CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/ Top/ Back: No obstructions should be placed in the areas shown by the dimensions below.
3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of
10 cm or more.
Basic and Common Operations
Mains (AC) Line Instruction
(not applicable for Europe, U.S.A., Canada,
Australia, Hong Kong and U.K.)
Operating on the System
Operating on the Remote Control
Using Headphones
Be sure to turn down the volume before connecting or wearing
the headphones.
• Connecting the headphones will deactivate the speakers.
To
Press
To
Press
Adjusting the voltage selector
Use a screwdriver to slide the voltage marker so that it is
set to the same voltage as where you are plugging in the
unit.
Turn on or off
(standby) the power
The STANDBY lamp on the System turns off/
on.
Turn on or off (standby) the
power
The STANDBY lamp on the System turns off/
on.
MICRO COMPONENT SYSTEM
Front view
15 cm
Side view
15 cm
Bottom of the unit
See “Playing Back Discs”on page 4.
15 cm
15 cm
UX-N1S
See “Playing Back Discs”on page 4.
1 cm
1 cm
—Consists of CA-UXN1S and SP-UXN1S
See “Listening to FM and AM Broadcasts”on
page 5.
15 cm
Select a source
See “Listening to FM and AM Broadcasts”on
page 5.
10 cm
Select a source*
See “Connecting a Portable Audio Device”on
page 6.
UX-N1W
SP-UXN1S/SP-UXN1W CA-UXN1S/CA-UXN1W SP-UXN1S/SP-UXN1W
CA-UXN1S/CA-UXN1W
See “Connecting a Portable Audio Device”on
page 6.
—Consists of CA-UXN1W and SP-UXN1W
About the cooling fan
You can adjust the volume level from level 0
(VOL MIN) to level 31 (VOL MAX).
A cooling fan is mounted on the rear panel of the unit to prevent abnormal temperature inside the unit, thus assuring
normal operation of the unit.
Adjust the volume
You can adjust the volume level from level 0
(VOL MIN) to level 31 (VOL MAX).
Adjust the volume
The model information is located on the bottom.
AC 110V
220-240V
Drop the volume in a
moment
To restore the volume, press again, or adjust
the volume level.
* You can operate the source select
buttons on the System only touch
lightly, because these buttons are
“touch sensor panel.”
If you touch any one of these
buttons, they lights in blue briefly.
AHB PRO indicator appears on the display.
Reinforce the bass
sound
INSTRUCTIONS
Precautions
Notes on the power cord
To cancel this function, press again.
GNT0065-018A[US/UB/A/UW/UJ]
0306MOCMDWJSC
Voltage marker
Press once to adjust the bass level or press
twice to adjust the treble level.
• When you are away on travel or otherwise for an extended period of time, remove the plug from the wall outlet. A small
amount of power (5.0 W) is always consumed while the power cord is connected to the wall outlet.
• When unplugging the System from the wall outlet, always pull the plug, not the power cord.
• Do not handle the power cord with wet hands.
• Disconnect the power cord before cleaning the System or moving the System.
• Do not alter, twist or pull the power cord, or put anything heavy on it, which may cause fire, electric shock, or other accidents.
• If the cord is damaged, consult a dealer and have the power cord replaced with a new one.
Adjust the tone (Bass/
Treble)
Then press VOLUME + to increase the level or
press VOLUME – to decrease it.
©2006 Victor Company of Japan, Limited
Caution for mains (AC) line
• You can adjust the bass and treble level from
–3 to +3.
BEFORE PLUGGING IN, check that your mains (AC) line
voltage corresponds with the position of the voltage
selector switch on the bottom of the unit and, if different,
set the voltage selector correctly to prevent
Point it at the remote sensor on
the front panel. (The operating
range is approx. 7 m.)
Warnings, Cautions and Others
Press when the System is turned on.
Changing the display
brightness
Avoid moisture, water, dust, and high temperatures
• Do not place the System in moist or dusty places.
• If water gets inside the System, turn off the power and remove the plug from the wall outlet, then consult your dealer. Using
the System in this state may cause a fire or electrical shock.
• Do not expose the System to direct sunlight or place it near a heating device.
any damage or risk of fire/electric shock.
Caution —
button!
To cancel this function, press again.
Disconnect the mains plug to shut the power off completely.
When installing the apparatus, ensure that the plug is easily
accessible.
CAUTION:
Press and hold for more than 2 seconds when
the System is on standby.
DO NOT plug in before setting the voltage selector and all
connection procedures are complete.
STANDBY lamp
To cancel this function, press and hold for
more than 2 seconds again.
The
button in any position does not disconnect the
Notes on installation
Set the Save mode
mains line. The power can be remote controlled.
• When the unit is on standby, the STANDBY lamp lights red.
• When the unit is turned on, the STANDBY lamp goes off.
• Select a place which is level, dry and neither too hot nor too cold between 5˚C and 35˚C.
• Do not install the System in a place subject to vibrations.
• Do not put heavy objects on the System.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user
serviceable parts inside the System; leave all servicing to
qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation
when open. Do not view directly with optical instruments.
NOTE
Display Information
• Setting the Save mode allows you to reduce
power consumption by turning the display
off while on standby.
DO NOT turn off (standby)
the System with the volume
set to an extremely high level;
Otherwise, the sudden blast
of sound can damage your
hearing, speakers and/or
headphones when you turn
on the System or start
playback.
To prevent malfunction or damage of the System
• Do not insert any metallic objects, such as wires, hairpins, coins, etc. into the System.
• Do not block the vents.
CAUTION
Disc play mode indicators (See page 4.)
Changing the display
information (Clock
and Source)
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
Press briefly (except for FM mode).
For setting the clock, see page 5.
Tuner mode indicators
(See page 5.)
Timer mode indicators
(See the right column and page 5.
)
To clean the cabinet
• Use a soft cloth. Follow the relevant instructions on the use of chemically-coated cloths.
• Do not use benzene, thinner or other organic solvents and disinfectants. These may cause deformation or discoloring.
Press and hold until A.STBY indicator appears
on the display.
Turn off the System
automatically after CD
playback is over
(AUTO STANDBY
function)
CAUTION:
• Do not block the ventilation openings or holes. (If the
ventilation openings or holes are blocked by a newspaper
or cloth, etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
• When discarding batteries, environmental problems
must be considered and local rules or laws governing the
disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping
or splashing and that no objects filled with liquids, such
as vases, shall be placed on the apparatus.
[European Union only]
To cancel this function, press and hold again.
There are no user-serviceable parts inside. If anything goes wrong, unplug the power cord and consult
your dealer.
• If no operation is done for about 3 minutes
after CD playback stops, the System turns off.
Press briefly and repeatedly to specify the time
(in minutes) as follows:
QP Link indicator
(See page 6.)
Main Display
Turn off the System by
using the sleep timer
10
20
30
60
90
120
150
Canceled
• To check the time remaining until the shut-off time after
setting the sleep timer, press SLEEP once.
AHB PRO and A.STBY indicator (See the right column.)
1
3
Getting Started
Playing Back Discs
NOTES
This System can play back the following discs—regular CD and CD-R/CD-RW (recorded either in the audio CD or MP3 format).
• When playing back the MP3 track, MP3 indicator appears on the display.
Supplied Accessories
After unpacking, check to be sure that you have all the
following items. The number in parentheses indicates the
quantity of each piece supplied.
Prepare the Remote Control
When you use the remote control
for the first time, pull out the
insulation sheet.
Programming the Playing Order—Program
Play (except for MP3)
• Store the battery in a place where children cannot reach. If a child accidentally swallows the
battery, consult a doctor immediately.
Insulation sheet
• Do not recharge, short, disassemble or heat the battery or dispose of it in a fire. Doing any of
these things may cause the battery to give off heat, crack, or start a fire.
• Do not leave the battery with other metallic materials. Doing this may cause the battery to
give off heat, crack, or start a fire.
• When throwing away or saving the battery, wrap it in tape and insulate; otherwise, the
battery may start to give off heat, crack, or start a fire.
• Do not poke the battery with tweezers or similar tools. Doing this may cause the battery to
give off heat, crack, or start a fire.
• Dispose of battery in the proper manner, according to federal, state, and local regulations.
To Set a Disc
Press repeatedly until the PRGM (program) indicator
appears on the display before you start playback.
1
2
3
4
• Remote control (x 1)
1
2
3
• Lithium coin battery CR2025 (x 1) (The battery has been
installed when shipped from the factory.)
• AM loop antenna (x 1)
• FM antenna (x 1)
• AC plug adapter (x 1) (except for Hong Kong and
Australia)
On the System
On the System
or
Select the track number to program.
Replacing the Battery in the Remote Control
Lithium coin battery
(product number: CR2025)
Insert the battery into the
remote control by matching the
polarity (+ and –) correctly.
Press to program the selected track.
Repeat step 2 and 3 to program other tracks you want.
Place a disc correctly with its label side up, then
press down on the portions around the disc’s
center hole until you hear a click.
The disc cover on the
System opens.
The disc cover on the
System closes.
CAUTION:
If anything is missing, consult your dealer immediately.
• If you try to program a 33rd track, “FULL”will appear on the
display.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
• Do not close forcibly
the disc cover with
the hand.
• When removing the disc, take out the disc
by holding it at the edge with pressing the
System’s pivot lightly.
The tracks are played in the order you have
programmed.
5
Connections
Do not connect the AC power cord until all other connections have been made.
Operations on the Program Play Mode
To
Press
NOTES
Basic Disc Operations
• Make sure the antenna conductors do not touch any other terminals,
connecting cords and power cord. Also, keep the antennas away from
metallic parts of the System, connecting cords, and the AC power cord.
This could cause poor reception.
• If the cords are covered with vinyl, remove the vinyl to expose the tip
of the cord by twisting the vinyl.
AM loop antenna
(supplied)
Turn it until the best
reception is obtained.
Press
To assemble the AM loop antenna
Check the
programmed
contents
or
To
Press while playback is stopped.
On the
System
On the
remote
FM antenna (supplied)
Current track number and elapsed playing
time appear on the main display.
Extend it so that you can obtain the best reception.
To erase the
last step
Playback the disc
• During playback, press again to stop
playing for a moment.
To erase
the entire
program
To connect the AM loop antenna
Press while playback is stopped.
• While playback is stopped, total track
number and total playing time (for MP3
disc, group number and track number)
appear on the main display.
Hold
2
1
Stop playback
Select a track
Press twice while playback is
stopped to exit from the program
play.
For better FM/AM reception
Outdoor FM antenna
(not supplied)
To exit from
program play
Release
3
Insert
• The stored program is erased.
Disconnect the supplied FM antenna,
and connect to an outdoor FM antenna
using a 75 Ω wire with coaxial type
connector.
Increases the track numbers.
Decreases the track numbers.
Playing at Random—Random Play
PHONES
SPEAKERS
RIGHT
LEFT
COAXIAL
Playing Repeatedly—Repeat Play
Press until the RND (random) indicator appears on
the display before you start playback.
ANTENNA
LOOP
1
2
Press repeatedly before you start playback to specify
the repeat mode as follows:
AM EXT
Increases the group numbers while playback
is stopped.
—
—
IMPEDANCE
MIN
Playback starts in random order.
Select a group (MP3
only)
Vynile-covered wire (not supplied)
AM loop antenna
Keep it connected.
REP 1
REP GRP
Random Play ends when all tracks are played.
Extend it horizontally.
Decreases the group numbers while playback
is stopped.
(MP3 only)
REP OFF
REP ALL
Operations on the Random Play Mode
Fast-forwards the track by pressing briefly.
—
—
To connect the speaker cords
Repeats the current (or specified)
track.
NOTES
To
Press
1
2
6
To stop searching, press
.
REP 1
Forward search /
Reverse search
• DO NOT connect more than one speaker
to each terminal.
• DO NOT allow the conductor of the
speaker cords to be in touch with the
metallic parts of the System.
Make sure the both speakers are connected
correctly and firmly.
Fast-reverses the track by pressing briefly.
Repeats all tracks in the current
group. (MP3 only)
To a wall outlet
4
To skip a track
•
does not work.
REP GRP
6
To stop searching, press
.
When connecting the speaker cords, match the
polarity of the speaker terminals: white cord to (+)
and white cord with black stripe to (–).
Plug the AC power cord only after
all connections are complete.
• If the wall outlet does not match
the AC plug, use the supplied AC
plug adapter. (except for Hong
Kong and Australia)
REP ALL Repeats all tracks.
REP OFF Normal playback
NOTES
Press once while playback is
stopped to exit from the random
play.
To exit from
random play
• If the disc cannot be read correctly (because it is scratched, for example) or an unreadable CD-R or
CD-RW is loaded, playback will not start.
• If no disc is inserted, “NO DISC” appears on the main display.
Release
3
Hold
1
Insert
2
2
4
|