7" Portable On-camera LCD Monitor
User Manual
Model:
HDSDI&HDMI, Waveform, Audio meter, Focus assist
DT-X71F
DT-X71H
DT-X71C
HDSDI&HDMI
HDMI
Please read this User Manual
throughout before using.
Maintenance
Monitor
1. Please keep the signal terminals and the cooling vent away from knife-edge, metal or liquid in order to
avoid short-circuit and damage.
2. Please don't try to disassemble any parts of the monitor by yourself, which would probably damage the
monitor and do harm to human body, and it will cause the invalidation of product warranty.
3. Please don't touch the screen with your fingers, which would probably deface the screen.
4. Please don't press the screen; the LCD is extremely exquisite and flimsy.
The power
Please use the provided power adapter or the battery recommended by the manufacturer in order to avoid
damage.
Please never use the light connector (2-pin, female) in right front of camera handle to power the
monitor; otherwise it will damage the circuit of the monitor.
Please disconnect the power cable or take off the battery under the following situations:
1. If you do not operate this monitor for a period of time;
2. If the power cable or power adaptor is damaged;
3. If you operate this monitor by the methods different from this User Manual, and cause unknown problems;
4. If the monitor housing is broken.
Working Environment
1. Please don't lay this product on the unstable place.
2. Please don't lay this product in hot, cold or wet location.
Cleaning
1. Please clean the screen with dry and downy cloth or special LCD cleanser.
2. Please do not press hard when cleaning the screen.
3. Please do not use water or other chemical cleanser to clean the screen. The chemical may damage the
LCD.
4. For first time use, please tear off the factory LCD film. To protect the LCD screen, please post the LCD
protection film offered in the package.
1. Features
DT-X71F
◆ New high resolution 7” LCD Panel
16:9, 1024×600, 16.77 million colors, 900:1
contrast, and H160°/ V160°viewing angle.
◆ Multiple inputs
◆ Peaking focus assist (red/blue switch)
The Peaking focus assist function is to mark the
sharpest edges of the image with red or blue color,
for users to check if the subjects are focused.
◆ Zebra stripes
2 HD/SD-SDI, 1 HDMI and 1 Composite input.
◆ Loop through outputs
Zebra Stripes are used to check if the image is
over exposed or not by showing black and white
lines on the monitor. It is considered over exposed
when luminance value exceeds 90%.
Each of the 2 input HD/SD-SDI has loop through
output.
◆ HDMI converted to SDI output
Supported HDMI formats: 480i / 576i / 720p (50,
59.94, 60) / 1080i (50, 59.94, 60) / 1080P (23.98
24, 25, 29.97, 30), and the output SDI will embed
the audio (48KHz) from HDMI.
◆ False color
The false color is used to aid in the setting of
camera exposure. Under false color mode, there’s
a false color key on the bottom of screen for
reference. The over exposed subjects (above 101
IRE) on the monitor will display as RED, and the
underexposed subjects will display as BLUE. For
correct exposed subjects, it will display as green
and pink.
◆ Waveform (Y, Cb, Cr, R, G, B) and full scale
There are totally 6 kinds of waveform display,
available under both SDI and HDMI, to check the
Luminance (Y), Blue-difference (Cb),
Red-difference (Cr), Red (R), Green (G), Blue (B),
and the Y, Cb, Cr can be simultaneously displayed, ◆ Blue Only
R, G, B can be simultaneously displayed, and
each of the waveforms can be set to full scale
display.
Under the Blue Only Mode, only the blue pixels
saturation can be adjusted quicker and more
accurately.
◆ Vector scope
The displayed vector scope pattern is available
under both SDI and HDMI, represents saturation
as distance from the center of the circle, and hue
as the angle, in standard position, around it.
◆ Histogram (R, G, B)
◆ DSLR scale zoom in
The Canon DSLR outputs the CMOS sensor ratio
HDMI and this zoom in mode can make the
effective image scale full screen on the monitor.
◆ G-sensor auto flip
The histogram is a bar graph that shows the
distribution of luminance values in the picture.
There’re R, G, B histograms that individually
displayed simultaneously, available under both
SDI and HDMI.
Enable the G-sensor auto flip, the image will
rotate automatically when monitor is bottom up.
◆ User definable function keys
There are 3 function keys on the monitor front
panel, and users could define the functions to the
keys to achieve shortcut.
◆ 16-ch audio meter
Under HDSDI, it displays 16 channels audio bars,
with mark, and under SDSDI or HDMI, it displays
2 channels audio bars with mark. The audio bar is
green, and will turn yellow when audio exceeds
-20dB, and turn red when exceeds -10dB.
◆ SDI timecode
◆ User editable video title
User can edit a video title for the current camera,
and the title will display on the top of screen.
◆ Front and Rear 3-color TALLY light
2 TALLY lights design, to give “live” signals to
people in front of the camera, as well as the
camera operator behind.
Under SDI input, it can display the SMPTE
timecode, which is used extensively for
synchronization, and for logging and identifying
material in recorded media.
DT-X71H
◆ New high resolution 7” LCD Panel
16:9, 1024×600, 16.77 million colors, 900:1
contrast, and H160°/ V160°viewing angle.
◆ Multiple inputs
◆ User definable function keys
There are 2 function keys on the monitor front
panel, that permit users to define shortcuts for the
various functions.
2 HD/SD-SDI, 1 HDMI, 1 Composite input
and L/R stereo audio.
◆ User editable video title
◆ Loop through outputs
User can edit a video title for the current camera,
and the title will display on the top of screen.
◆ Front and Rear 3-color TALLY light
2 TALLY lights design, to give “live” signals to
people in front of the camera, as well as the
camera operator behind.
1 HD/SD-SDI loop through output.
◆ DSLR scale zoom in
The Canon DSLR outputs the CMOS sensor ratio
HDMI and this zoom in mode can make the
effective image scale full screen on the monitor.
◆ Image Flip
Set image to rotate by 180°.
DT-X71C
◆ New high resolution 7” LCD Panel
16:9, 1024×600, 16.77 million colors, 900:1
contrast, and H160°/ V160°viewing angle.
◆ Multiple inputs
◆ User definable function keys
There are 2 function keys on the monitor front
panel, and users could define the functions to the
keys to achieve shortcut.
1 HDMI, 1 Composite input
and L/R stereo audio input.
◆ User editable video title
◆ Loop through outputs
User can edit a video title for the current camera,
and the title will display on the top of screen.
◆ Front and Rear 3-color TALLY light
2 TALLY lights design, to give “live” signals to
people in front of the camera, as well as the
camera operator behind.
1 Composite loop through output.
◆ DSLR scale zoom in
The Canon DSLR outputs the CMOS sensor ratio
HDMI and this zoom in mode can make the
effective image scale full screen on the monitor.
◆ Image Flip
Set image to rotate by 180°.
2. Panel Instruction
DT-X71F
Front view
⑴ PHONE: Earphone jack
⑵ POWER: Power on/off
Connect with power cable or mount battery, press the “POWER” and the power indicator is turned on
and after 10 seconds, the monitor will be switched on and get into normal working status. Press the
“POWER” again, the indicator is turned off and monitor is switched off.
Disconnect with power cable or take off the battery if the monitor will not be used for a period of time.
⑶ IN: Input signal selection
Press “IN” and revolve the “OK” to select the input video signal.
⑷ F1: User definable function key 1
⑸ FOCUS: Peaking Focus Assist
Press “FOCUS” once, it will display the current peaking on/off status. Press “FOCUS” again to switch
on RED line focus assist, switch on BLUE line focus assist, and switch off in turn.
⑹ F.COLOR: False color
Press “F.COLOR” once, it will display the current false color on/off status. Press “F.COLOR” again to
switch on/off the false color mode.
⑺ DISPLAY: Display current settings
Press “Display” to display safety mark, title and the current input signal information
⑻ F2: User definable function key 2
⑼ F3: User definable function key 3
⑽ WAVEFORM: Display waveform
Press “WAVEFORM” once, it will display the waveform menu as:
Revolve “OK” to select a waveform display mode and turn it on.
The selected waveform will display on the screen.
⑾ VECTOR: Display vector scope
Press “VECTOR” to switched on/off the Vector scope
⑿ MENU: Press to enter Menu
⒀ OK: Select and Apply
Under menu system, revolve “OK” to adjust settings and press to apply; and out of menu system,
directly revolve “OK” to adjust volume.
⒁ TALLY Light: Red, Green and Yellow 3-color TALLY indicator
Rear view
⑴ DC 12V IN: Connect with DC12V 4-pin XLR power adapter.
⑵ TALLY Light: Red, Green and Yellow 3-color TALLY indicator
⑶ Battery mount:
Connect with JVC battery BN-VF823 or SWIT battery BN-S8823 to power the monitor.
⑷ HDSDI IN1/2: HD/SD-SDI input (BNC connector)
⑸ HDSDI OUT: HD/SD-SDI loop through output (BNC connector)
⑹ HDSDI LOOP1/2: HD/SD-SDI loop through output (BNC connector)
⑺ VIDEO IN: Composite video input (BNC connector)
⑻ TALLY controlling port (RJ45)
⑼ HDMI: HDMI input
Input formats
Input
Supported formats
CVBS
PAL / NTSC
480I / 576I / 480P / 576P
1080i (60 / 59.94 / 50)
720p (60 / 59.94 / 50)
1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98)
1080i (60 / 59.94 / 50)
1080p (30 / 29.97 / 25 / 24 / 23.98)
720p (60 / 59.94 / 50)
480i (59.94)
HDMI
SDI
SMPTE-274M
SMPTE-296M
SMPTE-125M
ITU-R BT.656
576i (50)
DT-X71H
Front view
⑴ PHONE: Earphone jack
⑵ POWER: Power on/off
Connect with power cable or mount battery, press the “POWER” and the power indicator is turned on and
after 10 seconds, the monitor will be switched on and get into normal working status. Press the “POWER”
again, the indicator is turned off and monitor is switched off.
Remark: Disconnect with power cable or take off the battery if the monitor will not be used for a period of time.
⑶ VIDEO: Press to switch the input signal to Composite video
⑷ HDMI: Press to switch the input signal to HDMI
⑸ HD-SDI1: Press to switch the input signal to the first HD-SDI channel
⑹ HD-SDI2: Press to switch the input signal to the second HD-SDI channel
⑺ MENU: Press to enter Menu
⑻ F1: User definable function key 1
⑼ F2: User definable function key 2
⑽ RATIO: 16:9 and 4:3 switch
⑾ ZOOM: Picture Zoom-in
Press “ZOOM” to switch ZOOM1: Canon DSLR scale zoom-in, and ZOOM2: pixel to pixel zoom-in.
⑿ DISPLAY: Display current settings
Press “Display” to display safety mark, title and the current input signal information
⒀ OK: Select and Apply
Under menu system, revolve “OK” to adjust settings and press to apply; and out of menu system,
directly revolve “OK” to adjust volume.
⒁ TALLY Light: Red, Green and Yellow 3-color TALLY indicator
Rear view
⑴ DC 12V IN: Connect with DC12V 4-pin XLR power adapter.
⑵ TALLY Light: Red, Green and Yellow 3-color TALLY indicator
⑶ Battery mount:
Connect with JVC battery BN-VF823 or SWIT battery BN-S8823 to power the monitor.
⑷ HDSDI IN1/2: HD/SD-SDI input (BNC connector)
⑸ HDSDI OUT: HD/SD-SDI loop through output (BNC connector)
⑹ VIDEO IN: Composite video input (BNC connector)
⑺ AUDIO L/R: Stereo audio L/R input (RCA connector)
⑻ TALLY controlling port
⑼ HDMI: HDMI input
Input formats
Input
Supported formats
CVBS
PAL / NTSC
480I / 576I / 480P / 576P
1080i (60 / 59.94 / 50)
720p (60 / 59.94 / 50)
1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98)
1080i (60 / 59.94 / 50)
1080p (30 / 29.97 / 25 / 24 / 23.98)
720p (60 / 59.94 / 50)
480i (59.94)
HDMI
SDI
SMPTE-274M
SMPTE-296M
SMPTE-125M
ITU-R BT.656
576i (50)
DT-X71C
Front view
⑴ PHONE: Earphone jack
⑵ POWER: Power on/off
Connect with power cable or mount battery, press the “POWER” and the power indicator is turned on
and after 10 seconds, the monitor will be switched on and get into normal working status. Press the
“POWER” again, the indicator is turned off and monitor is switched off.
Remark: Disconnect with power cable or take off the battery if the monitor will not be used for a period of
time.
⑶ VIDEO: Press to switch the input signal to Composite video
⑷ HDMI: Press to switch the input signal to HDMI
⑸ B/W: Black and White mode
⑹ OVERSCAN: Overscan / Underscan switch
⑺ MENU: Press to enter Menu
⑻ F1: User definable function key 1
⑼ F2: User definable function key 2
⑽ RATIO: 16:9 and 4:3 switch
⑾ ZOOM: Picture Zoom-in
Press “ZOOM” to switch ZOOM1: Canon DSLR scale zoom-in, and ZOOM2: pixel to pixel zoom-in.
⑿ DISPLAY: Display current settings
Press “Display” to display safety mark, title and the current input signal information
⒀ OK: Select and Apply
Under menu system, revolve “OK” to adjust settings and press to apply; and out of menu system, directly
revolve “OK” to adjust volume.
⒁ TALLY Light: Red, Green and Yellow 3-color TALLY indicator
Rear view
⑴ DC 12V IN: Connect with DC12V 4-pin XLR power adapter.
⑵ Battery mount:
Connect with JVC battery BN-VF823 or SWIT battery BN-S8823 to power the monitor.
⑶ VIDEO OUT: Composite video loop through output (BNC connector)
⑷ AUDIO L/R: Stereo audio L/R input (RCA connector)
⑸ VIDEO IN: Composite video input (BNC connector)
⑹ HDMI: HDMI input
⑺ TALLY controlling port
⑻ TALLY Light: Red, Green and Yellow 3-color TALLY indicator
Input formats
Input
Supported formats
CVBS
PAL / NTSC
480I / 576I / 480P / 576P
1080i (60 / 59.94 / 50)
HDMI
720p (60 / 59.94 / 50)
1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98)
3. Menu Operation
Press “MENU” and it will display menu system
Revolve “OK” to select an item. The selected item will be highlighted display.
Press “OK” to enter the selected item.
Under menu system, press “MENU” to back to previous menu.
The menu will automatically save and quit if it remains idle.
4. Picture Settings Submenu
The Picture Settings Submenu includes:
⑴ CONTRAST: 0-100 value adjustment
⑵ BRIGHTNESS: 0-100 value adjustment
⑶ HUE: 0-100 value adjustment
(Only available under Composite input)
⑷ SATURATION: 0-100 value adjustment
⑸ SHARPNESS: 0-100 value adjustment
⑹ PIC.MODE: User defined and preset picture
modes: standard, soft and vivid selection
5. System Configuration Submenu
The System Configuration Submenu includes:
⑴ RATIO: Select “16:9” or “4:3” to adjust the aspect ratio.
⑵ SCAN: “UNDERSCAN” / “OVERSCAN” selection
⑶ ZOOM: “OFF”, “ZOOM1” and “ZOOM2” selection
ZOOM1: Canon DSLR scale zoom-in
ZOOM2: Pixel to Pixel zoom-in
⑷ MARKER: Select and set the safety mark
scale from 80%, 85%, 90% and 95%.
⑸ FLIP: Select “YES” to enable G-sensor auto
flip.
⑹ RESET: Revolve “OK” to RESET and press to
recover all to factory setting.
6. OSD Settings Submenu
The OSD Settings Submenu includes:
⑴ LANGUAGE: Menu language English / Chinese selection
⑵ H-POSITION: Menu horizontal position (0-100) adjustment, real-time preview, default value: 50, center.
⑶ V-POSITION: Menu vertical position (0-100) adjustment, real-time preview, default value: 50, center.
⑷ DURATION: Menu timeout setting
Set a time (in seconds) in which the menu
will automatically quit if remains idle.
Default: 10 seconds; Range: 5 seconds to
60 seconds.
7. Title Settings Submenu
Revolve "OK" button to select the letters, and press "OK" to input. Select SPACE to input space and DEL to
delete the left letter. Max 10 letters are supported.
After setting, press "MENU", the system will
save data to current user and quit menu. The
menu will automatically save and quit if it
remains idle.
8. Display Settings Submenu
The DISPLAY settings submenu is to select the
items to be displayed on screen when
‘DISPLAY” button is pressed. Revolve "OK" to
turn on/off the items:
(1) INFO: Including Input format, aspect ratio,
underscan/overscan, zoom status
(2) MARKER: Safety mark
(3) TITLE: User edited title
9. FUNCTION KEY Settings Submenu
The F KEY Settings Submenu is to define
Function Keys on the front keyboard.
The DT-X71F has 3 function keys:
F1, F2 and F3;
The DT-X71H and DT-X71C has 2 function
keys:
F1 and F2.
The available function items of each model are:
-------------------DT-X71F-------------------
01-RATIO: Aspect ratio switch
-------------------DT-X71H-------------------
01-RATIO: Aspect ratio switch
02-SCAN: Underscan / Overscan switch
03-ZOOM: Picture Zoom-in
02-SCAN: Underscan / Overscan switch
03-ZOOM: Picture Zoom-in
04-PIC. MODE: Preset picture mode switch
05-B/W: Color / Black & white switch
04-CLR.TEMP: Color-temperature switch
05-PIC MODE: Preset picture mode switch
06-B/W: Color / Black & white switch
07-REVERSE: Image flip
06-BLUE ONLY: Blue only mode switch on/off
07-ZEBRA: Zebra over exposure switch on/off
08-VECTOR: Vector scope switch on/off
09-PATTERN: Internal colorbar switch on/off
10-RGB HIST: R, G, B Histogram switch on/off
11-TIMECODE: SDI timecode display switch on/off
12-F.COLOR: False color mode switch on/off
13-AUDIO BAR: Audio meter display switch on/off
14-FOCUS: Peaking focus assist switch on/off, and
red/blue selection
-------------------DT-X71C-------------------
01-RATIO: Aspect ratio switch
02-SCAN: Underscan / Overscan switch
03-ZOOM: Picture Zoom-in
04-CLR.TEMP: Color-temperature switch
05-PIC MODE: Preset picture mode switch
06-B/W: Color / Black & white switch
07-REVERSE: Image flip
10. TALLY Light Operation
There are front and rear TALLY lights on the monitor, which can display RED, GREEN and YELLOW signals.
The TALLY light controlling port is the RJ45 socket at the rear panel, and terminal description is as follows:
Terminal
1
2
3
4
5
6
7
8
Description
Y
G
GND
R
The RED light is on when connecting the terminal “R” with “GND”, and goes out when disconnecting.
The GREEN light is on when connecting the terminal “G” with “GND”, and goes out when disconnecting.
The YELLOW light is on when connecting the terminal “Y” with “GND”, and goes out when disconnecting
11. Specifications
LCD Performance
Size
7.0 inches
Resolution
Aspect ratio
Color system
Brightness
Contrast
1024×RGB×600
16:9/4:3
NTSC/PAL
400cd/m2
900:1
Color
16.77 million colors
H/V:160/160
Viewing angle
Video Format
1080i (60 / 59.94 / 50)
SMPTE-274M
1080p (30 / 29.97 / 25 / 24 / 23.98)
720p (60 / 59.94 / 50)
SDI * SMPTE-296M
SMPTE-125M
480i (59.94)
ITU-R BT.656
576i (50)
480I / 576I / 480P / 576P
1080i (60 / 59.94 / 50)
HDMI
720p (60 / 59.94 / 50)
1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98)
General
Working voltage
DC12V, or Battery 6.5V-17V
DT-X71F
≤15W
≤8W
≤6W
Power consumption
DT-X71H
DT-X71C
Working temperature
Working humidity
Storage temperature
Storage humidity
Dimensions
0℃～+40℃
10%～90%
-15℃～+60℃
10%～90%
192×139×47mm
Net weight
550g
* DT-X71C doesn’t support SDI input.
12. Packing List
1. Monitor
×1
×1
×1
×1
×1
×1
×1
2. User Manual
3. Power adaptor
4. Power cable
5. Sun hood
6. Screw ball head
7. LCD protection film
This model is manufactured, warranted and supported by SWIT Electronics Co., Ltd. / SWIT Electronics USA, LLC,
and distributed in North America by JVC Professional Video Products.
To obtain service or for further information, please contact:
SWIT Electronics USA, LLC.
Address: 4300 Stevens Creek Blvd., Suite 230, San Jose, CA 95129
Toll free: 1 866 986-SWIT (7948) • Tel: 408 260-8258·Fax: 408 228-8438
|