JLDV 02
vented tumble dryer
Instruction manual
Dry time
Cooling 10 minutes
Refresh
Off
Extra dry
Store dry
Drying
Cooling
End
Delicates 2kg
Heavy cotton
Extra delicate
30 minutes
Cupboard dry
Damp dry
Filter
Alarm
off
Half
Quick power
Delay
start
Start/
Pause
Iron dry
Door
Extra damp
Extra dry
Cupboard dry
Iron dry
JLDV02
1
Ecological hints
The symbol
on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical
and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential
negative consequences for the environment and human
health, which could otherwise be caused by in appropriate
waste handling of this product. For more detailed
information about recycling of this product, please
contact your local city office, your household waste
disposal service or the shop where you purchased the
product.
To save energy we recommend that you follow these
hints:
• Try to load the maximum capacity of the machine as
small loads are uneconomical.
• Always load well spun laundry. The higher the spin
speed, the lower the electricity consumption and the
shorter the drying times.
• Do not over-dry laundry, this avoids creasing and saves
energy.
• Clean the filters regularly to avoid excessive drying
times and high electricity consumption.
• The room should be well ventilated for the tumble
Dryer to operate efficiently. The room temperature
should not exceed +35°C during drying.
Environmental Information
• After unpacking please dispose of the packaging with
due regard to safety and the environment
• Materials marked with the symbol
are recyclable.
• Check with your local Council or Environmental Health
Office to see if there are facilities in your area for re-
cycling this appliance.
• When the appliance is to be scrapped, cut off the
power supply cable and make the door closing device
unusable to prevent young children from being trapped
inside.
• Check with your local Council or Environmental Health
Office to see if there are facilities in your area for re-
cycling this appliance.
Warning !
A cut off plug inserted into a 13amp socket is a
serious safety (shock) hazard. Ensure that the cut
off plug is disposed of safely.
3
Contents
For the User
For the Installer
Important Safety Information
• Installation
2
Installation
6
Technical Specifications
6
6
• Unpacking
7
Description of the Appliance
The Control Panel
5
• Positioning
7
7-8
8
•Fitting the vent hose
• Stacking kit (optional accessory)
• Door reversal
10
8
• Door Release Button
• No Buzzer Button
• Quick Dry Button
• Low Temperature Button
• Delay Start Button
• Display
10
10
10
10
10
11
11
12
13
Electrical connection
9
• Start/Pause Button
• Indicator Lights
• Programme/Time Selector Dial
Programme Chart
13
14
15
16
16
16
16
16
Guide to using the Instruction Manual
The following symbols will be found in the text to
Using your tumble dryer
Hints & Tips on Drying
Maintenance and Cleaning
• External cleaning
• Cleaning the door
• Cleaning the filters
• Cleaning the drum
guide you throughout the instructions:
Safety instructions
Hints and tips
Environmental information
Adjusting the level of conductivity 17
Something Not Working
Repairs - After Sales Service
Spare parts
18
19
19
This appliance complies with the following E.E.C.
Directives:
- 73/23 EEC of 19.2.73 (Low Voltage Directive)
and subsequent modifications;
- 89/336 EEC of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent
modifications.
4
Description of the Appliance
1
01 Control panel
2 Drum Light
2
3
03 Fluff filters
04 Rating Plate
05 Adjustable feet
4
5
6
7
8
Side vent outlet
Ring nut
Rear vent outlet
6
8
7
5
Installation
It is dangerous to alter the specifications or
attempt to modify this product in any way.
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
Technical Specifications
DIMENSIONS
Height
Width
Depth
85 cm (33.5”)
60 cm (23.6”)
58 cm (22.8”)
POWER SUPPLY VOLTAGE
TOTAL POWER ADSORBED
230-240 V/50 Hz
2650 W (13A)
MAX LOAD CAPACITY
Cotton, linen
Synthetics
6 kg (13.2 lbs)
3 kg (06.6 lbs)
DRUM VOLUME
108 l
CONSUMPTIONS
Cotton, linen
Cotton, linen
Synthetics
3.30 kWh (6, kg cupboard dry)
2.60 kWh (6 kg iron dry)
1.10 kWh (3 kg cupboard dry)
6
Important
Unpacking
The hot air emitted by the tumble dryer can reach
temperatures of up to 60°C. The appliance must be sited
in a well ventilated room but not be installed on floors
which are not resistant to high temperatures.
Warning !
Slide out the polythene bag containing the
polystyrene block before using the appliance. Pull
off adhesive strips from inside machine on top of
drum.
When operating the tumble dryer, the room temperature
must not be lower than +5°C and no higher than +35°C, as
it may affect the performance of the appliance.
Keep all packaging away from children
Fitting the vent hose
Depending on the position of the tumble dryer to an
outside wall there is a choice of 3 vent outlets: One at
the back, the others on the left or right hand side.
Connect the hose to whichever is the more convenient
by pulling the ring nut (A) from the vent outlet at the
back, screwing it on to the hose and pushing it firmly back
into place.
The unused vents should now be sealed with the special
snap covers provided.
P1106
Should the appliance be moved, it must
be transported vertically.
A
Positioning
It is recommended that, for your convenience, the
machine is positioned close to your washing machine.
The tumble dryer must be installed in a clean place,
where dirt does not build up.
Air must be able to circulate freely all around the
appliance. It is important to ensure the air intake grills on
the back of the dryer are not obstructed with any
materials (e.g. paper, rags etc.). Obstructing the grills
could be dangerous or at least seriously impair the
efficiency of the tumble dryer.
A
P1028
P1027
Advice: If the hose is long and the room temperature
low, the moisture might condense to water inside the
hose. This is nothing to be concerned about.
To prevent this water from lying in the hose or flowing
back into the tumble dryer, it is advisable to drill a small
hole (dia. 3 mm) in the lowest point of the hose and to
place a small container below it.(See picture, point B).
To keep vibration and noise to a minimum when the
dryer is in use, it should be placed on a firm, level surface.
Once in its permanent operating position, check that the
dryer is absolutely level with the aid of a spirit level. If it is
not, raise or lower the feet until it is.
B
P1056
.
P0046
The feet must never be removed.
Do not restrict the floor clearance through deep-
pile carpets, strips of wood or similar. This might
cause heat build-up which would interfere with
the operation of the appliance.
7
Once connected to the dryer, run the vent hose to the
desired outlet point, ensuring that the run’s overall length
is less than 2 m, and that it contains no more than two
bends. As to the outlet itself, if you have decided on a
fixed wall/window grille, a good local builder’s merchant
should be able to supply you with the necessary fittings
and installation advice.
Stacking kit (optional accessory)
It should be possible to stack your new dryer on top of a
front loading washing machine with a cover’s depth
between 48 and 60 cm.
Read carefully the instructions supplied with the stacking
kit.
Please contact your local John Lewis branch for further
advice.
It is important not to connect the
vent hose to items designed to carry
exhaust from a fuel burning appliance,
eg. cooked hoods, chimney or flue
pipes.
P1107
Door reversal
To make it easier to load or unload the laundry the door
can be reversed.
P0055
This operation must be carried out by qualified
personnel.
Please contact the telephone number given under Repairs
- After Sales Service, page 19.
Hints and Tips
Note that to avoid condensation problems, it is essential
that the dryer be fitted with the flexible hose to carry its
“exhaust” at least beyond the kitchen units; preferably
outside the kitchen.
In order to prevent the appliance from overheating, it is
important that the steam exhaust is unobstructed.
Therefore, in case of a permanent hose fitted to an
exterior wall or ceiling, it must be ensured an exhaust
3
capacity of at least 150 m /h.
If the dryer is fitted next to kitchen units, make
sure that the vent hose is not squashed. If the hose
is partially squashed, drying efficiency will be
reduced, resulting in longer drying times and
higher energy consumption.
If the hose is completely squashed, the safety cut-
outs with which the machine is fitted may operate.
8
Electrical connection
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
4. Upon completion there must be no cut, or stray
strands of wire present and the cord clamp must be
secure over the outer sheath.
WARNING:
WARNING: THIS APPLIANCE MUST
BE EARTHED.
A cut off plug inserted into a 13 amp
socket is a serious safety (shock)
hazard.
Ensure that the cut off plug is disposed of
safely.
Should the appliance power supply cable
need to be replaced, this must be carried
out by a Service Force agent (see page 19).
The manufacturer declines any liability
should this safety measure not be
observed.
The plug must still be accessible after the
appliance has been installed.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliance’s
rating plate. (See picture on page 5).
The appliance should not be connected
to the electrical supply by means of an
extension cable
The appliance is supplied with a 13amp plug fitted.
In the event of having to change the fuse in the plug
supplied, a 13amp ASTA approved BS 1363/A fuse must
be used.
Should the plug need to be replaced for any reason, proceed
as described below. The wires in the mains lead are
coloured in accordance with the following code:
Permanent connection
In the case of permanent connection it is necessary that
you install a double pole switch between the appliance
and the electricity supply (mains), with a minimum gap of
3mm between the switch contacts and of a type suitable
for the required load in compliance with the current
electrical regulations.
Green and Yellow
Blue
- Earth
- Neutral
- Live
The switch must not break the yellow and green earth
cable at any point.
Brown
GREEN & YELLOW
E
L
N
BROWN
BLUE
CORD CLAMP
P1041
If you fit your own plug, the colours of the wires in the
mains lead of your appliance may not correspond with the
markings identifying the terminals in your plug.
Proceed as follows:
1. Connect the Green and Yellow (earth) wire to the
terminal in the plug which is marked with the letter "E" or
the earth symbol
or coloured green and yellow.
2. Connect the Blue (neutral) wire to the terminal in the plug
which is marked with the letter "N" or coloured black.
3. Connect the Brown (live) wire to the terminal in the
plug which is marked with the letter "L" or coloured red.
9
The control panel
Dry time
Off
Extra dry
Store dry
Cooling 10 minutes
Refresh
Drying
Cooling
End
Delicates 2kg
Heavy cotton
Extra delicate
30 minutes
Cupboard dry
Damp dry
Filter
Alarm
off
Half
Quick power
Delay
start
Start/
Pause
Iron dry
Door
Extra damp
Extra dry
Cupboard dry
Iron dry
JLDV02
4 Half Power Button
Pressing this button allows drying to be performed at a
lower temperature, for delicate items.
1
Door release Button
Press this button to open the door. The light above the
button will illuminate.
The corresponding pilot light comes on.
This option can also be used for time controlled drying.
This option cannot be selected with QUICK and
DELICATES programme.
Opening the door by means of this button is
possible only if the tumble dryer is on
(programme selector dial set to a programme or
drying time).
If you open the door during a programme, in order to
restart the programme you must press the
START/PAUSE button again after having closed the door.
5 Delay Start button
This button allows you to delay the starting of the
programme by up to 12 hours.
This option must be selected after having selected the
programme and before pressing START/PAUSE to start
the programme.
2 Alarm off Button
A buzzer sounds
• when selecting the programme
• when depressing the buttons
• when an incorrect option selection is made
Every time the button is pressed, the time is increased by
30 minutes, until the display shows a delay of “2 hours”.
After this, the delay is displayed hour by hour.
• when the programme selector dial is turned to another
position during the programme or when you depress an
option button during the cycle
The minutes or hours of delay that have been selected
are displayed for 2 seconds, then the display shows the
duration of the previously selected programme.
• at the end of the programme
The countdown begins after you have pressed the
START/PAUSE button.
• if the machine is not working correctly
• when the small door at the bottom is open.
By depressing the button the acoustic signal is switched off.
The corresponding light comes on.
To cancel the delay time, during the drying phase the
START/PAUSE button to set your appliance to pause and
then press the DELAY START button until the display
indicates 0’. Then press the START/PAUSE button again.
When the delay is cancelled, the display shows the
duration of the programme.
3 Quick dry Button
During the delayed start, it is not possible to change the
programme or the delay time that has been selected. To
do this, you must first switch off the machine by setting
the programme selector dial to “Off”. Select the new
programme, the options and the delayed start, then press
the START/PAUSE button.
By depressing this button the drying time is reduced in
the following COTTON programmes:
• EXTRA DRY
• CUPBOARD DRY
• STORE DRY
If you wish to add more laundry while the machine is
performing the countdown, simply open the door. When
you close the door, press the START/PAUSE button again
to cause the countdown to be resumed.
The corresponding pilot light comes on.
This option cannot be selected with HALF POWER
function.
10
• Incorrect option selection
If you select an option that is not compatible with the
programme you have selected, the display shows Err
(error).
6 Display
The display shows the following information:
• duration of selected programme
• delayed start
• end of programme
• incorrect option selection
• alarm code
• Duration of selected programme
After you have selected the programme, its duration (in
hours and minutes) appears on the display. It is calculated
automatically on the basis of the maximum load accepted
for each type of fabric and of the required degree of drying.
This code will reappear during the execution of the
programme if you press one of the option buttons.
• Alarm code
In the case of a functional problem, the display shows
an alarm code (e.g. E21). See page 13 for more detailed
information.
1.20
When the programme starts, the remaining time is
displayed every 5 minutes.
• Delayed start
E21
If you have selected a delay time by means of the
relevant button, the display shows it for 2 seconds; then
it shows the duration of the previously selected programme.
The countdown is displayed every 30 minutes until it
displays “90 minutes” and then hour by hour.
7 Start/Pause button
Press this button to start the dryer after having selected
the programme and the options.
The relevant light will stop flashing. If you have chosen a
delayed start, the machine will begin the countdown.
If the door of the appliance or the small door at
the bottom is opened while the programme is
running, this button must be pressed again after
closing the door in order to restart the
programme from the point at which it was
interrupted.
3
• End of programme
A flashing zero indicates the end of the programme
and it is displayed after the “anti-creasing” phase.
In both cases the light of the Start/Pause button flashes to
remind you that the start button needs to be pressed
again.
0
11
8 Indicator Lights
These lights indicate the following functions:
9 Programme/Time Selector Dial
Allows you to select electronically controlled or time
controlled drying.
“Drying” light
Turn the dial to the required programme or time.
This light indicates that the appliance is in the drying
phase.
Electronically controlled drying (automatic)
The appliance runs these programmes with the help of
sensors which detect the degree of dampness of the
laundry.
Simply select the programme according to the type of
laundry and degree of drying required.
“Cooling” light
This light indicates that the appliance is in the cooling
phase. At the end of drying, there is a 10 minute cooling
phase to cool the laundry.
“End” light
Time controlled drying
This light illuminates at the end of the cooling phase,
during the anti-creasing phase and at the end of the
programme.
This can be used to finish off drying if necessary.
Select the 30 minute programme for synthetics.
To cancel a programme which is running, turn the
programme selector dial to “Off”.
“Filter” light
At the end of drying, turn the selector dial to “Off” to
switch the machine off before removing the laundry.
This light illuminates at the end of the programme to
remind you that the filters must be cleaned.
If the programme selector dial is turned to another
position, when the machine is running, the buzzer will
sound and the programme phase indicator lights will flash.
12
Programme Chart
Automatic drying (electronic programmes)
Degree of drying
Type of laundry
Max-load (1)
required
Extra dry
Store dry
6 kg
6 kg
6 kg
6 kg
6 kg
6 kg
Cupboard dry
Cotton
Damp dry
Iron dry
Extra damp
Extra dry
3 kg
3 kg
3 kg
Synthetics
Cupboard dry
Iron dry
Synthetics or mixed fabrics
which do not require ironing
Extra delicate
2.5 kg
6 kg
Heavy cotton
Jeans
Jumpers
Delicates
Refresh
2 kg
2.5 kg
Synthetics
•
Extra delicate cycle is a special programme for synthetics or mixed fabrics which do not require ironing,
and need to be "STORE DRY".
•
•
Delicates is a special programme for jumpers to be dried “store dry”.
Refresh cycle is a special programme for synthetics.
Time controlled drying
Programme
selector dial position
Max-load (1)
Type of laundry
Drying time
Synthetics
3 kg
30’ minutes
30 min
(1) Never overfill the drum (do not load large quilts, for example).
Drying times vary according to:
• The type of laundry
• The size of the load
• The degree of water extraction obtained during the spin cycle of the washing machine.
• The degree of dryness required
Cooling 10 minutes
This position on the programme selector dial can be used to freshen the laundry (e.g. to remove a persistent odour of
moth-balls).
Load
It is often difficult to estimate the weight of items to be dried. We therefore recommend that you adopt the following
guidelines:
• cotton, linen: drum full but not too tightly packed;
• synthetics: drum no more than half full;
• delicate fabrics: drum no more than one third full.
13
Using the tumble dryer
The END and FILTER ights remain lit and the buzzer
sounds every 10 seconds for 2 minutes.
Before using your tumble dryer for the first time, we
recommend that you to place a few damp cloths
inside the appliance and dry for 30 minutes.
The light of the START/PAUSE button goes off and a
flashing zero appears on the display.
There may be dust inside a brand new tumble dryer.
10. Turn the programme selector dial to “Off”; all the
lights go out. The appliance is switched off.
Drying
Remove the laundry.
1. Connect the appliance.
If you open and then close the door before
turning the programme selector dial to
“Off”, all the lights corresponding to the
phases making up the performed
2. Open the door (see picture).
programme come on and the display shows
the duration of the programme.
After each use
• Clean the filters (see page 16).
P1104
P1108
3. Load the items one at a time, shaking them out
loosely.
Important!
4. Close the door. Please check the laundry does not get
caught between the door and filter.
If the drying programme has to be stopped before it
reaches the end, we recommend that you turn the
programme selector dial to position “Cooling” and wait
until the end of this phase before removing the laundry.
This will avoid a build-up of heat inside the appliance. To
do this first turn the dial to “Off” and then to “Cooling”
5. Select the drying programme or time. The lights
DRYING, COOLING and END come on. The light of
the START/PAUSE button flashes and the display
shows the duration of the programme.
and depress START/PAUSE Button
.
6. If required, press the HALF POWER button and/or
the ALARM OFF button or the QUICK button.
Modifying the programme
7. Select the DELAY START if required. The selected
delay appears on the display for 2 seconds, then the
duration of the selected programme is displayed.
To change a programme which is running, first cancel it by
turning the programme selector dial to “Off”. Select the
new programme and press the START/PAUSE Button.
8. Press the START/PAUSE button: the corresponding
light stops flashing and drying starts. Only the
DRYING light stays lit. If you have selected the
DELAY START, the machine begins its countdown.
If the programme selector dial is turned to another
position, when the machine is running, the buzzer will
sound, the programme phase indicator lights will flash.
The drum turns alternately in both directions during
drying.
All drying programmes end with a 10 minute cooling
phase (COOLING light illuminates).
You may remove the laundry after this phase.
The lights END and FILTER illuminate and the buzzer
sounds.
The display shows a static zero.
9. If the laundry is not removed at the end of the cycle,
the dryer performs an anti-creasing phase (duration:
30 minutes maximum).
If you do not remove the laundry, the dryer will stop
automatically at the end of the anti-creasing phase.
14
Hints & Tips on Drying
• Always load well spun laundry. The higher the spin
speed the lower the electricity consumption and the
shorter the drying time.
Before placing articles of laundry in your tumble
dryer, check the care labels to ensure they are
recommended for tumble drying.
• DO NOT load dripping wet laundry into the dryer. Roll
the article in a towel or spin to remove excess water.
Care Labels you may find on your laundry
• Close poppers and zips and fasten any buttons.
may be tumble dried
• Sort the laundry. Separate synthetics from
cotton/linens, and dry separately.
normal drying (high temperature)
delicate drying (low temperature)
do not tumble dry
• Remove the laundry immediately after the programme
has finished.
• Use a fabric conditioning sheet to reduce static. We
recommend the sheet is pinned to an article of laundry
(using a safety pin).
• Mix the load i.e. large and small articles.
• When drying large items such as sheets, we
recommend you periodically stop the dryer to
redistribute the load.
Do not overload the appliance.
DO NOT use the tumble dryer to dry the
following:
Here is a list of the approximate weight of some common
laundry items.
• Articles contaminated with inflammable substances e.g.
petrol, cleaning solvents, cooking oil, fats or hair
lacquer.
Sheet
700 to 1000 g
100 to 200 g
400 to 500 g
50 to 100 g
• Woollen and synthetic/wool mixtures unless the item is
labelled as suitable for tumble drying.
Pillowcase
Tablecloth
Table Napkin
Kitchen Towel
Linen Hand Towel
Hand Towel
Bath Towel
Bathrobe
• Very delicate articles such as silk.
• Very large and bulky items such as duvets or sleeping
bags.
70 to 120 g
100 to 150 g
150 to 250 g
700 to 1000 g
1000 to 1500 g
200 to 300 g
150 to 200 g
Shirt
Apron
15
Maintenance and Cleaning
After a while, a whitish coating due to detergent residue
You must disconnect the appliance from the
electricity supply, before you can carry out any
cleaning or maintenance work.
on laundry forms on the filters. When this occurs, clean
the filters with warm water using a brush. Remove the
filter in the door opening as per picture (it can be
positioned with the tooth facing to the left or to the
right).
External cleaning
Use only soap and water and then dry thoroughly.
Important: do not use methylated spirit, diluents or
similar products.
S
E
650
E
R
E
V
5
'
6
0'
5'
T
O
R
0
-
-
,
5
kg
k
g
2
1
A
U
/
12
00
95'
65'
3
1000
7
30
'
0
/
-
-
90
800
5'
-
-
/
120
0
'
1
00'
70
'
80
5'
5
0'
/
90
0
85
'
800
70'
3
5'
-
5
-
-
9
5
0'
0'
45'
-
kg
kg
5
2
5'
,5
Cleaning the door
Clean periodically the interior part of the door to
remove any fluff from the seals around the filter.
P1112
Regular cleaning ensures correct drying.
S
E
650
R
E
V
5
0
'
-
60'
T
O
R
,
5
U
kg
2
A
/
12
00
95'
65'
-
3
5'
1000
30
'
/
-
-
90
0
kg
1
800
-
-
7
5'
/
120
0
1000
80
5'
'
10
0'
70
'
0
'
5
0'
/
90
85
800
70'
35'
-
6
5'
5
90
0'
'
-
-
45'
-
kg
kg
5
2
3
0'
5
,5
Do not use the appliance without filters.
Cleaning the drum
If the laundry is not drying to the level of dryness you
have set, either too dry or too damp, we advise you to
clean the inside of the drum with a cloth soaked with
vinegar.
P1109
Cleaning the filters
Your dryer will only function well if the filters are clean.
The filters collect all the fluff which accumulates during
drying and they must therefore be cleaned at the end of
each programme, before removing the laundry, with a
damp cloth. The FILTER light reminds you to carry out
this operation.
This will eliminate the slight residue of detergent and
softeners used in the washing, or to any residue lime
contained in the water. A build up of these residues will
prevent the sensors from correctly measuring the degree
of dryness of the laundry.
S
E
650
E
R
E
V
5
0
'
-
-
6
0'
5'
T
O
R
,
5
U
12
00
95'
65'
kg
k
g
2
1
3
A
/
1000
7
30
'
/
-
-
90
0
800
5'
-
-
/
120
0
1000
6
80
5'
'
1
00'
70
'
0
5
0'
/
90
85
'
800
70'
35'
5'
-
5
-
-
9
5
0'
0'
-
'
45
kg
kg
5
2
3
0'
,5
P1111
P1110
The filter in the inner door must be removed for cleaning.
Do not be alarmed by the amount of fluff. It is not due to
excessive wear caused by the dryer. All fabric looses fluff
when line-drying but it goes un-noticed in the air. In a
tumble dryer it simply collects in the filter.
16
Adjusting the level of conductivity
Water contains, a variable quantity of limestone and
mineral salts of which quantities vary according to
geographical locations thus varying its conductivity values.
Conductivity
degree
Approximative
value (µS/cm)
Display
Relevant variations of the conductivity of the water
compared to those prefixed by the factory could slightly
influence the residual humidity of the laundry at the end
of the cycle.
Low
Medium
High
< 300
C0
C0
C0
300 - 600
> 600
Your dryer allows you to regulate the sensitivity of the
drying sensor based on conductivity values of the water
by using the following procedure.
Memorising the new setting:
Simultaneously press down the buttons 3 and 6 until the
previous drying cycle time appears again on the display
and the buzzer sounds.
To establish the hardness of your water to correspond
with the table opposite please contact your local water
authority.
Procedure:
Turn the programme selector dial to switch on the
appliance
In selection mode press simultaneously the buttons 3 and
6 until «C0» appears on the digits.
Dry time
Off
Extra dry
Store dry
Cooling 10 minutes
Refresh
Drying
Cooling
End
Delicates 2kg
Heavy cotton
Extra delicate
30 minutes
Cupboard dry
Damp dry
Filter
Iron dry
Alarm
off
Half
Quick power
Delay
start
Start/
Pause
Door
Extra damp
Extra dry
1 2 3 4 5
6
Cupboard dry
Iron dry
Adjusting the level of conductivity:
Press the button 5 sequentially: the level of conductivity is
indicated by the lighting of the horizontal hyphens.
17
Something Not Working
If the tumble dryer is not working correctly, please carry out the following checks before contacting your local Service
Force agent.
IMPORTANT: If the END light flashes, the buzzer sounds and an alarm code is displayed, switch the machine off and
call the telephone number given below.
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation a charge will be made even if the appliance is under guarantee.
Symptom
Solution
The tumble dryer does not start
• The door(s) has (have) not been closed.
• The plug is not properly inserted in the power socket.
• There is no current at the socket.
• The main fuse or the fuse in the plug has blown.
• The selector dial is not set correctly.
• The START/PAUSE Button has not been depressed.
• The DELAY START option has been selected.
Drying takes too long or laundry is not
dry enough.
• The laundry has not been spun properly.
• The filters and are clogged.
• The room temperature is too high.
• The selected time or drying cycle was not suitable for
the laundry.
• The LOW TEMPERATURE button has been pressed.
• There is too much laundry inside the appliance.
• The dryer is not correctly installed.
The drum light does not light up:
• The Programme/Time selector dial is on position “OFF”.
• The lamp is defective.
18
Repairs - After Sales Service
Spare parts
In the unlikely event of your appliance requiring service,
or if you wish to purchase spare parts, please contact our
extended warranty administrators by telephoning:
Always insist on genuine spare parts.
An authorised service engineer should service this
product, and only genuine spare parts should be used.
Under no circumstances should you attempt to repair
the machine yourself. Repairs carried out by
inexperienced persons may cause injury or serious
malfunctioning. Contact your local Service Force Centre.
An authorised service engineer always insist on genuine
spare parts.
0870 010 7887
They will give you details for your local Service Force
Centre.
Before calling out an engineer, please ensure you have
read the details under the heading “Something Not
Working”.
When you contact your local Service Force Centre you
will need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of fault
4. The purchase date and found on your receipt.
5. The model and serial number of the appliance (found
on the rating plate - see picture on page 5)
So that you always have these numbers at hand, we
recommend you to make a note of them here:
Mod. :. . . . . . . . . . . . . . . . .
PNC :. . . . . . . . . . . . . . . . . .
S.N. :. . . . . . . . . . . . . . . . . .
Your dryer is covered by a 3 year parts and labour
guarantee (see separate details given at point of
sale). Please retain your purchase receipt safely
for the service engineer to verify the purchase
details.
19
|