dust bag full indicator  
9. Dust bag compartment opening  
10. HEPA filter (KVC21/22)  
20. Multi terrain floor tool  
4 stage filter (KVC20)  
3
 
To retract the cord push down on the  
‘cord rewind’ pedal.  
UsingYour Kambrook Jaguar  
Vacuum Cleaner  
IMPORTANT: HOLDTHE PLUG  
END WHEN RETRACTINGTHE  
CORDTO PREVENT IT FROM  
STRIKINGYOU ORTHEVACUUM.  
Remove all packaging from the unit, hose  
and other accessories; ensure that you  
have removed all of the accessories before  
discarding the packaging.  
ALWAYS ENSURETHATTHE  
DUST BAG ANDTHE MOTOR  
PROTECTION FILTER ARE  
CORRECTLY FITTED. NEVER  
OPERATE WITHOUTTHE DUST  
BAG OR FILTERS IN PLACE.  
Ensure that the dust bag and filters are  
correctly fitted.  
Locate the crush proof hose and push the  
connection point into the hose inlet  
connection on the top of the unit, until a  
“click” sound is heard.  
Connect the wide end of the metal wand  
to the hose end, and push together firmly.  
Variable Power Control  
The variable power control slide switch is  
located on the top of the vacuum cleaner.  
Slide the control to the right for  
Fit the floor tool to the narrow end of  
the wand/s and push together firmly.  
maximum power for vacuuming hard floor  
and carpet surfaces. Slide the control to  
the left at the minimum power level when  
using the crevice and brush tools.  
Fully extend the power cord by pulling  
the power plug (situated at the rear of the  
unit) out from the unit, until the  
red/yellow tape on the cord is shown.  
Crevice and brush tool  
accessories  
ENSURETHATYOU DO NOT  
OVER EXTENDTHE POWER  
CORD – DO NOT EXTEND PAST  
THE RED/YELLOW WARNING  
TAPE ONTHE CORD  
The crevice tool is ideal for vacuuming  
hard to reach places such as the edges  
along skirting boards.  
Plug into a 230/240v power point and  
switch the power on.  
The brush tools can be used to vacuum  
delicate surfaces and areas such as shelves  
and venetian blinds.  
To commence vacuuming push down on  
the on/off foot pedal, at the top, rear of  
the unit.  
Set the variable temperature control  
between minimum and medium power  
when using the tool accessories.  
When vacuuming is complete, push down  
on the ‘on/off’ pedal to switch off.Turn  
the power off at the outlet and then  
remove the power cord from the power  
outlet (when removing plug from the  
power outlet grasp the plug not the cord).  
Separate crevice and brush tools are  
located inside the on-board tool storage  
compartment.The opening for this  
compartment is located directly below the  
hose connection inlet.To open place a  
4
 
HINT: once the bag is inserted ‘puff-out’ the bag as  
much as possible to ensure the full capacity of the  
bag can be taken up.  
finger inside the thumb groove and pull  
the compartment lid upwards.  
Turn off the vacuum cleaner when  
changing any attachments.  
When vacuuming fine dust particles, the  
fine dust particles can clog the pores of  
the dust bag and the dust bag indicator  
will indicate full. If this happens the bag  
could appear relatively empty, however  
the bag will still need to be changed to  
avoid strain on the motor.  
Dust bag indicator and  
changing the dust bag  
The dust bag should be changed when full.  
The dust bag indicator window will  
gradually turn red as the bag fills up and  
when the dust bag indicator displays ‘red’  
it is time to change the dust bag.  
NOTE:The bag compartment lid may not close if  
the bag is not correctly fitted.  
IMPORTANT: DO NOT USETHE  
UNIT WITH OUT A DUST BAG  
IN PLACE  
Always switch appliance off, then switch off  
at the power outlet and unplug the appliance  
prior to replacing dust bags or filters.  
To remove the dust bag, ensure the unit is  
down on its wheels, remove the crush  
proof hose and push the ‘Dust bag  
compartment lid release lever’ underneath  
the handle. Once the lid has released, pull  
the top cover back.  
Replacing filters  
Filters must be cleaned from time to time  
to remove the fine dust particles that have  
been collected.This can be done by shaking  
them; however after approximately 5 dustbag  
changes the filters should be replaced.  
To remove the bag, grasp the top of dust bag  
and pull out, and dispose in a rubbish bin.  
Motor protection filter  
The motor protection filter must always  
be in place when operating the vacuum  
otherwise damage to the motor may occur  
To place a new dust bag, take a fresh dust  
bag and with the arrow (printed on the  
material section of the dust bag) pointing  
down slide the material down into the  
dust bag holder, until it comes in contact  
with the bottom of the holder.  
To replace the motor protection filter –  
Remove the dustbag or pull the bag  
forward.The motor protection filter is  
located at the rear, right hand side of this  
inner chamber. Pull the plastic filter holder  
upward to remove.  
HEPA filter  
Filter holder  
Filter holder  
Dust bag holder  
Removable filter  
5
 
Care and Maintenance  
Always switch appliance off, then switch  
off at the power outlet and then unplug  
the appliance prior cleaning or replacing  
either filter.  
To clean the outside of the unit, wipe the  
exterior with a soft, damp cloth. Never  
use an abrasive cleaner.  
Check and replace both the motor  
protection and HEPA dust filters on a  
regular basis.  
From time to time hair, cotton and other  
items may get caught in the brushes of the  
floor head.To remove such items, take a  
pair of scissors and cut across the cotton,  
hair, etc to loosen, then gently pull to  
remove.  
NOTE: Do not continue to pull if the item/s does  
not easily come out as this may permanently  
damage the floor tools.  
The Turbo brush (KVC22 only) should be  
cleaned regularly for optimum performance.  
Without regular cleaning the turbo head  
may block and restrict the rapid  
movement of the bristles.To clean the  
bristles, take a pair of scissors and cut  
across the cotton, hair, etc to loosen, then  
gently pull to remove.  
6
 
KAMBROOK  
2YEAR REPAIR  
WARRANTY  
KAMBROOK warrants the purchaser  
If the product includes one or a number of  
against defects in workmanship and material, accessories only the defective accessory  
for a period of 2 years from the date  
of purchase (3 months commercial use).  
or product will be replaced.  
In the event of KAMBROOK choosing to  
replace the appliance, the guarantee will  
expire at the original date, ie. 12 months  
from the original purchase date.  
Guarantee and purchase receipt for this  
product are to be retained as proof  
of purchase and must be presented  
if making a claim under the terms of the  
KAMBROOK guarantee.  
In Australia, this KAMBROOK Guarantee  
is additional to the conditions and  
guarantees which are mandatory as  
implied by the Trade Practices Act 1974  
and State Territory legislation.  
KAMBROOK reserves the right to repair  
the appliance within the warranty period.  
Warranty does not apply to any defect,  
deterioration, loss or injury or damage  
occasioned by, or as a result of the misuse  
or abuse, negligent handling or if the product  
has not been used in accordance with the  
instructions. Items subject to wear and  
tear, such as filters, accessories and drive  
belts, are not covered by this warranty.  
The guarantee excludes breakages and  
consumables.  
For service, spare parts or product  
information in Australia, please call  
KAMBROOK on the customer Service  
Line (free call) 1800 800 634.  
For service, spare parts or product  
information in New Zealand,  
please call KAMBROOK New Zealand,  
Greenmount, Auckland Phone 09 271 3980  
Fax 0800 288 513. For spare parts phone  
09 271 3980.  
This warranty is void if there is evidence  
of the product being tampered with by  
unauthorised persons.  
If claiming under this guarantee the product  
must be returned to freight prepaid.  
YOUR PURCHASE RECORD (Please complete)  
Attach purchase receipt here.  
DATE OF PURCHASE___________________________
MODEL NUMBER _____________________________
SERIAL NUMBER (If applicable) ___________________
Please don’t return purchase record  
unless you are making a claim  
PURCHASED FROM ___________________________
 
Kambrook 461 Plummer Street, Port Melbourne 3207, Australia  
Customer Service Line (free call) 1800 800 634 Customer Service Fax 1800 621 337  
Kambrook New Zealand, Private Bag 94411, Greenmount, Auckland, New Zealand  
Customer Service Line/Spare Parts 09 271 3980 Customer Service Fax 0800 288 513  
Due to continual improvement in design or otherwise, the product you purchase may differ slightly from the one illustrated in this book. Issue 1/05  
 

Indesit Oven FV 10 KB IX GB User Manual
Ingersoll Rand Water Pump 6662AX X C User Manual
JAMO DVD Player DMR 45 User Manual
JL Audio Car Speaker M 770x User Manual
Johnson Controls Air Conditioner GCGD18 thru 60 User Manual
Kambrook Water Heater KUR10 User Manual
Kenwood Marine Radio TS 820 User Manual
Kenwood Stereo System VRS 6200 User Manual
Kenwood Video Gaming Accessories PS 50 User Manual
King Canada Planer KC 425C User Manual