ꢀ
SHORT CORD INSTRUCTIONS
A short power supply cord is provided to reduce the hazards resulting
from becoming entangled in, or tripping over a longer cord.
Extension cords may be used if care is exercised in their use.
•
The electrical rating of the extension cord should be at least
that of the appliance. If the electrical rating of the extension
cord is too low, it could overheat and burn.
•
The resulting extended cord should be arranged so that it will
not hung over the counter top or tabletop where it can be
pulled on by children or tripped over.
SPECIFICATIONS
Electrical requirements
Fuse type
115V AC 60Hz, 1PH (Mono-phase)
AC 250V, 3.15A,∮5 x 20
Ice Making Capacity
Ice Sizes
Ice Storage Capacity
10-15 kg per day / 22-33 lb. per day
Small, Large
1.0 kg / 2.2 lb.
Compressor
High efficiency, CFC free
R134a
1.5 L / 50 Oz.
350 x 305 x 360 mm / 13 ¾ x 12 x 14 ¼ in.
13.0 kg / 28.6 lb.
Refrigerant gas
Water Reservoir
Dimensions
Net Weight
BEFORE USE
ꢁ
During transportation, DO not angle the cabinet over 45°
ꢁ
Do NOT put the ice cube maker upside down. Otherwise
Problems could occur in the compressor and sealed System.
The ice maker should be placed horizontally on a properly
leveled surface.
To ensure proper ventilation, it is important to set a minimum
space of 150mm / 6 in. at the top, at the back and on each side
for your ice cube maker.
ꢁ
ꢁ
ꢁ
ꢁ
Before using the Ice maker for the first time, please wait 2 hours
after putting it in place to start the appliance.
Clean the inner liner, ice collecting tray, water box, ice shovel
and evaporator frequently (see Cleaning and Care section).
3
USK ICBM 30116/30155 - 090716
ꢀ
Note: Do not use the Ice maker near an oven, radiator, or other heat
source.
PART DESCRIPTION
1.
2.
3.
4.
5.
6.
7
Lid
9
10.
11
12.
13.
14
15
Water drain plug
Compressor
Water pump
Power cord
Upper view
Control panel
Lid window
Ice collecting basket
Front housing
Water tank
Filter
Feet
Evaporator
Water inner tube
8.
CONTROL PANEL
A. START button
B. Size selector
C. STOP button
D. Ice full indicator
E. Cube size pilot lights
F. Water tank empty indicator
E
F
D
A
C
B
4
USK ICBM 30116/30155 - 090716
ꢀ
OPERATION
•
•
•
After having unpacked the appliance, clean water tank and ice
basket thoroughly. Wait for 2 hours before taking the next step.
Pour drinkable water in the water tank. Do not try to fill more than
50 Oz. water or above the level of the ice basket.
To select the size of the ice cubes, press the SELECT button until
the corresponding pilot light turns on. “S”: small, or “L”: large.
Press START button to start the ice making process.
If the water tank is getting empty, the “ADD WATER” pilot light will
turn on and a long beep will sound. In that case, the compressor
will stop automatically. Remove the ice basket, refill the water
tank. Wait for 3 mn after the beep sound before pressing the
START button to resume the ice making process.
•
•
•
When the “ICE FULL” pilot light switches on, a beep will sound; it
means that you should empty the ice basket. In that case, the
compressor will stop automatically. Empty the ice basket
completely or partially. Wait for 3 mn after the beep sound before
pressing the START button to resume the ice making process.
You can stop the ice making process at any time by pressing the
STOP button, to switch off the appliance.
Do not leave the ice maker non working for a long period of time,
as the water could get stale and improper for consumption. If you
do, please refer to the “Cleaning and Care” section of this user
manual.
•
•
NOTES:
ꢂ If the ambient temperature is below 15°C/60°F, we advise you
to select the small size. If the ambient temperature is higher
than 29°C/85°F, we recommend you select the large size.
ꢂ For best performance, the temperature of the water you pour
into the water tank should be between 7°C/45°F and
25°C/75°F and the ambient temperature between 15°C/60°F
and 37°F/100°F.
ꢂ If you select the large size, the ice making process will be a
little bit longer.
ꢂ You must press “START” button to restart the ice maker after
you add water or take out some of the ice after a warning
signal. If you do not, the compressor will automatically restart
5
USK ICBM 30116/30155 - 090716
ꢀ
operation though, when the temperature in cavity will reach
above 5°C/ 40°F
CLEANING AND CARE
•
If the compressor stops for any reason such as water shortage,
too much Ice, power off, etc... Do not start the system right
away, wait 3 minutes, and then re-start the Ice maker.
Always add fresh water before starting ice production at initial
installation or after long shut off periods.
•
•
To ensure the cleanliness of the ice cubes, water in the water
reservoir should be replaced every 24 hours
•
•
Always unplug the appliance before cleaning it.
Clean the inner liner, ice collecting tray, water box, ice shovel
and evaporator frequently. Please do not use chemicals
improper for parts in contact with food. Rinse thoroughly before
starting the appliance again
Wipe the appliance’s housing with kitchen paper or a soft damp
.
•
cloth.
•
•
•
•
NEVER immerse the appliance in water or any other liquid.
NEVER put any part of the appliance in the dishwasher.
Do NOT use abrasive products.
If you see a decrease in performance, limescale could be the
cause. Please use a solution with water and descaling agent
formulated for coffee makers (do NOT use vinegar). Start the ice
cube maker and let the solution run through for 5 minutes. Stop
the appliance for 5 minutes. Start the appliance again for 5
minutes and stop the appliance again. Remove all the solution
by using the drain plug at the back. Once done, rinse thoroughly,
repeating the whole operation twice or three times, this time with
clean water only. Do NOT consume the ice that might have been
done with the descaling solution.
•
When you know that you will not use the appliance for a long
period, remove the drain plug and let the water come out of the
water tank. Screw the drain plug back in place after the water
has been drained.
6
USK ICBM 30116/30155 - 090716
ꢀ
TROUBLESHOOTING
Problem
Possible Cause
Suggested Solutions
“Add water“ indicator
light is on, a long beep
sounds
There is no water
Fill the water tank with water,
wait 3 minutes and press the
start button to restart.
“Ice Full“ indicator
light is on, a beep
sounds
The ice tank full
capacity is reached
Empty ice basket completely
or partially, wait 3 minutes and
press the start button to restart.
My Ice melts
The compressor has
Restart the compressor by
stopped automatically. pressing on start after the “Ice
Full” or “Add Water” have
been lit (see above).
Nevertheless, operation will
restart automatically once the
temperature in the cavity will
be above 40°F
Pilot lights do not turn
on
Blown fuse/ No power
Check the power socket /
Have the fuse replaced by a
competent electrician. Please
use fuse value AC 250V, 3.15A,
∮5 x 20 only
The Ice made falls like
a single block, with a
lot of cubes sticking
together.
The water temperature Stop the machine and reset
in the water storage
box or ambient is too
low
the ice making cycle. Restart
the machine after turning it off.
Conditions for ice
Refrigerant might be
Call 1-888-KALORIK for service
making cycles are right leaking / sealed system or email through
but no ice is made.
is
blocked
The lights of ice full and Water tray is blocked
Unplug the appliance.
Clean the evaporator.
deficient come on in
the same time.
by ice cube
Plug the appliance back in
and press the ”START” button.
The appliance will restart
automatically after 2 minutes.
Please pull out the cap of the
water pipe, then let the water
through the pipe in order to
clean it and wash the clog
away, then replace the cap.
Resume operation.
The ice cube maker is
jammed, or the water
Water pipe is clogged
by limescale or other
does not flow uniformly particles
in the evaporator
7
USK ICBM 30116/30155 - 090716
ꢀ
WARRANTY
We suggest that you complete and return the enclosed Product
Registration Card promptly to facilitate verification of the date of
original purchase. However, return of the Product Registration Card is
not a condition of these warranties. You can also fill this warranty
card online, at the following address: www.KALORIK.com
This KALORIK product is warranted for 1 year from the date of
purchase against defects in material and workmanship. This warranty
is not transferable. Keep the original sales receipt. Proof of purchase
is required to obtain warranty performance.
During this period, the KALORIK product that, upon inspection by
KALORIK, is proved defective, will be repaired or replaced, at
KALORIK's option, without charge to the customer. If a replacement
product is sent, it will carry the remaining warranty of the original
product.
This warranty does not apply to any defect arising from a buyer's or
user's misuse of the product, negligence, failure to follow KALORIK
instructions noted in the user’s manual, use on current or voltage
other than that stamped on the product, wear and tear, alteration
or repair not authorized by KALORIK, or use for commercial purposes.
There is no warranty for glass parts, glass containers, filter basket,
blades and agitators, and accessories in general. There is also no
warranty for parts lost by the user.
ANY WARRANTY OF MERCHANTABILITY OR FITNESS WITH RESPECT TO
THIS PRODUCT IS ALSO LIMITED TO THE ONE YEAR LIMITED WARRANTY
PERIOD
Some states do not allow limitation on how long an implied warranty
lasts or do not allow the exclusion of incidental or consequential
damages, so the above limitations may not apply to you. This
warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
8
USK ICBM 30116/30155 - 090716
ꢀ
If the appliance should become defective within the warranty
period and more than 30 days after date of purchase, do not return
the appliance to the store: often, our Consumer Service
Representatives can help solve the problem without having the
product serviced. If servicing is needed, a Representative can
confirm whether the product is under warranty and direct you to the
nearest service location.
If this is the case, bring the product (or send it, postage prepaid),
along with proof of purchase and indicating a return authorization
number given by our Consumer Service Representatives, to the
nearest authorized KALORIK Service Centre (please visit our website
the address of the nearest authorized KALORIK Service Centre).
If you send the product, please include a letter explaining the nature
of the claimed defect.
If you have additional questions, please call our Consumer Service
Department (please see below for complete contact information),
Monday through Friday from 9:00am - 6:00pm (EST). Please note
hours are subject to change.
If you would like to write, please send your letter to:
KALORIK Consumer Service department
Team International Group of America Inc
1400 N.W 159th Street, Suite 102
Miami Gardens, FL 33169 USA
Or call :
Toll Free: +1 888-KALORIK
Only letters can be accepted at this address above. Shipments and
packages that do not have a return authorization number will be
refused.
9
USK ICBM 30116/30155 - 090716
ꢀ
10
USK ICBM 30116/30155 - 090716
ꢀ
11
USK ICBM 30116/30155 - 090716
|