ENGLISH
EN
VIDEO CASSETTE RECORDER
HR-V400/207/200AG
HR-V401/201AS
HR-V200AA
INSTRUCTIONS
LPT0808-001B
Printed in China
0803-AH-PJ-BJ
COPYRIGHT © 2003 VICTOR COMPANY OF JAPAN, LTD.
CONTENTS
ATTENTION
1. This recorder can also receive SECAM colour television
signals for recording and playback.
Buttons, Connectors and Indicators................................................ 3
2. Recordings made of SECAM television signals produce
monochrome pictures if played back on another video
recorder of SECAM standard, or do not produce normal
colour pictures if played back on another video recorder of
PAL standard.
3. SECAM prerecorded cassettes or recordings made with a
SECAM video recorder produce monochrome pictures when
played back with this recorder.
Basic Connections......................................................................... 4
Initial Settings ............................................................................. 4
Video Channel Set ................................................................. 4
Auto Set Up ........................................................................... 5
Language Setting.................................................................... 5
Clock Setting.......................................................................... 5
Playback...................................................................................... 6
Basic Playback....................................................................... 6
Playback Features .................................................................. 6
POWER SYSTEM:
This set operates on voltage of AC110 V – 240 Vd (Rating),
AC90 V– 260 Vd (Operating), 50 Hz / 60 Hz with automatic
switching.
Recording .................................................................................... 7
Basic Recording..................................................................... 7
Recording Features................................................................. 8
Timer Recording ........................................................................... 8
Express Timer Programing...................................................... 8
Checking, cancelling or changing program settings................ 9
Program overlap warning display........................................... 9
Caution on Replaceable lithium battery
The battery used in this device may present a fire or chemical
burn hazard if mistreated. Do not recharge, disassemble, heat
above 100°C or incinerate.
Replace battery with CR2032. Panasonic (Matsushita Electric)
or Maxell is recommended.
Danger of explosion or Risk of fire if the battery is incorrectly
replaced.
Other Functions.......................................................................... 10
Checking tape position ........................................................ 10
Changing display information .............................................. 10
Function settings.................................................................. 10
Ⅲ Dispose of used battery promptly.
Editing....................................................................................... 11
Information on Multi-System Compatibility.................................. 12
Tuner Setting ............................................................................. 14
Specifications............................................................................. 16
Ⅲ Keep away from children.
Ⅲ Do not disassemble and do not dispose off in fire.
IMPORTANT
Ⅲ Please read the various precautions on this page before
installing or operating the recorder.
Ⅲ It should be noted that it may be unlawful to re-record pre-
recorded tapes, records, or discs without the consent of the
owner of copyright in the sound or video recording,
broadcast or cable programme and in any literary, dramatic,
musical, or artistic work embodied therein.
Safety Precautions
The rating plate and the safety caution are on the rear of the unit.
WARNING:DANGEROUS VOLTAGE INSIDE
WARNING:TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
The STANDBY/ON 1 button does not completely shut off
mains power from the unit, but switches operating current on
and off. “`“ shows electrical power standby and “!“ shows ON.
CAUTION
Ⅲ When you are not using the recorder for a long period of
time, it is recommended that you disconnect the power cord
from the mains outlet.
Video tapes recorded with this video recorder in the LP (Long
Play) or EP (Extended Play) mode cannot be played back on a
single-speed video recorder.
Ⅲ Dangerous voltage inside. Refer internal servicing to qualified
service personnel. To prevent electric shock or fire hazard,
remove the power cord from the mains outlet prior to
connecting or disconnecting any signal lead or aerial.
Ⅲ (For HR-V401AS and HR-V201AS)
Use the conversion plug depending on the type of your AC
wall outlet.
— 1 —
Remote control
Buttons, Connectors
and Indicators
Number keys
Front Panel
Cassette loading slot
VIDEO/AUDIO input connectors
* For HR-V400AG and
HR-V401AS only
Infrared beam
receiving window
Display panel
Timer mode indicator
Play indicator
Record
indicator
REVIEW indicator
Channel and auxiliary
input/Clock time
* Not function with this recorder.
On-screen display
If you press
(OK) on the remote control when “O.S.D.” is set to
“ON” (੬ 11), you can see the current recorder status on the TV
Rear Panel
screen. After about 5 seconds, indications other than the time
counter disappear. To clear the time counter, press
(OK) again.
Mains power cord
The indications are not recorded even if the recorder is in the
recording mode.
J
I
H
G
A
B
C
PR. 12
SP
NTSC 3.58
23 : 59
31. 12. 03
F
E
+
+
+
+
0
– 1 : 23 : 45
D
A Channel and auxiliary input
B Clock time
C Current day/month/year
D Time counter
E Tape position
F Tape direction
G Colour system indicator
H Tape speed
I Recorder operation mode
J Cassette mark
— 3 —
Basic Connections
Make sure the package contains all of the accessories listed in
“Specifications” (੬ 16).
Initial Settings
A Check contents
Video Channel Set
Video channel (RF output channel) is the channel on which your TV
receives picture and sound signals from the video recorder through
the RF cable. Before performing the following steps, make sure the
recorder’s power is off and there is no cassette inserted in the
recorder.
B Situate recorder
Place the recorder on a stable, horizontal surface.
C Connect recorder to TV
If you have connected the video recorder to your TV via the
provided RF cable only (RF connection)...
A Hold down 0 on the recorder until
the display panel shows the following.
B Press PR r or t on the remote control
to set appropriate TV system that
matches the system of TV being used
(refer to the table below).
TV aerial cable
1:B/G 2:D/K 3:I 4:H
Major Countries/Areas
TV System
New Zealand, Kuwait, U.A.E., Indonesia,
Singapore, Thailand, Malaysia, Iran, Saudi
Arabia, Egypt, Morocco, Lebanon, Iraq
B/G
China, Mongolia, Russia
Hong Kong
D/K
I
Mains power cord
Australia
H
C Set your TV to UHF channel 36.
● If the two vertical white bars appear clearly on
the screen as shown on the right, press OK or e
and then go to step D.
Back of recorder
Mains outlet
● Ifthetwoverticalwhitebarsdonotappearclearly,
press OK and then PR r or t to set the recorder to a vacant
channel between 28 and 60 which is not occupied by any local
station in your area.
(Ex.) If channel 50 is available in your area...
To AV input
connectors
Then set your TV to UHF channel 50 and check if the two vertical
white bars appear clearly on the screen; if so, go to step D. If not,
re-set the recorder to another vacant channel and try again.
D Press OK or e to finish video channel set.
AV cable
(not supplied)
If you have connected the video recorder to your TV via both the
provided RF cable and an AV cable (AV connection)...
A Hold down 0 on the recorder until
RF cable
(supplied)
To aerial terminal
the display panel shows the following.
TV
B Press OK or e, then press PR t until
the display panel shows the following.
Now the video channel is set to off (– –).
C Press OK or e to finish video channel
set.
RF Connection
A Disconnect the TV aerial cable from the TV.
B Connect the TV aerial cable to the ANT. IN terminal on the
rear of the recorder.
C Connect the supplied RF cable between the RF OUT terminal
on the rear of the recorder and the TV’s aerial input terminal.
If Auto Set Up or Tuner Set has not previously been performed,
the Language Select screen appears and Auto Set Up function
takes place automatically.
AV Connection
(improves picture quality during tape playback.)
If your TV is equipped with AV input connectors
A Connect the aerial, recorder and TV as shown in the
illustration.
B Connect an AV cable between the AUDIO/VIDEO OUT
connectors on the rear of the recorder and the AV input
connectors on the TV.
● Even if you are using AV cables to connect your recorder to
your TV, you must also connect it using the RF cable. This will
ensure that you can record one show while watching another.
D Connect recorder to mains
Plug the mains power cord into a mains outlet.
— 4 —
– Initial Settings –
Auto Set Up
Language Setting
The Auto Set Up function simplifies installation by guiding you
through the procedures of setting the language, clock and tuner
channels — simply follow the on-screen menus that appear.
● Turn on the recorder and the TV, and set your TV to its AV mode
or video channel.
MAIN MENU
A Access Main Menu screen, then
FUNCTION SET
TUNER SET
INITIAL SET
Initial Set screen
Press MENU on the remote control. Press
PR r/t to place the pointer next to
“INITIAL SET”, then press OK or e.
[
/
]
A Select language
Press PR r/t to place the pointer next to your desired language
(English, Russian or Arabic), then press OK or e.
● The Clock Set screen appears.
[MENU] : EXIT
B Access Language Select screen
Press PR r/t to place the pointer next to “LANGUAGE”, then
press OK or e.
B Set time
CLOCK SET
C Select language
INITIAL SET
Press PR r/t to set the hour, then press
TIME
DATE
01.01
YEAR
03
Press PR r/t to place the pointer next to
the language of your choice (English,
Russian or Arabic), then press OK or e.
Press MENU to return to normal screen.
CLOCK SET
LANGUAGE
0 : 00
OK or e.
● Press and hold either button to delay or
advance the time by 30 minutes.
[
/
]
[
/
]
[MENU] : EXIT
[MENU] : EXIT
C Set date
Press PR r/t to set the date, then press OK or e.
● Press and hold either button to change the date by 15 days.
Clock Setting
D Set year
Press PR r/t to set the year, then press MENU.
A Access Main Menu screen, then Initial Set screen
Press MENU on the remote control. Press PR r/t to place the
pointer next to “INITIAL SET”, then press OK or e.
E Select TV system
Press PR r/t to place the pointer next to the appropriate TV
B Access Clock Set screen
INITIAL SET
system (refer to the table below).
Press PR r/t to place the pointer next to
CLOCK SET
LANGUAGE
“CLOCK SET”, then press OK or e.
Major Countries/Areas
TV System
Australia, New Zealand, Kuwait, U.A.E.,
Indonesia, Singapore, Thailand, Malaysia,
Iran, Saudi Arabia, Egypt, Morocco,
Lebanon, Iraq
[
/
]
[MENU] : EXIT
B/G
C Set time, date and year
CLOCK SET
TIME
0 : 00
DATE
01.01
YEAR
03
Press PR r/t until the desired time
appears, then press OK or e. Set the date
and year in the same way.
China, Mongolia, Russia
Hong Kong
D/K
I
● Holding PR r/t changes the time in
30-minute intervals, or changes the date
in 15-day intervals.
[
/
]
[MENU] : EXIT
F Start auto channel set
Press OK or e.
AUTO CH SET
PLEASE WAIT
● Receivable channels in your area are
automatically assigned to the PR +/–
buttons, and non-receivable channels
are skipped.
D Start clock
Press MENU and normal screen appears.
NOTE:
START
FINISH
– – – – – – –
I
I
I
I
I
I
I
I
I
I
I
I
If the year digits are automatically cleared, it is possible that you
have input February 29th in a non-leap year. Input the correct
data.
● When Auto Set Up is completed, the
lowest position number will appear on the front display panel. If
“SCAN COMPLETED–NO SIGNAL–” is displayed on the screen,
make sure that the aerial cable is connected to the recorder
properly and press OK on the remote control. The recorder will
try Auto Set Up again.
To make corrections any time during the process
Press OK or e repeatedly until the item you want to change
blinks, then press PR r/t.
— 5 —
Playback
Basic Playback
Turn on the TV and select the video channel or AV mode.
Reverse
Forward
Reverse
slow
motion
1 step
Reverse
search
3 steps
Reverse
play
Slow
motion
1 step
Normal
play
Forward
search
4 steps
A Load a cassette
When the tape is not running
Rewind/fast-forward
Press 3 or 5.
Eject the cassette
Make sure the window side is up, the rear label side is facing you
and the arrow on the front of the cassette is pointing towards the
recorder.
● Do not apply too much pressure when inserting.
● The recorder turns on, and the counter on the on-screen display
is reset, automatically.
Press 0.
● You can also eject the cassette when the recorder is turned off.
Turn off the recorder
● Select the appropriate colour system with “PAL/MESECAM” and
“NTSC” in Function settings (੬ 10).
Press 1.
● If the cassette’s record safety tab has been removed, playback
begins automatically.
Playback Features
B Start playback
Press 4.
Adjusting tracking condition
— tracking adjustment
ATTENTION
In the search, still, slow-motion or frame-by-frame playback
mode,
Automatic tracking adjustment
● the picture will be distorted.
● the noise bars will appear.
● there may be a loss of colour
Whenever you insert a tape and start playback, automatic tracking
starts working and continuously analyzes the signal to enable
optimum picture quality during playback.
Manual tracking adjustment
If automatic tracking cannot eliminate noises well during
playback, follow the procedures below.
During playback
Stop playback
A Press p(SP/LP/EP) on the remote control during playback to
Press 8 on the remote
control.
OR Press 0 on the recorder.
activate manual tracking.
B Press PR r/t or PR +/– to eliminate the noises. Press it briefly
for a fine adjustment, or press and hold for a coarse
adjustment.
Pause playback and view still picture
Press 9.
● Press 4 to resume normal playback.
● If there is vertical jitter, press PR r/t on the remote control or
PR +/– on the recorder to correct the picture.
● Press p(SP/LP/EP) again to reactivate automatic tracking.
Automatic operations after rewinding
— Next Function Memory
Pause and Frame-by-Frame playback
Press 9 to pause, then press w or e (or 9) repeatedly.
● Press 4 to resume normal playback.
The Next Function Memory “tells” the recorder what to do after
rewinding is completed. Ensure that the recorder is in stop mode.
● For Automatic Playback Start
Picture Search
Press 3, then press 4 within 2 seconds.
● For Automatic Power Off
Press 3, then press 1 within 2 seconds.
● For Automatic Timer Standby
Press 3, then press # within 2 seconds.
Press 3 or 5. Press 3 or 5 again to perform high-
speed search.
● Each time you press 3 or 5, the search speed changes
between low-speed and high-speed.
● Press 4 to resume normal playback.
NOTE:
Variable Speed Search (including slow-motion)
It is not possible to select the Automatic Timer Standby function if
the cassette’s record safety tab is removed.
Press w or e repeatedly.
● Press 4 to resume normal playback.
● Each time you press w or e, the playback speed changes. To
decrease the speed during picture search, press the opposite
direction button repeatedly.
● During still picture, press and hold e to start forward (or w to
start reverse) slow motion playback. When you release the
button, still picture resumes. During still picture, holding 9 for
more than 2 seconds also starts forward slow motion playback.
If you press 9 again, still picture resumes.
● During slow motion playback, some noise may appear on the
TV screen. Press PR r/t on the remote control or PR +/– on
the recorder to eliminate the noise.
— 6 —
– Playback –
Playing back tape repeatedly (100 times)
Recording
— Repeat Play
During playback, press and hold 4 for more than 5 seconds. The
play indicator ($) on the display panel starts blinking slowly. To
stop playback, press 8 on the remote control or 0 on the
recorder.
Accidental erasure prevention
To prevent accidental recording on a
recorded cassette, remove its record
safety tab. To record on it later, cover
the hole with adhesive tape.
NOTE:
Record safety tab
Pressing 4, 3, 5 or 9 also cancels repeat playback.
Basic Recording
Turn on the TV and select the video channel or AV mode.
Locating beginning of recordings
— Index Search
Index codes are placed on the tape at the beginning of each
recording when recording on this recorder.
A Load a cassette
A While the tape is not running, press w or e on the remote
Make sure the record safety tab is intact. If not, cover the hole
with adhesive tape before inserting the cassette.
control to start search.
B To access a recording of 2 to 9 index
6 2
● The recorder turns on, and the counter is reset, automatically.
● Select the appropriate colour system with “PAL/MESECAM” and
“NTSC” in Function settings (੬ 10).
codes away, press w or e repeatedly
until the correct number is displayed
on the screen (only if “O.S.D.” is set to
“ON” (੬ 11)). Playback begins
automatically when the desired
recording is located.
B Select recording channel
Press PR r/t or the Number keys on the remote control or
PR +/– on the recorder.
NOTE:
Beginning of the
current program
recorded
Beginning of the
2nd next program
recorded
Current
position on
the tape
You can select channel in the stop mode, recording pause mode
or during rewind/fast-forward.
C Set tape speed
Previous
program
recorded
Next
program
recorded
Press p(SP/LP/EP). The current setting for the tape speed
appears on the display panel and the screen for about 5 seconds.
Press p(SP/LP/EP) again to change the setting while tape speed
is displayed.
2nd next
D Start recording
On the recorder, press 7. Or on the remote control, while holding
7, press 4.
NOTE:
Locating beginning of timer recordings
If the tape reaches its end during recording, the recording stops
and “ ⅜” and “ $” blink on the display window. Press 0 on
the recorder to eject the cassette or press 3 on the remote
control to rewind the tape.
— Instant Review
After ensuring that the recorder is turned off and that the timer
mode is disengaged, press REVIEW on the remote control.
● The recorder turns on, and rewinds to the index code indicating
the beginning of the last timer-recorded program, then begins
playback automatically.
● You can access a program of 2 to 9 index codes away from the
current position on the tape. If, for example, you have
5 programs recorded and you want to watch the third one, press
REVIEW three times.
During recording
Pause recording
Press 9.
● Press 4 to resume recording.
● You can select channel in the recording pause mode.
● The Instant Review function will also operate if the recorder is
turned on.
Stop recording
Press 8 on the remote
control.
OR Press 0 on the recorder.
Skipping unwanted portions
— Skip Search
Press 30 SEC
on the remote control once to 4 times during
playback. Each press initiates a 30-second period of high speed
playback (up to 2 minutes). When the specified portion of the tape
is skipped, normal playback resumes automatically. To return to
normal playback during Skip Search, press 4.
— 7 —
– Recording –
Recording Features
Timer Recording
Up to 8 timer recording programs can be made using Express
timer programing method as far as a year in advance.
Specifying recording length
NOTES:
— Instant Timer Recording (ITR)
● If all the 8 programs have already been set, “PROGRAM FULL”
appears on the TV screen.
During recording, press 7 on the recorder repeatedly until the
recording length you want appears on the display panel. The
record indicator (⅜) on the display panel starts blinking.
● Each time you press the button, recording length increases in
30-minute intervals (up to 6 hours).
● After timer recording is completed, the recorder turns off
automatically.
● You can program the timer recording while a regular recording
is in progress; the menu screens will not be recorded.
● If the tape reaches its end during recording, the recording stops
and “ #“, “ ⅜“ and “ $“ on the front display panel blink. Press
# to disengage timer then press 0 on the recorder to eject
the cassette or press 1 then press 3 to rewind the tape.
● The recorder shuts off after recording is finished.
● To cancel an ITR, press 8 on the remote control or 0 on the
recorder.
Watching one program while recording another
Express Timer Programing
Once recording is in progress, all you need to do is to set the
channel controls on the TV for the station you wish to view.
● The programme selected with the TV’s channel controls appears
on the TV screen while the one selected with the PR r/t on
the remote control or PR +/– buttons is recorded on the tape.
● Remember, the clock must be set before you can program the
timer.
● Load a cassette with the record safety tab intact. The recorder
turns on, and the counter is reset, automatically.
● Select the appropriate colour system with “PAL/MESECAM” and
“NTSC” in Function settings. (੬ 10)
Recording Resume Function
If there is a power outage during recording (or Instant Timer
Recording, or timer recording), the recording will resume
automatically when the power is restored to the recorder. (No
setting is required for this function.)
NOTE:
If a power outage exceed the recorder’s memory backup time,
Recording Resume Function does not work.
2
4
A
2
3
A Press PROG on the remote control to access the Program
screen.
B Press START
and/or “4”), STOP
keys “2” and/or “5”), DATE
(number keys “3” and/or “6”) or PR
repeatedly to enter the start
time, stop time, date or channel.
● Press and hold START
(number keys “1” and/or “4”) or
/
(number keys “1”
– P1 –
START
21:00
STOP
/
(number
–:– –
/
SP
DATE
– –.– –
[+/–]
[PROG] : EXIT
TV PROG
– –
/
/
STOP
/
(number keys “2” and/or “5”) to increase the
time in 30-minute intervals.
● To set the tape speed, press p(SP/LP/EP).
● To timer-record daily (Monday–Friday) or weekly serials,
press DAILY (number key 8) or WEEKLY (number key 9).
Pressing the button again makes the “DAILY” or “WEEKLY”
display disappear.
C Press OK or PROG.
● If “PROGRAM OVERLAPPED” appears, see “Program
overlap warning display” (੬ 9).
D Press #. The recorder turns off automatically and “#” is
displayed on the display panel.
— 8 —
– Timer Recording –
To use the recorder while it is in
timer recording standby mode
Program overlap warning display
If “PROGRAM OVERLAPPED” appears, you have another
program overlapping the program you have just made. The
Program Check screen appears and conflicting programs will start
blinking.
Press #, then press 1. After you use the recorder, press # again
to put the recorder into timer recording standby mode.
PR START STOP CH DATE
1
2
3
4
5
6
7
8
8:00 10:00
10:00 10:45
11:30 13:00
3
2
1
24.04
25.04
25.04
PROGRAM OVERLAPPED
Checking, cancelling or changing
program settings
9:00 10:00 92 DAILY
[
/
]
[PROG] : EXIT
Example:
A Disengage timer
Program 1 (you have just made) and Program 4 overlap each
other.
Press #, then press 1.
● When “AUTO TIMER” is set to “ON” (੬ 11), you do not have
to press #.
A Select program to modify
Press PR r/t, then press OK or e.
● You can only select one of the
overlapping programs.
● If you do not mind this overlap, press
PROG to finish the timer program
setting. The program starting earlier or
PR START STOP CH DATE
1
2
3
4
5
6
7
8
8:00 10:00
10:00 10:45
11:30 13:00
3
2
1
24.04
25.04
25.04
B Access Program Check screen
PR START STOP CH DATE
1
2
3
4
5
6
7
8
8:00 10:00
10:00 10:45
11:30 13:00
3
2
1
24.04
25.04
25.04
9:00 10:00 92 DAILY
Press ".
● When the weekly serials are
programmed, a day of the week appears.
When the daily serials are programmed,
“DAILY” appears.
[
/
]
[PROG] : EXIT
[
] : NEXT
program with the lower program number will be recorded.
C Access Program screen
Press " again. Each time you press ",
the next program’s Program screen
appears.
– P1 –
START
STOP
10:00
B Cancel or change program setting
To cancel a program, press & when the
Program screen you do not want is shown.
To change a program, press the
– P1 –
8:00
START
9:00
STOP
10:00
SP
SP
DATE
24.04
TV PROG
3
DATE
25.04
] : DELETE
TV PROG
92
[+/–]
appropriate button: START
keys “1” and/or “4”), STOP
keys “2” and/or “5”), DATE
keys “3” and/or “6”), PR
/
(number
[
] : NEXT
[
/
/
(number [PROG] : EXIT
D Cancel or change program setting
(number
To cancel a program, press & when the Program screen you do
/
, DAILY (number key 8), WEEKLY
not want is shown.
(number key 9) and/or p(SP/LP/EP) when the Program screen
on which you want to make changes is shown, then press OK
or e.
● If the overlap is not yet solved, the conflicting programs will be
shown on the Program check screen. Repeat the above steps
again.
To change a program, press the appropriate button: START
/
(number keys “1” and/or “4”), STOP
/
(number keys “2”
and/or “5”), DATE (number keys “3” and/or “6”), PR
/
/
,
DAILY (number key 8), WEEKLY (number key 9) and/or p(SP/
LP/EP) when the Program screen on which you want to make
changes is shown.
E Return to normal screen
Press " repeatedly until no Program screen is shown.
F Reengage timer recording standby mode
Press #. The recorder turns off automatically and “#” is displayed
on the display panel.
● When “AUTO TIMER” is set to “ON” (੬ 11), the timer
recording standby mode automatically resumes when you turn
off the recorder.
— 9 —
Ⅵ B.E.S.T. — ON / OFF
Other Functions
When B.E.S.T. (Biconditional Equalized Signal Tracking) system is
set to “ON”, this recorder checks the condition of the tape in use
during playback and recording, and compensates to provide the
highest-possible pictures. This takes place whenever you play
back a tape or start recording after inserting a tape.
Checking tape position
NOTE:
When you change the recorder operation
mode from the stop mode to fast forward
or rewind mode, or when you perform an
Index Search or Instant Review, the tape
The recorder checks the tape condition for about 7 seconds, then
starts recording. To make sure you record the desired scene or
program completely, perform the following steps:
A Press and hold 9, and press 7. After about 7 seconds, the
recorder re-enters Record Pause mode.
+
+
+
+
0
position indicator appears.
The position of “q” in relation to “0”
(beginning) or “+” (end) shows you where
you are on the tape.
1:23:45
B Press 4 to start recording.
● Set “O.S.D.” to “ON” (੬ 11).
Ⅵ PICTURE CONTROL — AUTO(NORM) / EDIT / SOFT
This function helps you to adjust the playback picture quality
according to your preference.
AUTO (NORM): Normally select this. Picture quality is adjusted
automatically. When “B.E.S.T.” is “OFF”, “NORM” will appear
instead of “AUTO”.
EDIT: Minimizes picture degradation during editing (recording and
playback).
SOFT: Reduces image coarseness when viewing overplayed tapes
containing much noise.
Changing display information
Each time you press – –:– –, the display panel shows
the channel number and the clock time alternatively.
● You can change display in the stop, recording or
during rewind/fast-forward high-speed search.
● When “O.S.D.” is set to “ON” (੬ 11) and – –:– –
on the remote control is pressed, time counter will
appear on the TV screen. To reset the time counter, press 0000
on the remote control.
NOTE:
Select “EDIT” when you are editing tapes. After you finish editing
the tapes, select “AUTO”.
Function settings
screen.
● Turn on the recorder and the TV, and set your TV to its AV mode
or video channel.
Ⅵ PAL/MESECAM — AUTO / PAL / MESECAM
Select the appropriate colour system for recording or playback.
AUTO: Usually set to this mode. The appropriate colour system
(PAL or MESECAM) will be selected depending on the playback or
recording signals.
If the “AUTO” mode does not work properly, select either of the
following manual modes.
PAL: To record PAL signals, or playback a PAL tape.
MESECAM: To record SECAM signals, or playback a SECAM or
MESECAM tape.
You can use the other useful function settings on the Function Set
MAIN MENU
A Access Main Menu screen, then
FUNCTION SET
Function Set screen
TUNER SET
INITIAL SET
Press MENU on the remote control. Press
PR r/t to place the pointer next to
NOTES:
“FUNCTION SET”, then press OK or e.
[
/
]
● SECAM signals will always be recorded as MESECAM. Select
“AUTO” or “MESECAM” when recording SECAM signals.
● When playing back a SECAM tape, select “AUTO” or
“MESECAM”. The playback picture will always be
monochrome.
[MENU] : EXIT
B Select Function
FUNCTION SET
B.E.S.T.
ON
AUTO
PICTURE CONTROL
PAL/MESECAM
NTSC
Press PR r/t to place the pointer next to
AUTO
the function you want to set.
NTSC3.58
OFF
AUTO TIMER
O.S.D.
ON
OFF
AUTO SP LP TIMER
[
/
]
Ⅵ NTSC — NTSC3.58 / NTSC4.43 / NTSC]PAL
To record NTSC signals or playback a NTSC tape, it will be
necessary to select the appropriate mode.
[MENU] : EXIT
C Change setting
Press OK or e. The default setting is bold in the following table.
NTSC3.58: To record NTSC signals or playback a NTSC tape.
NTSC4.43: To record NTSC4.43 signals or playback a NTSC4.43
tape.
Press MENU to return to normal screen.
NTSC]PAL: To playback a NTSC tape on PAL TV.
NOTES:
● The “NTSC]PAL” mode does not work during recording. In
this mode, NTSC signals will be recorded as NTSC3.58.
● The Menu screen is distorted during playing back a NTSC tape
on PAL TV. Stop playback and access the Menu screen again.
● In the “NTSC4.43” mode, with some TVs, on-screen displays
(Program screen, etc.) may roll up or down and there may be a
loss of colour. When this happens, select the “NTSC3.58”
mode.
— 10 —
– Other Functions –
Ⅵ AUTO TIMER — ON / OFF
Editing
● When this function is set to “ON”:
The timer recording standby mode is automatically engaged when
the recorder is turned off. It is temporarily canceled when the
recorder is turned on. You do not have to press # to engage or
disengage the timer recording standby mode.
● When this function is set to “OFF”:
You have to press # to engage or disengage the timer recording
standby mode.
You can use your recorder as the playback or recording deck. You
can use a camcorder as the source player and your recorder as the
recording deck. Refer also to the other components’ instruction
manuals for connection and its operations.
A Make connections
Example: When using this recorder as the source player
Ⅵ O.S.D. — ON / OFF
This recorder (for playback)
To AUDIO/VIDEO OUT
When this function is set to “ON”, various recorder status
information (on-screen display) appears on the screen.
NOTE:
When you use this recorder as the source player for editing a tape,
be sure to set this function to “OFF”; otherwise, the recorder status
information (on-screen display) will be recorded on the edited
tape.
AV cable
(not supplied)
Ⅵ AUTO SP]LP TIMER — ON / OFF
When this function is set to “ON”, the recorder automatically
switches to LP mode to allow complete recording if there is not
enough tape to record the entire program while timer-recording in
SP mode.
For Example, Recording a PAL-broadcast programme of 210
minutes in length onto a 180-minute tape.
To AV input
Approximately 150 minutes
SP mode
Approximately 60 minutes
LP mode
Another recorder (for recording)
Total 210 minutes
NOTES:
● When using this recorder as the recording deck, connect this
recorder’s AV input connectors to the AV output connectors on
the other recorder. If the source player is monaural, connect the
audio output connector on the source player to the left audio
input connector on this recorder.
● If you have programed the recorder to timer-record 2 or more
programs, do not use this function, but change the tape speed
manually during timer programing.
● There may be some noise and sound disturbance where the tape
speed switches from SP to LP mode on the tape.
● The Auto SP]LP Timer feature is not available during ITR
(Instant Timer Recording), and the feature will not work
properly with any tapes longer than E-180 or with some tapes of
shorter lengths.
B Load cassettes
Insert the playback cassette into the source player and the cassette
to be recorded on into the recording deck.
C Select input mode on recording deck
Select the correct external input on the recording deck. Press AUX
or PR r/t on the remote control or PR +/– on the recorder.
On this recorder (when using this recorder as the recording deck);
Select “L-1” — when connecting the other recorder to the AV
input connectors on the rear panel.
(For HR-V400AG and HR-V401AS)
Select “F-1” — when connecting the other recorder to the AV
input connectors on the front panel.
D Select edit mode
Set the edit mode to “ON” for the recorders if such a mode is
equipped.
● On this recorder, set “PICTURE CONTROL” to “EDIT” (੬ 10).
E Start playback
Press 4 on the source player.
F Start recording
Press 7 on the recording deck.
— 11 —
Information on Multi-System Compatibility
Off-Air Recording
The built-in multi-system tuner is capable of receiving PAL B/G, I and D/K, and SECAM B/G and D/K broadcasts.
Recorded tape
TV system
Multi-system
tuner
(B/G, I, D/K)
NOTE:
This model does not operate in BRAZIL (PAL-M) or ARGENTINA (PAL-N).
Playback
This recorder can play back all 3 types of recorded tape.
Recorded tape
Playback circuit
Multi-system receiver
Built-in
RF converter
K, I, G, H
Multi-system monitor
Manual switching
Manual switching
NOTE:
When viewing NTSC tapes on a PAL TV set:
● The picture may shrink vertically with black bars appearing at the top and bottom of the screen. This is not a malfunction on the part of the
video recorder nor the TV.
● The picture may roll up or down. This can be corrected using the V-HOLD control found on some TVs. (This cannot be corrected if the TV
does not have a V-HOLD control.)
● During search, still, or frame-by-frame playback, the picture will be distorted, and there may be a loss of colour.
ATTENTION:
When this recorder is connected to a multi-system TV, the audio signal may not be heard or may be noisy if the colour system select switch
of the TV is adjusted to the AUTO position. In such a case, set the TV’s colour system select switch to the appropriate position which
corresponds to the TV system you have selected at the TV System Select screen.
— 12 —
– Information on Multi-System Compatibility –
Tape-To-Tape Editing
There are 4 different types of recorded tape, depending on the signal recorded.
Recorded tape
Playback equipment
Dubbed tape
Recording circuit
— 13 —
Manual Channel Set
Tuner Setting
Store channels that were not stored during Auto Set Up or Auto
Channel Set.
IMPORTANT
Perform the following steps only if auto channel set has not been
set correctly by Auto Set Up function or if you have moved to a
different area or if a new station starts broadcasting in your area.
A Access Tuner Set screen
Perform step A of “Auto Channel Set”.
B Access channel list
Your recorder needs to memorise all necessary stations in channel
positions in order to record TV programmes. Auto Channel Set
automatically assigns all receivable stations in your area so that
you can call them up with the PR +/– buttons without going
through any vacant channels.
Press PR r/t to place the pointer next to “CH EDIT”, then press
OK or e.
C Select position
Press PR r/t to place the pointer next to an open channel
position, then press OK or e.
Auto Channel Set
A Access Main Menu screen, then Tuner
D Select band
Press PR r/t to place the pointer next to the band of your
MAIN MENU
choice, then press OK or e to initiate Manual Channel Set.
FUNCTION SET
Set screen
TUNER SET
INITIAL SET
BAND SELECT
VHF L
MANUAL CH SET
Press MENU on the remote control. Press
PR r/t to place the pointer next to
PLEASE WAIT
VHF H
“TUNER SET”, then press OK or e.
[
/
]
[MENU] : EXIT
UHF
VHF L 300MHZ
B Perform Auto Channel Set
TUNER SET
[
/
]
[MENU] : EXIT
[MENU] : EXIT
CH EDIT
Press PR r/t to place the pointer next to
“AUTO CH SET”, then press OK or e.
AUTO CH SET
E Set desired station
The screen to the right appears when a
station is detected.
STORE
[
/
]
CONTINUE
[MENU] : EXIT
If you do not want to store the detected
station...
Press PR r/t to place the pointer next to
“CONTINUE”, then press OK or e.
Channel search will resume.
If you want to store the detected station...
Press PR r/t to place the pointer next to “STORE”, then press
OK or e. The Channel List appears again.
● The blueback screen and the TV picture currently being
broadcast appear alternately for 8 seconds each.
● If you want to store another channel, repeat steps C – E.
● When channel search completes for that band, the Band Select
screen appears again. To set channels for other bands, select
another band and start Manual Channel Set again (੬ step D
and E).
C Select TV system
TV SYSTEM SELECT
[
/
]
B/G
D/K
I
Press PR r/t to place the pointer next to
the appropriate TV system, then press OK
or e.
[MENU] : EXIT
● Auto Channel Set will start.
[
/
]
[MENU] : EXIT
CH FRQ SYS CH FRQ SYS
01 150 BG
02 165 BG
03 195 BG
04 205 BG
05 213 BG
06 221 BG
07 229 BG
AUTO CH SET
PLEASE WAIT
08 237 BG
09 355 BG
10 365 BG
11 374 BG
12 384 BG
START
FINISH
– – – – – – –
[
[
/
/
]
]
[
] : DELETE
: EDIT
I
I
I
I
I
I
I
I
I
I
I
I
[MENU] : EXIT
Press MENU to return to normal screen.
IMPORTANT
F Return to normal screen
Press MENU.
● If no sound accompanies the picture or the audio sounds
unnatural on some channels that have been stored by Auto
Channel Set, the TV system setting for those channels may be
incorrect. Select the appropriate TV system for those channels.
Refer to “TV System Selection — When you see the picture but
the audio can’t be heard or sounds unnatural” (੬ 15).
● Since your recorder memorises all detected stations even if the
reception condition is poor, some of those stored stations may
produce a noisy picture. To delete those stations, refer to
“Delete A Channel” (੬ 15).
— 14 —
– Tuner Setting –
Delete A Channel
Fine-Tuning Channels
A Access Tuner Set screen
Perform step A of “Auto Channel Set” (੬ 14).
A Access Tuner Set screen
Perform step A of “Auto Channel Set” (੬ 14).
B Access channel list
B Access channel list
Press PR r/t to place the pointer next to “CH EDIT”, then press
Press PR r/t to place the pointer next to “CH EDIT”, then press
OK or e.
OK or e.
C Select channel
CH FRQ SYS CH FRQ SYS
C Select channel to fine-tune
CH FRQ SYS CH FRQ SYS
01 150 BG
02 165 BG
03 195 BG
04 205 BG
05 213 BG
06 221 BG
07 229 BG
08 237 BG
09 355 BG
10 365 BG
11 374 BG
12 384 BG
01 150 BG
02 165 BG
03 195 BG
04 205 BG
05 213 BG
06 221 BG
07 229 BG
08 237 BG
09 355 BG
10 365 BG
11 374 BG
12 384 BG
Press PR r/t to until the channel you
Press PR r/t until the channel you want
to tune begins blinking, then press OK
twice.
want to delete begins blinking.
[
[
/
/
]
]
[
] : DELETE
: EDIT
[
/
] : FINE TUNING
: SELECT SYSTEM
[MENU] : EXIT
● The “FRQ” number for that channel
starts blinking.
[MENU] : EXIT
D Delete channel
CH FRQ SYS CH FRQ SYS
D Perform tuning
01 – – – – –
02 165 BG
03 195 BG
04 205 BG
05 213 BG
06 221 BG
07 229 BG
08 237 BG
09 355 BG
10 365 BG
11 374 BG
12 384 BG
Press &. The channel directly beneath the
cancelled one moves up one line.
Press PR r/t until the picture becomes clearer, then press OK
or e.
● Repeat steps C and D as necessary.
● Repeat steps C and D as necessary.
[
/
]
[
] : ADD
E Return to normal screen
Press MENU.
[MENU] : EXIT
E Return to normal screen
Press MENU.
Swap Channel Positions
TV System Selection — When you see the picture
Example: To swap CH03 and CH09.
but the audio can’t be heard or sounds unnatural
A Access Tuner Set screen
Perform step A of “Auto Channel Set” (੬ 14).
A Access Tuner Set screen
Perform step A of “Auto Channel Set” (੬ 14).
B Access channel list
B Access channel list
Press PR r/t to place the pointer next to “CH EDIT”, then press
Press PR r/t to place the pointer next to “CH EDIT”, then press
OK or e.
OK or e.
C Select position (e.g. 03)
Press PR r/t until the section of CH “03”
begins blinking, then press OK or e.
● Only “03” will blink.
CH FRQ SYS CH FRQ SYS
01 150 BG
02 165 BG
03 195 BG
04 205 BG
05 213 BG
06 221 BG
07 229 BG
08 237 BG
09 355 BG
10 365 BG
11 374 BG
12 384 BG
C Select channel
CH FRQ SYS CH FRQ SYS
01 150 BG
02 165 BG
03 195 BG
04 205 BG
05 213 BG
06 221 BG
07 229 BG
08 237 BG
09 355 BG
10 365 BG
11 374 BG
12 384 BG
Press PR r/t until the channel you want
to change its TV system begins blinking,
then press OK three times.
[0 – 9] : INPUT CH
: FINE TUNING
[MENU] : EXIT
[
/
] : SELECT SYSTEM
: OK
[MENU] : EXIT
● The “SYS” display for that channel starts
blinking.
D Select position (e.g. 09)
Press Number keys to input “0” and “9”.
● The two selected channels will be
swapped.
● To cancel the channel swapping,
press w.
CH FRQ SYS CH FRQ SYS
01 150 BG
02 165 BG
03 355 BG
04 205 BG
05 213 BG
06 221 BG
07 229 BG
08 237 BG
09 195 BG
10 365 BG
11 374 BG
12 384 BG
D Select TV system
Press PR r
/
t
to select the appropriate TV system (BG
]
DK
]
I).
Then press OK or e.
● Repeat steps C and D as necessary.
[
] : CANCEL
: OK
[MENU] : EXIT
E Return to normal screen
Press MENU.
E Store new positions
Press OK or e.
● Repeat steps C – E as necessary.
F Return to normal screen
Press MENU.
— 15 —
TUNER/TIMER
TV channel storage
capacity
Tuning system
Channel coverage
VHF
Specifications
GENERAL
Power requirement
: 99 positions (+AUX position)
: Frequency synthesized tuner
: (Low) 42 MHz – 175 MHz
Rating
:
AC 110 V – 240 Vd, 50 Hz/60 Hz
(High)175 MHz – 470 MHz
: 470 MHz – 870 MHz
: UHF channels (Adjustable E28 – E60)
: Approx. 10 min.
Operating
Power consumption
Temperature
: AC 90 V – 260 Vd, 50 Hz/60 Hz
: 14 W
UHF
Aerial output
Memory backup time
Operating
: 5°C to 40°C
Storage
Operating position
Dimensions (W x H x D) : 360 mm x 94 mm x 265 mm
:
–20°C to 60°C
ACCESSORIES
Provided accessories
: Horizontal only
: RF cable,
Lithium battery CR2032,
Infrared remote control unit,
Conversion plug*
Weight
Format
Maximum recording time
(SP)
: 2.7 kg
: VHS standard
: 240 min. with E-240 video cassette
(PAL/MESECAM)
: 160 min. with T-160 video cassette
(NTSC)
: 480 min. with E-240 video cassette
(PAL/MESECAM)
: 480 min. with T-160 video cassette
(NTSC)
*Not provided in certain areas.
Specifications shown are for SP mode unless specified otherwise.
E. & O.E. Design and specifications subject to change without
notice.
(LP)
(EP)
VIDEO/AUDIO
Signal system
: PAL-type colour signal and CCIR
monochrome signal, 625 lines
50 fields
NTSC colour and EIA monochrome
signals, 525 lines/60 fields
:
Recording system
: HR-V400AG/V401AS
DA-4 (Double Azimuth) head helical
scan system
:
HR-V207AG/V200AG/V201AS/V200AA
Rotary 2 head helical scan system
Signal-to-noise ratio
Horizontal resolution
: 45 dB
: 250 lines (PAL/MESECAM)
: 220 lines (NTSC)
: 70 Hz to 10,000 Hz
Frequency range
Input/Output
: HR-V400AG/V401AS
RCA connectors (IN x 2, OUT x 1)
:
HR-V207AG/V200AG/V201AS/V200AA
RCA connectors (IN x 1, OUT x 1)
EN
— 16 —
|