DUAL ALARM CLOCK
with AM/FM RADIO
Instruction Manual
JL-355
Please read this manual carefully before operating
and save it for future reference.
GETTING STARTED
Location of Controls (Top / Back View)
1
2
3
4
5
6
7 8
9 10
11
12
1. STANDBY button
5. TUNING + button
6. SLEEP button
9. Dimmer Hi/Lo switch
10. ALARM 2 button
11. TUNING - button
12. AUX IN jack
2. Source(AM/FM/AUX) switch
3. SNOOZE button
7. VOLUME dial
4. ALARM 1 button
8. TIME SET / MEMORY button
Power Source
•
AC Power: Plug the AC power cord into the standard household outlet.
Caution: Before connecting the unit to power, please make sure your local
voltage is the same as marked on the back plate of the unit.
•
Backup battery: Install 1.5Vx2 AAA(UM4) size battery (not included)
into the battery compartment, and close the lid securely. These batteries
are to keep the clock running when the AC power is disconnected.
Caution: Make sure the positive (+) and negative (-) battery terminals are
attached to the corresponding plates in the battery compartment.
Printed in China
OPERATIONAL INSTRUCTIONS
Setting the Clock
1.
2.
3.
4.
Press and hold TIME SET / MEM and the hour will flash.
Press TUNING + / - to find the correct hour setting.
Press TIME SET / MEM again the minute will flash.
Press TUNING + / - to find the correct minute setting.
Using the Radio
1.
2.
3.
4.
5.
Press STANDBY to turn radio on.
Press SOURCE to select FM or AM mode.
Select your desired station using TUNING+ / -.
Turn the VOLUME CONTROL knob to adjust volume as needed.
Press STANDBY to turn radio off.
Wake to Radio
1.
Repeatedly press ALARM 1 / 2 until “RADIO” icon appears on the
LCD screen to indicate alarm status
2.
3.
4.
5.
Press and hold ALARM 1 / 2 and hour will flash.
Select your desired wake up hour using TUNING+ / -.
Press ALARM 1 / 2 and minute will flash.
Select your desired wake up minute using TUNING+ / -.
Wake to Buzzer
1. Repeatedly press ALARM 1 / 2 until “BUZZER” appears on the LCD
screen to indicate alarm status
2. Press and hold ALARM 1 / 2 and hour will flash.
3. Select your desired wake up hour using TUNING+ / -.
4. Press ALARM 1 / 2 and minute will flash.
5. Select your desired wake up minute using TUNING+ / -.
Alarm Duration and Snooze Function
Alarm Duration – Buzzer alarm or Radio alarm will continue output for
60 minutes if no buttons are pressed, then it will stop automatically and
sound again at same alarm time the next day.
Snooze Function:
1. When the Alarm sounds, press SNOOZE to enable the snooze
function, Buzzer alarm or Radio alarm will stop.
2. The alarm will sound again in 9 minutes
3. Unless STANDBY or ALARM 1 / 2 is pressed to stop the alarm,
the Snooze function will continue for up to 60 minutes from the
first alarm.
Printed in China
OPERATIONAL INSTRUCTIONS
Sleep Function
1. Press SLEEP to turn on sleep mode. Repeatedly press SLEEP to
adjust the duration between 90 min and 10 min.
2. Press STANDBY to cancel the sleep function.
AUX-In Jack
1. Connect the earphone socket from the Auxiliary unit (e.g. MP3
player or MD player) into AUX-In Jack on the rear of this product.
When inserting an Audio line cord, the main unit function will not
work and automatically enter the Auxiliary (AUX) function.
2. Press the PLAY button of the Auxiliary unit. Music from the Auxiliary
unit can be listened through the speaker of this product.
3. When using the AUX-In jack, Press SOURCE to select AM, FM or
AUX-In.
Programming Radio Stations in Memory
1. The program memory allows you store 40 stations (20 AM / 20 FM),
2. In AM or FM mode, select your desired station.
3. Press and hold TIME SET/ MEMORY. “P-01” will blink on LCD
screen.
4. Press TIME SET/MEMORY again to store the station. You can
select the desired program preset number (1-20) by pressing
TUNING+/-.
5. Using preset station, press TIME SET/MEMORY, “P-01” will appear
on LCD screen. Press TUNING+/- to select your desired preset
number.
6. If you wish to replace a memory position with a station other than
the current one, the new station can be programmed as described
above. This will automatically replace the original station.
Printed in China
TROUBLESHOOTING GUIDE
When the instructions in this manual are followed, this unit should function
properly. However, if any of the following difficulties occur and cannot be
corrected by the user or if a problem arises that is not mentioned here,
please contact jWIN Customer Service or a qualified service technician.
1. Unit Does Not Play
•
Unit may be disconnected from power source. Check connection.
2. No Sound, Distorted Sound or Feedback
•
•
Volume control is turned down. Please increase.
The unit may be located where there is vibration. Move unit if
necessary.
3. Radio Reception is Unclear or distorted
•
Radio station frequency may be weak. Adjust antenna or move near
a window.
4. Time is incorrect.
•
•
Backup batteries may be dead. Change batteries.
Clock may not be set correctly. Set the clock.
5. Alarm does not function
•
The unit may not be set properly. Select ALARM 1 / 2 and switch to
Radio or Buzz.
•
•
Make sure the clock is set properly.
Make sure the alarm time is set correctly.
Cleaning the cabinet
Do not use polish solvents or strong detergents to clean the unit. The
cabinet can be cleaned with a piece of soft cloth soaked with little water.
The power plug should ALWAYS be disconnected from the main power
supply during the cleaning.
Printed in China
USER SAFETY GIUDE
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To prevent fire or shock hazard, do not expose this appliance
to rain or moisture.
These markings are located on the bottom, side or back of the unit.
CAUTION: To prevent the risk of electric shock, do not remove cover (or
back). Non- user-serviceable parts inside. Refer servicing to a service
professional.
•
The lightning flash with an arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of un-insulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to a person.
•
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating, maintenance and
servicing instructions in the literature accompanying the appliance.
Dripping warning: "This product shall not be exposed to any dripping or
splashing, and no objects filled with liquids, such as vases, shall be placed
on or near the product."
Ventilation warning: "The normal ventilation of the product shall not be
impeded for intended use." (Minimum distances must be kept around the
apparatus for sufficient ventilation, especially while use of the apparatus is
in tropical and/or moderate climates.)
Printed in China
USER SAFETY GIUDE
INSTRUCTIONS ON ENVIRONMENT PROTECTION
Do not dispose of this product in the usual household
garbage at the end of its life cycle; bring it to a collection
point for the recycling of electrical and electronic appliances.
This symbol on the product means the instructions for use or
the packing will inform about the methods for disposal. The
materials are recyclable as mentioned in its marking. By
recycling, material recycling, or other forms of re-utilization of old
appliances, you make an important contribution to protect the environment.
Please inquire at your local community administration for the authorized
disposal location.
IMPORTANT SAFETY PRECAUTIONS
1. READ INSTRUCTIONS - All safety and operating instructions should be
read before the appliance is operated.
2. RETAIN INSTRUCTIONS - The safety and operating instructions should
be retained in a secure place for future reference.
3. HEED WARNINGS - All warnings on the appliance and in the operating
instructions should be observed.
4. FOLLOW INSTRUCTIONS - All operating and use instructions should be
followed.
5. WATER AND MOISTURE - The appliance should not be used near water.
For example: near a bathtub, kitchen sink, laundry tub, and swimming
pool or even in a wet basement.
6. VENTILATION - The appliance should be situated so that its location and
position does not interfere with its proper ventilation. For example, the
appliance should not be situated on a bed, sofa, rug or similar surface that
may block the ventilation openings; or, be placed in a built-in installation,
such as a bookcase or cabinet that may impede the flow of air through the
ventilation openings.
7. HEAT - The appliance should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including amplifiers)
that produce heat.
Printed in China
USER SAFETY GIUDE
IMPORTANT SAFETY PRECAUTIONS – CONTINUED
8. POWER SOURCES - The appliance should be connected to a power
supply only of the type described in the operating instructions or as
marked on the appliance.
9. GROUNDING AND POLARIZATION - Precautions should be taken to
ensure that the grounding or polarization of the appliance is correct.
10. POWER CORD PROTECTION - Power supply cords should be routed so
that they are not likely to be walked on or obstructed by items placed
upon or against them. Pay particular attention to cords at plugs,
convenience receptacles, and the point at which they exit from the
appliance.
11. CLEANING - The appliance should be cleaned only as recommended by
the manufacturer.
12. POWER LINES - An outdoor antenna should be located away from power
lines.
13. NONUSE PERIODS - The power cord of the appliance should be
unplugged from the outlet when the appliance is to be left unused for an
extended period of time.
14. OBJECT and LIQUID ENTRY - Care should be taken so that objects do
not fall and liquids are not spilled into the device’s openings.
15. CARTS AND STANDS - The appliance should be used
only with a cart or stand that is recommended by the
manufacturer. An appliance and cart combination
should be moved with care. Quick stops, excessive
force, and uneven surfaces may cause the appliance
and cart combination to overturn.
16. WALL OR CEILING MOUNTING - If the appliance is mounted to a wall
or ceiling, it should be mounted only as recommended by the
manufacturer.
Printed in China
USER SAFETY GIUDE
IMPORTANT SAFETY PRECAUTIONS – CONTINUED
17. DAMAGE REQUIRING SERVICE - The appliance should be serviced
by qualified service professional when:
a. The power-supply cord or plug has been damaged.
b. Objects have fallen into, or liquid has been spilled into the
appliance’s apertures.
c. The appliance has been exposed to rain.
d. The appliance has been dropped and suffered damage.
e. The appliance does not appear to operate normally or exhibits a
marked change in performance.
18. SERVICING - The user should not attempt to service the appliance
beyond that described in the user's operating instructions. All other
servicing should be referred to qualified service professional.
19. PROTECTIVE ATTACHMENT PLUG - The appliance is equipped with
an attachment plug that has an overload protection. This is a safety
feature. If replacement of the plug is required, be sure the service
technician has used a replacement plug specified by the manufacturer
that has the same overload protection as the original plug. (UK Version
Only)
FCC NOTICE (USA)
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC regulations state that any change or modification to the
equipment, not expressly approved by maker or its authorized parties,
could void user’s authority to operate this equipment.
•
•
To prevent fire or electric shock, do not expose the unit to rain or
moisture.
Never attempt to open the cabinet. Dangerous high voltages are present
in the unit. Always refer servicing to a qualified technician.
IC NOTICE (CANADA)
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio Interference
Regulations of Industry Canada.
Printed in China
SPECIFICATIONS
•
•
Frequency Range
o AM: 530kHz – 1710kHz
o FM: 87.5MHz – 108MHz
Power Requirement
o AC 120V, 60Hz
o Battery: 1.5Vx2 AAA battery for clock backup (battery not
included)
•
•
Power Consumption: ≤ 5W
Unit Dimensions (W x H x D): 7.5” x 3.5” x 2.2” (200mm x 88mm x
55mm)
•
Unit Weight: Approx. 0.53kg
* Specifications and features are subject to change without prior notice.
Printed in China
TEL: 1-866-807-5946
© 2010 jWIN Electronics Corp. All rights reserved. No portion of this printed
material or product enclosed herewith including design, shape and graphics, may
be reproduced or transmitted in any form without prior written consent of jWIN
Electronics Corp. by any means, electronic or mechanical, including
photocopying, recording or use of an information storage and retrieval system.
Any unauthorized distribution or reproduction of this printed material or product, or
any portion thereof, will be prosecuted to the fullest possible extent of the law.
Printed in China
|