MICRO COMPONENT SYSTEM
UX-NB7DAB
—Consists of CA-UXNB7DAB and SP-UXNB7DAB
INSTRUCTIONS
GNT0065-025A
[B]
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions below.
3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a
height of 10 cm or more.
Front view
Side view
15 cm
15 cm
15 cm
15 cm
1 cm
1 cm
15 cm
10 cm
SP-UXNB7DAB CA-UXNB7DAB SP-UXNB7DAB
CA-UXNB7DAB
About the cooling fan
A cooling fan is mounted on the rear panel of the unit to prevent abnormal temperature inside the unit, thus
assuring normal operation of the unit.
Information for Users on Disposal of Old Equipment
[European Union]
This symbol indicates that the electrical and electronic equipment should not be disposed as
general household waste at its end-of-life. Instead, the product should be handed over to the
applicable collection point for the recycling of electrical and electronic equipment for proper
treatment, recovery and recycling in accordance with your national legislation.
By disposing of this product correctly, you will help to conserve natural resources and will
help prevent potential negative effects on the environment and human health which could
otherwise be caused by inappropriate waste handling of this product. For more information
about collection point and recycling of this product, please contact your local municipal office,
your household waste disposal service or the shop where you purchased the product.
Attention:
This symbol is only
valid in the European
Union.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national
legislation.
(Business users)
obtain information about the take-back of the product.
[Other Countries outside the European Union]
If you wish to dispose of this product, please do so in accordance with applicable national
legislation or other rules in your country for the treatment of old electrical and electronic
equipment.
The model information is located on the bottom.
G-2
Contents
Precautions ...........................................................2
Getting Started.....................................................2
Supplied Accessories ...............................................................2
Prepare the Remote Control .................................................2
Connections................................................................................3
Basic and Common Operations ...........................5
Operating on the System .......................................................5
Display Information..................................................................5
Operating on the Remote Control......................................6
Playing Back Discs ................................................7
To Set a Disc ................................................................................7
Basic Disc Operations ..............................................................7
Playing at Random—Random Play ....................................8
Playing Repeatedly—Repeat Play............................................8
Programming the Playing Order—Program Play
(except for MP3)....................................................................8
Listening to the Radio ..........................................9
Basic Tuner Operations............................................................9
What is DAB system?............................................................. 10
Changing the DAB Information ........................................ 10
Improving the DAB reception............................................ 10
Scanning ensembles............................................................. 10
Receiving FM stations with Radio Data System .......... 11
Changing the Radio Data System Information............ 11
Searching for Programs by PTY Codes
(PTY Search)......................................................................... 11
Switching Temporarily to a Program of Your Choice
Automatically...................................................................... 12
Presetting Stations and Services ...................................... 12
Connecting a Portable Audio Device ................13
Playing back a portable audio device............................. 13
Recording to a portable audio device ............................ 14
Setting the Clock and Daily Timer.....................15
Setting the Clock.................................................................... 15
Setting the Daily Timer......................................................... 15
Learning More about This System.....................16
Troubleshooting .................................................17
Maintenance .......................................................18
Specifications......................................................18
Description of the PTY codes for Radio Data
System and DAB ..............................................19
1
Precautions
Notes on the power cord
Notes on installation
• Select a place which is level, dry and neither too hot nor
too cold between 5˚C and 35˚C.
• Do not install the System in a place subject to vibrations.
• Do not put heavy objects on the System.
• When you are away on travel or otherwise for an
extended period of time, remove the plug from the
wall outlet. A small amount of power (2.5 W) is always
consumed while the power cord is connected to the
wall outlet.
• When unplugging the System from the wall outlet,
always pull the plug, not the power cord.
• Do not handle the power cord with wet hands.
• Disconnect the power cord before cleaning the System
or moving the System.
• Do not alter, twist or pull the power cord, or put
anything heavy on it, which may cause fire, electric
shock, or other accidents.
• If the cord is damaged, consult a dealer and have the
power cord replaced with a new one.
To prevent malfunction or damage of the System
• Do not insert any metallic objects, such as wires,
hairpins, coins, etc. into the System.
• Do not block the vents.
To clean the cabinet
• Use a soft cloth. Follow the relevant instructions on the
use of chemically-coated cloths.
• Do not use benzene, thinner or other organic solvents
and disinfectants. These may cause deformation or
discoloring.
There are no user-serviceable parts inside. If
anything goes wrong, unplug the power cord
and consult your dealer.
Avoid moisture, water, dust, and high temperatures
• Do not place the System in moist or dusty places.
• If water gets inside the System, turn off the power and
remove the plug from the wall outlet, then consult your
dealer. Using the System in this state may cause a fire or
electrical shock.
• Do not expose the System to direct sunlight or place it
near a heating device.
Getting Started
Supplied Accessories
After unpacking, check to be sure that you have all the following items. The number in parentheses indicates the
quantity of each piece supplied.
• Remote control (x 1)
• FM antenna (x 1)
• DAB antenna (x 1)
• Lithium coin battery CR2025 (x 1) (The battery has
been installed when shipped from the factory.)
• AM loop antenna (x 1)
If anything is missing, consult your dealer immediately.
NOTES
Prepare the Remote Control
• Store the battery in a place where children cannot
reach. If a child accidentally swallows the battery,
consult a doctor immediately.
When you use the remote control for the first time, pull
out the insulation sheet.
• Do not recharge, short, disassemble or heat the battery
or dispose of it in a fire. Doing any of these things may
cause the battery to give off heat, crack, or start a fire.
• Do not leave the battery with other metallic materials.
Doing this may cause the battery to give off heat, crack,
or start a fire.
Insulation sheet
• When throwing away or saving the battery, wrap it in
tape and insulate; otherwise, the battery may start to
give off heat, crack, or start a fire.
• Do not poke the battery with tweezers or similar tools.
Doing this may cause the battery to give off heat, crack,
or start a fire.
Replacing the Battery in the Remote Control
Insert the battery into the remote control by matching
the polarity (+ and –) correctly.
Lithium coin battery
(product number: CR2025)
• Dispose of battery in the proper manner, according to
federal, state, and local regulations.
CAUTION:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
2
Connections
Do not connect the AC power cord until all other connections have been made.
NOTES
• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. Also, keep
the antennas away from metallic parts of the System, connecting cords, and the AC power cord. This could cause
poor reception.
• If the cords are covered with vinyl, remove the vinyl to expose the tip of the cord by twisting the vinyl.
DAB antenna (supplied)
For better DAB reception
Disconnect the supplied DAB antenna, and connect an active
antenna.
(See“Improving the DAB reception”on page 10.)
Active antenna
(not supplied)
Extend the wire so that you can
receive your desired ensembles.
FM antenna (supplied)
Extend it so that you can
obtain the best reception.
PHONES
SPEAKERS
RIGHT
LEFT
COAXIAL
DAB
LOOP
ANTENNA
AM EXT
IMPEDANCE
MIN
To connect the speaker cords
Make sure the both speakers are connected
correctly and firmly.
To a wall outlet
Plug the AC power cord only after
all connections are complete.
When connecting the speaker cords, match the
polarity of the speaker terminals: white cord to (+)
and white cord with black stripe to (–).
3
To connect the AM loop antenna
1 Hold
2 Insert
3 Release
AM loop antenna (supplied)
Turn it until the best reception is obtained.
To assemble the AM loop antenna
For better FM/AM reception
Outdoor FM antenna
(not supplied)
Disconnect the supplied FM antenna,
and connect to an outdoor FM antenna
using a 75 wire with coaxial type
connector (IEC or DIN45325).
Vinyl-covered wire (not supplied)
AM loop antenna
Keep it connected.
Extend it horizontally.
NOTES
• DO NOT connect more than one speaker
to each terminal.
• DO NOT allow the conductor of the
speaker cords to be in touch with the
metallic parts of the System.
2 Insert
3 Release
1 Hold
4
Basic and Common Operations
Operating on the System
Using Headphones
To
Press
Be sure to turn down the
volume before connecting
or wearing the headphones.
• Connecting the headphones
will deactivate the speakers.
Turn on or off
(standby) the power
The standby lamp on the System turns off/on.
See “Playing Back Discs”on page 7.
Select a source*
See “Listening to the Radio”on page 9.
See “Connecting a Portable Audio Device”
on page 13.
You can adjust the volume level from level 0
(VOL MIN) to level 31 (VOL MAX).
Adjust the volume
* You can operate the source select buttons on the
System only touch lightly, because these buttons are
“touch sensor panel.”
If you touch any one of these buttons, they lights in
orange briefly.
NOTE
DO NOT turn off (standby) the System with the volume
set to an extremely high level; Otherwise, the sudden
blast of sound can damage your hearing, speakers and/or
headphones when you turn on the System or start
playback.
STANDBY lamp
Display Information
Disc play mode indicators (See page 8.)
Tuner mode indicators
(See page 9 and 12.)
Timer mode indicators
(See page 6 and 15.)
QP Link indicator
(See page 13.)
Main Display
AHB PRO and A.STBY indicator (See page 6.)
5
Operating on the Remote Control
To
Press
Turn on or off
(standby) the power
The standby lamp on the System turns off/on.
See “Playing Back Discs”on page 7.
Select a source
See “Listening to the Radio”on page 9.
See “Connecting a Portable Audio Device”on
page 13.
You can adjust the volume level from level 0
(VOL MIN) to level 31 (VOL MAX).
Adjust the volume
Drop the volume in
a moment
To restore the volume, press again, or adjust the
volume level.
AHB PRO indicator appears on the display.
Reinforce the bass
sound
To cancel this function, press again.
Press once to adjust the bass level or press twice
to adjust the treble level.
Adjust the tone
(Bass/Treble)
Then press VOLUME + to increase the level or
press VOLUME – to decrease it.
• You can adjust the bass and treble level from
–3 to +3.
Press when the System is turned on.
Changing the
display brightness
To cancel this function, press again.
Point to the remote sensor
on the front panel. (The
operating range is approx.
7 m.)
Press and hold for more than 2 seconds when
the System is on standby.
To cancel this function, press and hold for more
Set the Save mode
than 2 seconds again.
• Setting the Save mode allows you to reduce
power consumption by turning the display off
while on standby.
Changing the
display information
(Clock and Source)
Press briefly (except for FM and DAB mode).
For setting the clock, see page 15.
Press and hold until A.STBY indicator appears on
the display.
Turn off the System
automatically after
CD playback is over
(AUTO STANDBY
function)
To cancel this function, press and hold again.
• If no operation is done for about 3 minutes
after CD playback stops, the System turns off.
Press briefly and repeatedly to specify the time
(in minutes) as follows:
Turn off the System
by using the sleep
timer
10
20
30
60
90
120
150
Canceled
• To check the time remaining until the shut-off time after
setting the sleep timer, press SLEEP once.
6
Playing Back Discs
This System can play back the following discs—regular CD and CD-R/CD-RW (recorded either in the audio CD or MP3
format).
• When playing back the MP3 track, MP3 indicator appears on the display.
To Set a Disc
1
2
3
On the System
On the System
The disc cover on
the System opens.
Place a disc correctly with its label side up,
then press down on the portions around
the disc’s center hole until you hear a click.
The disc cover on
the System closes.
• Do not close
forcibly the disc
cover with the
hand.
• When removing the disc, take out the disc
by holding it at the edge with pressing the
System’s pivot lightly.
Basic Disc Operations
Press
To
On the
System
On the
remote
Current track number and elapsed playing time appear on the
main display.
Playback the disc
• During playback, press again to stop playing for a moment.
• While playback is stopped, total track number and total playing
time (for MP3 disc, group number and track number) appear on
the main display.
Stop playback
Select a track
Increases the track numbers.
Decreases the track numbers.
—
Increases the group numbers while playback is stopped.
Decreases the group numbers while playback is stopped.
Select a group (MP3
only)
—
Fast-forwards the track by pressing briefly.
To stop searching, press 6.
—
Forward search /
Reverse search
Fast-reverses the track by pressing briefly.
—
To stop searching, press 6.
NOTES
• If the disc cannot be read correctly (because it is scratched, for example) or an unreadable CD-R or CD-RW is loaded,
playback will not start.
• If no disc is inserted, “NO DISC”appears on the main display.
7
Playing at Random—Random Play
Programming the Playing Order—
Program Play (except for MP3)
Press until the RND (random) indicator
appears on the display before you start
playback.
1
2
Press repeatedly until the PRGM
(program) indicator appears on the
display before you start playback.
1
2
3
Playback starts in random order.
Random Play ends when all tracks are
played.
or
Select the track number to program.
Press to program the selected track.
Operations on the Random Play Mode
To
Press
Repeat step 2 and 3 to program other tracks you
want.
To skip a track
• 4 does not work.
4
5
• If you try to program a 33rd track, “FULL”will
appear on the display.
Press once while
playback is stopped
to exit from the
random play.
To exit from
random play
The tracks are played in the order you
have programmed.
Operations on the Program Play Mode
Playing Repeatedly—Repeat Play
To
Press
Press repeatedly before you start
playback to specify the repeat mode as
follows:
Check the
programmed
contents
Press while playback
is stopped.
or
REP 1
REP OFF
REP 1
REP GRP
(MP3 only)
To erase the
last step
REP ALL
To erase
the entire
program
Press while playback
is stopped.
Repeats the current (or
specified) track.
1
2
Repeats all tracks in the
REP GRP current group. (MP3
Press twice while
playback is stopped
to exit from the
program play.
only)
To exit from
program play
REP ALL Repeats all tracks.
REP OFF
Normal playback
• The stored program
is erased.
8
Listening to the Radio
Basic Tuner Operations
Press
To
On the System On the remote
Each time you press the button, the band
changes as follows:
DAB
AM
FM
The selected band and frequency appear on
the main display.
• When an FM stereo broadcast with
sufficient signal strength is tuned in, the ST
(stereo) indicator lights on the display.
Select a band
When you change the source to DAB for the first time after plugging in the
AC power cord, the System automatically scans the DAB bands for available
ensembles. (See page10.)
• For general information of DAB, see“What is DAB system?”on page 10.
Press to improve reception.
The MONO indicator lights up on the display.
Reception will improve though the stereo
effect is lost.
Change the FM reception mode
(When a stereo broadcast is
hard to receive or noisy)
—
To restore the stereo effect, press again.
For FM/AM
Press and hold for more than 2 seconds.
The System starts searching for stations and
stops when a station of sufficient signal
strength is tuned in.
Select a frequency
or
or
or
• Press during searching to stop.
• Press repeatedly to change the frequency
step by step.
Press to select a preset number for the preset
station.
Tune in to a preset station
For DAB
—
• For presetting stations, see page 12.
Press and hold for more than 2 seconds.
• You can select from the ensembles
scanned by the ensemble scanning.
Select an ensemble
or
or
or
Select a service (either primary
or secondary)
Press briefly while tuning in to an ensemble.
Press briefly to select a preset number for the
preset service.
• For presetting services, see page 12.
Tune in to a preset service
Press and hold for more than 2 seconds.
The frequency changes every second
through all ensembles regardless of the
signal status.
—
Tune in to all ensembles
• Press and hold the button until the desired
ensemble is reached.
9
What is DAB system?
DAB (Digital Audio Broadcasting) is one of the digital radio broadcasting systems available today. It can deliver digital
quality sound without any annoying interference or signal distortion. Furthermore, it can carry text, pictures and data.
In contrast to FM broadcast, where each program is transmitted on its own frequency, DAB combines several programs
(called“services”) to form one“ensemble.”“Primary services”(main radio stations) are sometimes accompanied by
“secondary services”to broadcast additional programs.
CAUTION:
Electrostatic discharge from your body may cause noise from the speakers and you cannot hear the broadcast.
If this happens, turn off the System (on standby), then turn it on again.
Changing the DAB Information
Improving the DAB reception
With the supplied DAB antenna, you may not be able to
receive L-Band ensembles depending on your reception
condition. You can improve the reception of both L-Band
and Band III ensembles by connecting an active antenna
(see page 3) and supplying electricity to the antenna.
Each time you press the button, the main
display changes as follows:
Service Label
Ensemble ID
Frequency
While the System is on standby (Display
ON)
After connecting an active antenna, press
and hold for more than 2 seconds. The active
antenna is powered on and“ANT.P ON”
appears on the display.
Clock
(Non-DAB signal)
PTY
DLS
To power off the active antenna, press and
hold the button again. Then“ANT.P OFF”
appears on the display .
Preset Channel
Number
Scanning ensembles
With the ensemble scanning function, the System scans
the DAB bands to pick out available ensembles under
your receiving condition.
PTY: Program Type (See page11.)
DLS: Dynamic Label Segment (text
messages the station sends)
• When you change the source to DAB for the first time
after plugging in the AC power code, the System
automatically performs the scanning.
NOTE
If no signals are sent, “NOSIGNAL”(instead of Service
Label), “NONE”(instead of PTY) or“NO TEXT”(instead of
DLS) appears on the display.
• When you moved your System or adjusted the antenna
position, perform the scanning manually.
Press and hold for more than 2 seconds
while tuning in to DAB.
When the scanning is complete, the System starts playing
the first service of the ensemble found first .
10
Receiving FM Stations with Radio Data System
Radio Data System allows FM stations to send an additional signal along with their regular program signals.
With the System, you can receive the following types of Radio Data System signals.
PS (Program Service):
PTY (Program Type):
RT (Radio Text):
Shows commonly known station names.
Shows types of broadcast programs.
Shows text messages the station sends.
Enhanced Other Networks: Provides the information about the types of the programs broadcast by the Radio Data
System stations of the different networks.
NOTE
If you want to know more about Radio Data System, visit <http://www.rds.org.uk>.
Changing the Radio Data System
Information
Searching for Programs by PTY
Codes (PTY Search)
While listening to an FM station:
Each time you press the button, the main
display changes as follows:
You can locate a particular kind of program from the 30
preset stations (see page 12) by specifying PTY codes.
While listening to a DAB service:
You can locate a particular kind of program from among
all the services you can receive by specifying PTY codes.
PS
PTY
Frequency
(Non-Radio Data System signal)
RT
For details about PTY codes, see page 19.
Press to enter the PTY code setting
mode.
NOTE
If no Radio Data System signals are sent by a station,
“NO PS,”“NO PTY,”or“NO RT”appears on the main display.
1
“PTY”and“SELECT”appear on the
main display.
Select a PTY code.
or
2
The System starts searching, stops
when it finds the program of
the selected PTY code (“FOUND”
appears on the display), and tunes
in to it.
3
NOTES
• To stop searching any time during search for FM stations,
press PTY SEARCH.
• To stop searching any time during search for DAB
services, press CANCEL or PTY SEARCH.
• To continue searching after it stops on an unwanted
program/service, press PTY SEARCH again while the PTY
code is flashing on the display.
• If no program/service is found, “NOTFOUND”appears on
the display.
11
Switching Temporarily to
a Program of Your Choice
Automatically
Presetting Stations and Services
You can preset 30 FM stations, 15 AM stations and 30 DAB
services manually.
Tune in to a station/service you want to preset.
The Enhanced Other Networks function allows the System
to switch temporarily to a preset FM station broadcasting
a program of your choice (TA, NEWS, or INFO).
• This function works while listening to an FM program
providing the required signals.
• You can also store the monaural reception mode
for FM preset station if selected.
1
Press to activate the preset number
entry mode.
Press repeatedly to select the program type
as follows:
• Finish the following process while
the indication on the display is
flashing.
2
TA
NEWS
INFO
OFF
Press to select a preset number for
the station/service you store.
or
3
TA
NEWS News
Program the purpose of which is
impart advice in the widest sense.
Traffic announcement in your area
Press to store the station/service.
INFO
4
NOTES
How the Enhanced Other Networks function actually
works:
• If you store a new station/service into an occupied
preset number, the previously stored one in that
number will be erased.
• When you preset DAB services, you can only preset
primary services. If you select a secondary service to
store, its primary service is stored instead.
• When you unplug the AC power cord or if a power
failure occurs, the preset stations/services will be erased
in two days.
When a station starts broadcasting the program of
your choice, the System automatically switches to the
station. The PTY code indicator starts flashing.
After the program is over, the System goes back to the
previously tuned station, but the function still remains
active (the indicator stops flashing and remains lit).
12
Connecting a Portable Audio Device
This System has LINE IN/OUT jacks to connect a portable audio device.
Connect between the device and the System by using the stereo mini plug cord (not supplied).
IMPORTANT:
It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without the consent of
the owner of copyright in the sound or video recording, broadcast or cable programme and in any literary, dramatic,
musical, or artistic embodied therein.
Playing back a portable audio device
Portable audio device
(Digital Audio Player, etc.)
To audio output
(or headphone out, etc.)
To Play Back a Portable Audio Device
“LINE”appears on the main display.
1
2
Easily
By using QP Link (Quick Portable Link), you can easily start
Start playing the device connected.
playing back a portable audio device connected to the
LINE IN jack.
Adjust the volume level to the level
you want to listen to.
Press and hold for more than 2 seconds
to activate QP Link.
On the remote
3
QP Link indicator appears on the display.
To cancel this function, press and hold
for more than 2 seconds again.
To Adjust the Audio Input Level
If the sound from the device connected to the LINE IN
jack is too loud or too quiet, you can change the audio
input level through the LINE IN jack (without changing
the volume level).
When QP Link is activated, connecting a portable device
to the LINE IN jack and starting playback performs the
following:
• While listening to another source...
Press and hold for more than 2 seconds
while“LINE”is selected as a source.
Changes the source to“LINE”automatically. (If you
change from“LINE”to another source, QP Link will be
canceled.)
• While the System is on standby...
Turns on the System and changes the source to“LINE”
automatically (except when the Save mode is on).
On the remote
You can select one of three levels
alternately.
NOTE
See“Learning More about This System”on page 16.
13
NOTE
If an external device is not equipped with a stereo mini plug audio output, use a plug adaptor to convert the stereo mini
plug to the corresponding plug of the audio output.
Recording to a portable audio device
Portable audio device equipped with the audio input
To audio input
(Digital Audio Player, etc.)
Start recording or standby recording on the device.
1
2
Start playing the CD or tune into the station you want to
recording.
or
To Select the Audio Output Level
If the recorded sound on the device connected to the LINE OUT jack is too loud or
too quiet, you can change the audio output level through the LINE OUT jack (without
changing the volume level).
On the System
Press to change the audio output level.
You can select one of two levels alternately as follows:
OUT_LVL1
OUT_LVL2
14
Setting the Clock and Daily Timer
Setting the Clock
Without setting the built-in clock, you cannot use Daily Timer and Sleep Timer.
Press to activate the clock setting mode.
• If you have already adjusted the clock before, press the
button repeatedly until the clock setting mode is selected.
1
Adjust the hour, then the minute.
or
2
• To exit from the clock setting, press CLOCK/TIMER as required.
• To go back to the previous step, press CANCEL.
Setting the Daily Timer
Using Daily Timer, you can wake up with your favorite music.
• You can store three Daily Timer settings; however, you can activate only one of Daily Timers at the same time.
Press repeatedly to select one of the timer setting modes you want to set—DAILY 1 ON
time, DAILY 2 ON time, or DAILY 3 ON time—as follows:
Daily 1 Timer
Daily 2 Timer
DAILY 1
Canceled
ON (Time)
DAILY 2
ON (Time)
1
Clock setting
(See above.)
ON (Time)
DAILY 3
Daily 3 Timer
1Adjust the hour then the minute for on-time.
2Adjust the hour then the minute for off-time.
3Select the playback source—“DAB/FM/AM,”“CD,”or “LINE.”
4For “DAB/FM/AM”: Select a preset channel.
For “LINE”: Make the external device ready for playback.
5Select the volume level.
• You can select the volume level (“VOLUME 0”to“VOLUME 31”and“VOLUME – –”). If
you select“VOLUME – –,”the volume is set to the last level when the System is turned
off.
or
2
3
Turn off the System (on standby).
• To exit from the timer setting, press CLOCK/TIMER as required.
• To correct a misentry during the process, press CANCEL. You can return to the previous step.
To turn off the Daily Timer
Press repeatedly to select“DAILY 1,”“DAILY 2,”or“DAILY 3.”
1
2
To turn on the Daily Timer again, select one of the timer settings by pressing CLOCK/TIMER, then press SET.
15
Learning More about This System
Basic and Common Operations (see page 5)
• Sound adjustments also affect the sound through the
headphones.
• Sound adjustments do not affect recording to the
external device.
• You can set the clock and daily timer while the Save
mode is turned on. While setting the clock or daily timer,
the display is turning on.
Listening to the Radio (see page 9)
• The time shown on the display by changing the DAB
information is based on the built-in clock of the system,
not on the information sent through DAB.
• The Enhanced Other Networks function is available only
when tuning in to FM.
Connecting a Portable Audio Device (see page 13)
Playing back a portable audio device:
• If a component connected to the LINE IN jack is not loud
Playing Back Discs (see pages 7)
• This System cannot play“packet write”discs.
• For MP3 playback...
enough, QP Link may not work properly.
In such cases, adjust the volume level of the component
louder so that the System can detect the sound signal
properly.
– MP3 discs are required a longer readout time than
regular CDs. (It depends on the complexity of the
group/file configuration.)
– Some MP3 files cannot be played back and will be
skipped. This result from their recording processes and
conditions.
– When making MP3 discs, use ISO 9660 Level 1 or Level
2 for the disc format.
– This System can play back MP3 files with the extension
code <.mp3> (regardless of the letter case—upper/
lower).
• Changing from“LINE”to another source while QP Link
works will deactivate QP Link temporarily.
In this case, the following reactivates QP Link:
– Pressing QP LINK on the remote control
– When no sound signal comes from the LINE IN jack for
about 30 seconds after the System is turned off
• If you press
button to turn the System off or if preset
Timer turns the System off while QP Link works, the
System deactivates QP Link temporarily.
In such cases, the following reactivates QP Link:
– When no sound signal comes from the LINE IN jack for
about 30 seconds after the System is turned off
– When you turn on the power again
– It is recommended that you make each MP3 file at a
sampling rate of 44.1 kHz and at bit rate of 128 kbps.
This System cannot play back files made at bit rate of
less than 64 kbps.
– Playback order of MP3 tracks may be different from
the one you have intended while recording. If a folder
does not include MP3 tracks, they are ignored.
• This System can recognize up to 511 tracks in a disc.
Also, the System can recognize up to 150 tracks per
group and up to 99 groups in a disc. (for MP3)
– If there are any unplayable files in a folder, those files
are also counted in the total file number.
– Playable files which do not belong to any groups are
handled as Group 1.
Setting the Clock and Daily Timer (see page 15)
• “0:00”will flash on the display until you set the clock.
• The clock may gain or lose 1 to 2 minutes per month. If
this happens, readjust the clock.
• When you unplug the AC power cord or if a power
failure occurs, the clock and the timer will be canceled.
You need to set the clock first, then the timer again.
• When the on-time of the daily timer comes, the System
sets the volume level gradually to the preset level after
about 10 seconds.
MP3 groups/tracks configuration
This System plays back MP3 tracks as follows.
Timer Priority:
• If you set the Sleep Timer after Daily Timer starts playing
the selected source, Daily Timer is canceled.
Hierarchy
Level 1
Level 2
Level 3
Level 4
Level 5
Group with its play order
MP3 track with its play order
16
Troubleshooting
If you are having a problem with your System, check this list for a possible solution before calling for service.
General
Disc Operations
Power does not come on.
\ Power plug is not inserted securely. Plug in securely.
Adjustments or settings are suddenly canceled
before you finish.
\ There is a time limit. Repeat the procedure again.
The disc does not play.
\ The disc is placed upside down. Place the disc with
the label side up.
\ MP3 disc is recorded with the“packet writing (UDF
file).”It cannot be played. Check the files you want to
play back.
Operations are disabled.
ID3 Tag on an MP3 disc cannot be shown.
\ There are two types of ID3 Tag—Version 1 and Version
2. This System can only show ID3 Tag Version 1.
\ The built-in microprocessor may malfunction due to
external electrical interference. Unplug the AC power
cord and then plug it back in.
MP3 groups and tracks are not played back as you
expect.
Unable to operate the System from the remote
control.
\ The path between the remote control and the
remote sensor on the System is blocked.
\ The batteries are exhausted.
\ The playing order is determined when the disc was
recorded. It depends on the writing application.
The disc sound is discontinuous.
\ The disc is scratched or dirty.
The disc tray does not open or close.
\ The AC power cord is not plugged in.
No sound is heard.
\ Speaker connections are incorrect or loose.
\ Headphones are connected.
Timer Operations
Radio Operations
Daily Timer does not work.
Hard to listen to broadcasts because of noise.
\ Antennas connections are incorrect or loose.
\ The AM loop antenna is too close to the System.
\ The FM antenna is not properly extended and
positioned.
\ The System has been turned on when the on-time
comes. Timer starts working only when the System is
turned off.
Cannot receive an ensemble.
\ Your area is not covered by the ensemble.
\ The DAB antenna is not properly extended or
positioned. Adjust the antenna and try the ensemble
scanning again.
\ Connect an active antenna (not supplied).
17
Maintenance
To get the best performance of the System, keep your discs and mechanism clean.
Handling discs
Cleaning the System
• Remove the disc from its case by holding it at the edge
while pressing the center hole lightly.
• Do not touch the shiny surface of the disc, or bend the
disc.
• Stains should be wiped off with a soft cloth. If the
System is heavily stained, wipe it with a cloth soaked in
water-diluted neutral detergent and wrung well, then
wipe clean with a dry cloth.
• Put the disc back in its case after use.
• Be careful not to scratch the surface of the disc when
placing it back in its case.
• Avoid exposure to direct sunlight, temperature
extremes, and moisture.
• Since the System may deteriorate in quality, become
damaged or get its paint peeled off, be careful about
the following:
– DO NOT wipe it with a hard cloth.
– DO NOT wipe it strong.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such as
insecticides to it.
– DO NOT allow any rubber or plastic to remain in
contact for a long time.
To clean the disc:
Wipe the disc with a soft cloth in a straight line from
center to edge.
Specifications Specifications and appearance are subject to change without prior notice.
Amplifier section
Speakers
OUTPUT POWER:
Speaker units: 8 cm cone x 1
Impedance: 4
10 W (5 W + 5 W) at 4 (10% THD)
Speakers/Impedance: 4 – 16
Audio Input LINE IN:
Dimensions (approx.):
130 mm x 171 mm x 136 mm (W/H/D)
Mass (approx.): 0.75 kg each
500 mV/47 k (at“LINE IN LVL1”)
250 mV/47 k (at“LINE IN LVL2”)
125 mV/47 k (at“LINE IN LVL3”)
Audio Output LINE OUT:
Supplied Accessories
See page 2.
1.0 Vrms (47 k ) (at“LINE OUT LVL1”)
2.0 Vrms (47 k ) (at“LINE OUT LVL2”)
General
Power requirements: AC 230 V
, 50 Hz
Power consumption:
Tuner section
20.0 W (Power on), 2.5 W (Standby mode)
2.0 W or less (Save mode)
FM Tuning range: 87.50 MHz - 108.00 MHz
AM (MW) Tuning range: 522 kHz - 1 629 kHz
DAB tuning range:
Mass: 1.8 kg
Dimensions (W x H x D): 270 mm x 68.5 mm x 203 mm
BAND III: 174.928 MHz - 239.200 MHz
L-BAND: 1 452.960 MHz - 1 490.624 MHz
CD player section
Dynamic range: 88 dB
Signal-to-noise ratio: 93 dB
Wow and flutter: Immeasurable
18
Description of the PTY codes for Radio Data System and DAB
NEWS:
AFFAIRS:
News.
WEATHER: Weather reports and forecasts.
FINANCE: Stock Market reports, commerce, trading
etc.
Topical program expanding or enlarging
upon the news—debate, or analysis.
INFO:
Programs the purpose of which is to impart CHILDREN: Programs targeted at a young audience.
advice in the widest sense.
Programs concerned with any aspect of
sports.
Educational programs.
All radio plays and serials.
SOCIAL/FACTUAL*1:
Programs about sociology, history,
SPORT:
geography, psychology and society.
Religious programs.
PHONE IN: Involving members of the public
expressing their views either by phone or
at a public forum.
EDUCATE:
DRAMA:
RELIGION:
CULTURE/ARTS*1:
Programs concerning any aspect of
national or regional culture, including
language, theater, etc.
TRAVEL:
LEISURE:
JAZZ:
Travel information.
Programs about recreational activities.
Jazz music.
SCIENCE:
Programs about natural sciences and
technology.
COUNTRY: Songs which originate from, or continue
the musical tradition of the American
Southern States.
VARIED/TALK*1:
Used for mainly speech-based programs
such as quizzes, panel games and
personality interviews.
Commercial music of current popular
appeal.
NATION M: Current popular music of the nation or
region in that country’s language.
POP M:
OLDIES:
Music from the so-called“golden age”of
popular music.
ROCK M:
EASY M:
Rock music.
Current contemporary music considered to
be“easy-listening”.
FOLK M:
Music which has its roots in the musical
culture of a particular nation.
DOCUMENT: Programs concerning factual matters,
presented in an investigative style.
LIGHT M/CLASSICL*1:
Instrumental music, and vocal or choral
works.
TEST*2:
Broadcasts for testing emergency
broadcast equipment or unit.
Emergency announcement.
No program type, undefined program, or
difficult to categorize into particular types.
CLASSICS/CLASSICM*1:
ALARM*2:
NONE*2:
Performances of major orchestral works,
symphonies, chamber music, etc.
Music not fitting into any of the other
categories.
OTHER M:
1
2
*
The PTY codes are different between Radio Data System and DAB. The former is for Radio Data System, and the latter
is for DAB.
Only Radio Data System has this PTY code.
*
NOTE
Classification of the PTY codes for some FM stations may be different from the above list.
19
SAFETY INSTRUCTIONS
“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”
This equipment has been designed and manufactured to meet international safety standards but, like any
electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured.
Do read the operating instructions before you attempt to use the equipment.
Do ensure that all electrical connections (including the mains plug, extension leads and interconnections
between pieces of equipment) are properly made and in accordance with the manufacturer’s instructions. Switch
off and withdraw the mains plug when making or changing connections.
Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
Do be careful with glass panels or doors on equipment.
DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged
in any way—switch off, withdraw the mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose dangerous voltages.
DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for
unattended operation or has a standby mode.
Switch off using the switch on the equipment and make sure that your family know how to do this.
Special arrangements may need to be made for infirm or handicapped people.
DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of
traffic safety. It is illegal to watch television whilst driving.
DON’T listen to headphones at high volume as such use can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs with wood screws—to ensure complete safety always fit the
manufacturer’s approved stand or legs with the fixings provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL
– NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case
—this could result in a fatal electrical shock.;
– NEVER guess or take chances with electrical equipment of any kind—it is better to be safe than sorry!
20
EN
© 2006 Victor Company of Japan, Limited
0706KTCMDWJSC
|