COLOR VIDEO CAMERA
INSTRUCTIONS
TK-WD310
For Customer Use:
Enter below the Serial No. which is
located on the body. Retain this
information for future reference.
Model No. TK-WD310
Serial No.
LWT0127-001A
This instruction manual is made from 100% recycled paper.
8. Slots and openings in the cabinet and the back or bottom are
provided for ventilation, and to insure reliable operation of the
appliance and to protect it from overheating, these openings
must not be blocked or covered. The openings should never be
blocked by placing the appliance on a bed, sofa, rug, or other
similar surface.
This appliance should never be placed near or over a radiator
or heat register. This appliance should not be placed in a built-
in installation such as a bookcase unless proper ventilation is
provided.
9. This appliance should be operated only from the type of power
source indicated on the marking label. If you are not sure of the
type of power supplied to your home, consult your dealer or
local power company. For appliance designed to operate from
battery power, refer to the operating instructions.
10. For added protection for this product during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it form the wall outlet and disconnect the antenna
or cable system. This will prevent damage to the product due to
lightning and power-line surges.
11. Do not allow anything to rest on the power cord. Do not locate
this appliance where the cord will be abused by persons walk-
ing on it.
II
12. Follow all warnings and instructions marked on the appliance.
13. Do not overload wall outlets and extension cords as this can
result in fire or electric shock.
14. Never push objects of any kind into this appliance through cabi-
net slots as they may touch dangerous voltage points or short
out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the appliance.
15. Do not attempt to service this appliance yourself as opening or
removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
16. Unplug this appliance from the wall outlet and refer servicing
to qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the appliance.
c. If the appliance has been exposed to rain or water.
d. If the appliance does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as improper adjust-
ment of other controls may result in damage and will often
require extensive work by a qualified technician to restore
the appliance to normal operation.
e. If the appliance has been dropped or the cabinet has been
damaged.
f. When the appliance exhibits a distinct change in performance
- this indicates a need for service.
IIDI ownload from Www.Somanuals.com. All Manuals Search And Download.
17. When replacement parts are required, be sure the service tech-
nician has used replacement parts specified by the manufac-
turer that have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or
other hazards.
18. Upon completion of any service or repairs to this appliance,
ask the service technician to perform routine safety checks to
determine that the appliance is in safe operating
condition.
IV
Safety Precautions
FOR USA AND CANADA
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE.REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash wish arrowhead symbol, within an equi-
lateral triangle is intended to alert the user to the presence
of uninsulated "dangerous voltage" within the product's en-
closure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is in-
tended to alert the user to the presence of important oper-
ating and maintenance (servicing) instructions in the litera-
ture accompanying the appliance.
Information for USA
This device complies with part 15 of the FCC Rules. Changes or modifica-
tions not approved by JVC could void the user’s authority to operate the
equipment.
V
Due to design modifications, data given in this instruction book are sub-
ject to possible change without prior notice.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
AVERTISSEMENT:
POUR EVITER LES RISQUES D’INCENDIE OU
D’ELECTRO-CUTION, NE PAS EXPOSER
L’APPAREIL A L’HUMIDITE OU A LA PLUIE.
INFORMATION (FOR CANADA)
RENSEIGNEMENT (POUR CANADA)
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Class B est conforme á la norme NMB-003
du Canada.
VI
INTRODUCTION
Thank you for purchasing this product.
(These instrustions are for TK-WD310U and TK-WD310E.)
Before beginning to operate this unit, please read the instruction
manual carefully in order to make sure that the best possible perfor-
mance is obtained.
Features
Ⅵ Backlight compensation over a wide area is realized by the 14-bit Wide
Dynamic Range feature.
The Wide Dynamic Range feature controls the exposure time using a
maximum of 5 sampling timing for the image within a single screen.
Even when shooting in areas with large difference in lightning, subjects
with difference in brightness can be viewed in a clear and natural state.
Ⅵ 1/3-inch high-resolution DPS device adopted as shooting element to
realize high picture quality with no smearing or blooming in areas with
high luminance. In addition, 2.5lx (during F1.2, 50%, AGC SUPER set-
ting) is realized for minimum subject brightness.
Ⅵ Horizontal resolution of 480 lines (typ.) and vertical resolution of over
400 lines allow display of finely detailed video.
Ⅵ New device adopted for use even under strong electric field conditions.
Ⅵ Compatible with CS mount and VIDEO auto iris/DC auto iris.
* When using the C mount lens, C mount adapter is required.
Ⅵ Various settings in each menu screen are possible.
Menu settings can be performed easily using single button operations.
Ⅵ 3 white balance modes of ATW, AWB and MANUAL are available.
ATW mode that adjusts the white balance automatically according to
the changes in lighting conditions (color temperature) orAWB/MANUAL
mode that automatically or manually adjusts and locks the white bal-
ance of specific lighting conditions can be selected.
Ⅵ Camera title setting and display can be made.
Ⅵ Compact design allows installation in narrow spaces.
2
EASY INSTALLATION
The factory default settings are intended to give easy instal-
lation. Please attach a lens, a power supply, a video cable
and mount the camera securely. You should now have good
images.
The additional information contained in this handbook is intended
to give additional flexibility to more demanding installations.
Ⅲ Before starting an important recording, be sure to perform a
test recording in order to confirm that a normal recording is
possible.
Ⅲ We do not accept liability for the loss of a recording in the
case of it becoming impossible to record due to a problem
in the video camera, VCR or video tape.
Ⅲ We do not accept liability for any damage to the camera in
cases when it is dropped because of incomplete installation
due to not observing the installation instructions correctly.
Please be careful when installing the camera.
Characters and symbols used in this instruction manual.
CAUTION : Cautionary notes concerning operation of the
unit.
MEMO
: Reference such as restrictions of features, etc.
: Reference page or item.
੬
3
Contents
INTRODUCTION
Features ..................................................................................... 2
Contents..................................................................................... 4
Operating Precautions ............................................................... 5
Names and Operations of Parts ................................................. 8
CONNECTION/INSTALLATION
Basic System ........................................................................... 13
Mounting the lens..................................................................... 14
Connections on the back.......................................................... 16
Mounting the camera ............................................................... 18
Auto iris lens adjustment .......................................................... 20
Back focus adjustment ............................................................. 22
MENU SETTING
Menu settings ........................................................................... 24
Menu tree ................................................................................. 26
About menus ............................................................................27
FOCUS ADJUST screen .......................................................... 27
VIDEO ADJUST screen ........................................................... 28
WDR CUSTOM SETTINGS screen ...................................... 29
MANUAL WHITE BALANCE screen ..................................... 33
CAMERA SETTINGS screen ................................................... 34
LENS ADJUST screen .......................................................... 34
CAMERA TITLE EDIT screen ............................................... 36
FACTORY SETTINGS screen .................................................. 38
OTHERS
Troubleshooting ........................................................................ 39
Speifications............................................................................. 40
4
INTRODUCTION
Operating Precautions
● To save energy, when it is not being used turn the system’s
power off.
● This camera has been designed for indoor use.
When you use it outdoors, be sure to use an appropriate housing.
● Do not install or use the camera in the following places.
• In a place exposed to rain or moisture.
• In a place with vapor or oil soot, for example in a kitchen.
• When the ambient temperature rises above or falls below the
acceptable range (from –10°C to 50°C).
• Near a source of radiation, X-rays, strong radio waves or mag-
netism.
• In a place where corrosive gasses are generated.
• In a place subject to vibration.
• In a place with excessive dirt.
● If this camera and the cables connected to this camera are used
where there are strong electromagnetic waves or where there
is magnetism present, for example near a radio or TV transmit-
ter, power transformer or an electric motor, the picture may pro-
duce noise and the colours may be affected.
● This camera incorporates an AGC circuit. As a result, when it is
used under low light conditions, the camera sensitivity is auto-
matically boosted and the picture may look uneven. However,
this is not a malfunction.
● When this camera is used in the ATW mode, the recorded
colours may be slightly different from the actual colours due to
the operational principles of the auto-tracking white balance cir-
cuit. However, this is not a malfunction.
● Hunting may occur depending on the used lens. However, this
is not a malfunction of the unit.
● The screen surroundings may appear dark depending on the
used lens.
5
INTRODUCTION
Operating Precautions (continued)
● The white balance (ATW) of this device is optimally set for sun-
light. Proper white balance may not be achieved for artificial
lighting such as fluorescent lighting, etc.
● If you use this camera in locations where the camera is ex-
posed to fluorescent light, a slow color change may occur.
(White balance normal = 5,400 K, range is 2,500 K to 10,000 K.)
●
AGC SUPER: in this mode, ATW white balance may be inaccurate.
● White balance performance decreases under poor lighting con-
ditions.
● Observe the following when carrying out camera maintenance.
• Turn the power OFF before proceeding to carry out mainte-
nance.
If it is contaminated seriously, clean the contaminated part with
a cloth (or a tissue) which has been soaked in a solution of
water and a neutral detergent.
● The unit is to be powered by a DC 12 V or an AC 24 V power
supply.
The AC 24 V power supply should conform to the following:
U type : Class 2 only
E type : Isolated power supply only
● The beat may sometimes appear on the screen if gain is raised
when the line lock is in use, but the phenomenon takes place
due to the fluctuation of power frequency and is not a malfunc-
tion.
● At Low light levels, video iris lens may “Hunt”. Please adjust iris
level on lens to minimise hunting.
● Recommended range of operating temperature is 0°C to 35°C
degrees. The camera will function outside these parameters to
–10°C to 50°C degrees. But processing errors may be appar-
ent.
6
● Line-Lock is set for 50 Hz ±0.02 Hz. If line frequency is outside
this tolerance, picture may jitter and some interference may be
visible in high contrast scenes.
● Blemishes: Small spots are normal, the camera contains com-
pensation functions for blemishes above 120 mV (p-p) in value.
Please contact your JVC authorised dealer for further informa-
tion.
7
INTRODUCTION
Names and Operations of Parts
[Front and Bottom]
2
1
4
5
3
7
6
1 Lens mount
For use with CS mount lens.
(C-mount lenses require a conversion ring.)
2 Backfocus adjustment ring
Adjusting the back focus during lens installation.
Please refer to “Back focus adjustment” on ੬ Page 22 for in-
structions on how to adjust the back focus.
8
3 [BF LOCK] Back focus locking screw (× 2: 2 mm)
This serves to fix the back focus-adjusting ring.
4 Camera-mounting bracket
The bracket has been attached on the bottom of the camera
before shipment. It can also be attached on the top according
to the circumstance.
To re-attach the bracket use the threaded holes at the top, with
the camera mounting bracket locking screws 7.
5 Camera-mounting screw hole (1/4 inch)
Use this hole when mounting the camera
onto a fixer, pan/tilt unit, and the like.
(Use a screw shorter than 7 mm.)
(੬ Page 18)
MAX.
7mm
6 Rotation prevention hole
Make use of this rotation-preventive hole to prevent any fall
when mounting the camera. Make sure that the camera is se-
curely mounted.
7 Camera mounting bracket fixing screws (× 2: M2.6 × 6 mm)
Be sure to use a 6 mm long screw.
Names and Operations of Parts
9
INTRODUCTION
Names and Operations of Parts
[Rear Panel]
DC12V
AC24V
SEE INST-
1
2
RUCTION
MANUAL
8
CLASS 2 ONLY (U TYPE)
ISOLATED POWER ONLY
(E TYPE)
9
0
A
B
SET
SELECTOR
POWER
LL
VIDEO OUT
INT
C
8 [DC 12V, AC 24V] Power input terminals
To input DC 12V or AC 24V power.
9 [VIDEO OUT] Video signal output connector
This BNC connector outputs a composite video signal. Con-
nect this to the video input connector of a video monitor,
switcher, etc.
0 [POWER] Power indicator lamp
This lamp lights when power is supplied to the camera.
1D0ownload from Www.Somanuals.com. All Manuals Search And Download.
A [SET] button
During normal screen display, pressing and holding this button
for more than 2 seconds will display the MENU screen.
(੬ Page 24)
During MENU screen display, this button is pressed to display
or enable the selected menu item. The input digit will change
when entering the camera title.
When selecting EXIT in the TOP MENU screen, pressing this
button will return to the normal screen.
B [SELECTOR] button
Used when performing menu settings.
This button is a multidirectional switch.
Ⅵ Pressing in a vertical direction (6 or 7) will select the menu
item.
Ⅵ Pressing in a horizontal direction (8 or t) will change the
set value of the item. When entering the camera title, the
input character will change.
C [INT/ LL] Selector Switch for Synchronizing System
This switch can set a synchronizing system of the camera.
INT:
This is set for internal synchronization (INT) .
LL (Line Lock):
The camera’s vertical synchronization is locked to the AC 24V
power line frequency.
When switching between multiple cameras using a switcher,
selecting this mode and adjusting the vertical phase can re-
duce the monitor sync disturbances occurring when the cam-
era image is switched. (This cannot be used in regions where
the power frequency is 50 Hz (60 Hz) . ( ): TK-WD310E)
(INT: At time of factory shipment)
Download from Www.Somanuals.com. All Manuals Search And Downloa1d.1
INTRODUCTION
Names and Operations of Parts
[Side Panel]
COLOR VIDEO CAMERA
IRIS
VIDEO DC
E
D
D [VIDEO/DC] Iris Selector Switch
This should be set according to the type of lens if an automatic
iris control lens is used.
VIDEO : In case of lens with EE amp built-in.
(੬ Page 20)
DC
: In case of lens without EE amp built-in.
(੬ Page 14)
(DC : At time of factory shipment)
E [IRIS] Iris Terminal
This is connected to an automatic iris control lens.
(੬ Page 15)
1D2ownload from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION/INSTALLATION
Basic System
Ⅵ System with up to 8 cameras
Power
cable
Camera 1
AC24V or
DC12V
COLOR VIDEO CAMERA
Video signal cable
Camera 2
AC24V or
DC12V
COLOR VIDEO CAMERA
Camera 8
AC24V or
DC12V
COLOR VIDEO CAMERA
•
•
•
•
•
•
Monitor
Monitor
DVR, etc.
REC
SR-L910
OPERATE
R
E
C
S
T
O
P
/
E
J
E
C
T
CHECK
VIDEO CAETTE RCRDER
PAUSE/
STILL
O
P
E
.
L
O
C
K
REVERSE
REW
PLAY
COUNT/
CLOCK
SHIFT/TRACKING
RESET
/CANCEL
MENU
FF
TIME
MODE
TIMER
REC
SET/V.LOCK
AL/PL
RESET
Switcher
Download from Www.Somanuals.com. All Manuals Search And Downloa1d.3
CONNECTION/INSTALLATION
Mounting the lens
Mount the lens according to the procedures described below.
Lens mount
1.
(b)
F
(c)
3.
4.
COLOR VIDEO CAMERA
IRIS
IRIS
VIDEO DC
VIDEO
DC
3
4
1
2
2.
5.
3
1
Ferrite core
4
2
1D4ownload from Www.Somanuals.com. All Manuals Search And Download.
1. Before mounting a lens, check whether it is CS-mount lens.
Dimension (b) of the lens shown in the illustration must be as
shown in the table below. If (b) exceeds the value in the table,
it may damage the inside of the camera or correct mounting
may be impossible; never use such lenses. The F mark indi-
cates a focal point.
Lens
Flange back (c)
12.5mm
Dimension (b)
5.5mm or less
CS mount lens
* When using the C-mount lens, use the conversion ring
(CM46633-001, MOUNT ADAPTOR).
2. Attach the included ferrite core to the lens cable. Please at-
tach it as close to the camera as possible.
3. Mount the lens on the camera by turning the lens clockwise.
Adjust its position.
4. When using an auto-iris lens with an EE amplifier, turn the
switch to the “VIDEO” side. When no EE amplifier is equipped,
turn the switch to the “DC” side.
5. If the lens has an auto-iris mechanism, connect the lens cable
after checking the pin arrangement.
If the lens cable has a different type of plug, use the 4-pin plug.
[4-pin plug part no: SCV2859-001]
Contact your dealer of purchase concerning the 4-pin plug.
Lens DC IRIS
VIDEO IRIS
Pin No.
(does not contain EE amplifier) (contain EE amplifier)
–
+
+
1
2
3
4
Brake
Brake
Drive
Drive
9V [max 50mA]
NC
VIDEO
GND
–
Download from Www.Somanuals.com. All Manuals Search And Downloa1d.5
CONNECTION/INSTALLATION
Connections on the back
● Turn off the power supply to all components before making
connections.
Power supply (DC 12 V or AC 24 V)
DC12V
AC24V
SEE INST-
1
2
RUCTION
MANUAL
CLASS
2
ONLY (U TYPE)
ISOLATED POWER ONLY
(E TYPE)
SET
SELECTOR
POWER
LL
VIDEO OUT
INT
Monitor
Ⅵ Video signal cable (BNC)
Connect the coaxial cables (BNC) to the VIDEO OUT connec-
tor (BNC).
1D6ownload from Www.Somanuals.com. All Manuals Search And Download.
Ⅵ Power supply (DC 12 V or AC 24 V)
Connect the DC 12 V or the AC 24 V power supply to the DC
12V/AC 24V terminals. To prevent connection errors or a cable
disconnection, we recommend the use of lug plates for the con-
nections.
The following table shows the connection distances and con-
nection cables provided that 2-conductor VVF cables (vinyl-in-
sulated vinyl sheath cables) are used.
Maximum extension
(reference)
100 m
260 m
410 m
500 m
1.0φmm 1.6φmm 2.0φmm 2.6φmm
and more and more and more and more
Conductor diameter
Memo
● If thin cables are used (i.e. with a high resistance), a signifi-
cant voltage drop will occur when the unit is at its maximum
power consumption. Either use a thick cable to restrict the
voltage drop at the camera side to below 10%, or place the
power supply near to the camera. If voltage drop occurs dur-
ing operation, the performance will be unstable.
● Attach the cable conductors so that they do not come into
contact with the drop prevention wires.
● Do not allow input from both a DC 12 V and AC 24 V power
supply at the same time.
● When using a DC 12 V power supply, ensure that the polari-
ties of the cable are correct.
● The AC 24 V power supply should conform to the following:
U type: Class 2 only
E type: Isolated power supply only
Download from Www.Somanuals.com. All Manuals Search And Downloa1d.7
CONNECTION/INSTALLATION
Mounting the camera
Camera mounting
screw hole
Camera mounting
bracket
Rotation prevention hole
When mounting the camera on a fixer, pan/tilt, etc., use the cam-
era mounting screw hole located on the camera-mounting bracket.
CAUTION:
Use the screw with a length shorter than
7mm from a camera-mounting face.
MAX.
7mm
Furthermore, make use of the rotation prevention hole to prevent
the camera from falling and securely mount the camera.
Special precautions must be taken for mounting the camera on a
wall or a ceiling. We are not liable for any damage caused by im-
proper installation.
1D8ownload from Www.Somanuals.com. All Manuals Search And Download.
DC12V
AC24V
SEE INST-
RUCTION
MANUAL
1
2
CLASS
2
ONLY (U TYPE)
6mm
2mm
ISOLATED POWER ONLY
(E TYPE)
SET
SELECTOR
POWER VIDEO OUT
LL
INT
M3 × 6
Fall Prevention
•
Exercise maximum caution when installing the unit to the wall
or ceiling. You should not engage in the installation work your-
self. Ask a professional to do the job, since the fall of the unit
can result in injuries and accidents.
•
•
When installing the unit on a fixer, Pan/Tilt unit, etc., make sure
to install it firmly using a rotation-preventing hole provided to
prevent fall.
To prevent fall, connect the unit to a section with sufficient
strength (ceiling slab or channel) using a fall prevention wire
such as a wire chain and the like. Use the black screw on the
back of the unit for installation.
Pay utmost attention to the length of the wire, too.
Specified screw (M3 × 6 mm)
•
Never use any screw longer than the specified length as the
inside can be damaged.
Download from Www.Somanuals.com. All Manuals Search And Downloa1d.9
CONNECTION/INSTALLATION
Auto iris lens adjustment
Connect the camera according to the connection method, turn it
on, display an image on the monitor, and check the image. The
white balance adjustment mode is selected. ੬ Page 32 “WHITE
BALANCE”
The camera has been factory-adjusted to the best position, but it
may need to be adjusted according to the object conditions or com-
bination of lenses. If the image is unnatural, adjust it as follows:
(Also read the instruction manual of the lens.)
Ⅵ For video auto iris lens (auto iris lens with built-in
EE amp)
Set the VIDEO/DC switch on the side of the unit to “VIDEO” and
adjust the LEVEL volume on the lens.
Level adjustment
COLOR VIDEO CAMERA
ALC adjustment
(Does not operate)
2D0ownload from Www.Somanuals.com. All Manuals Search And Download.
• LEVEL adjustment
Monitor screen
Too bright
LEVEL turning direction
Counterclockwise (Toward L)
Clockwise (Toward H)
Too dark
Memo
● If the sensitivity adjustment LEVEL is turned excessively to
L, the sensitivity increases because of the AGC function of
the camera, and the image looks grainy.
● At Low light levels, video iris lens may “Hunt”. Please adjust
iris level on lens to minimise hunting.
Ⅵ For DC auto iris lens (auto iris lens without built-in
EE amp)
Set the VIDEO/DC switch on the side of the unit to “DC” and
adjust the LEVEL in the LENS ADJUST screen. (੬ Page 34)
Download from Www.Somanuals.com. All Manuals Search And Downloa2d.1
CONNECTION/INSTALLATION
Back focus adjustment
Be sure to make back-focus adjustments when changing the lens
mounting method or using a different lens.
● To make accurate back focus adjustments, carry out adjustments
in a state where the lens iris is released.
To open the lens iris, set MODE in the FOCUS ADJUST menu
screen to ON. (੬ Page 27)
● The auto iris lens may operate under extremely bright condi-
tions (7000lx or higher). In this case, use an ND filter to adjust
the amount of light.
(The ND fiter acts to reduce the amount of incident light enter-
ing the lens evenly over the entire wavelength band.)
Lens focus ring
Back focus adjust ring
Phillips screwdriver
Back focus locking screws
Memo
If the iris cable length of the lens is insufficient when turning
the back focus adjustment rings, lock the back focus locking
screws, turn the lens and loosen the back focus locking screws
again for achieving back focus.
2D2ownload from Www.Somanuals.com. All Manuals Search And Download.
• With a fixed-focus lens
If the focus can not be adjusted correctly by rotating the lens focus
ring, adjust the back focus as follows.
1. Loosen the back focus locking screws by turning it counter-
clockwise ( ) with a Phillips screwdriver. (2 locations)
2. Shoot a pattern closely.
3. Turn the lens focus ring to ∞.
4. Turn the back focus adjustment ring to focus at the best point.
5. Tighten the back focus locking screws by turning it clockwise
(
). (2 locations)
• With a zoom lens
If the image is out of focus when zooming (telephoto wide-angle),
adjust the camera as follows:
1. Loosen the back focus locking screws by turning it counter-
clockwise ( ) with a Phillips screwdriver. (2 locations)
2. Shoot a comparatively dark scene with thin lines.
3. Set the lens to the maximum telephoto position, and adjust
the lens focus.
4. Set the lens to the maximum wide-angle position, and turn
the back focus ring to adjust the focus.
(Repeat steps 3. and 4. two or three times.)
5. Tighten the back focus locking screws by turning it clockwise
(
). (2 locations)
Download from Www.Somanuals.com. All Manuals Search And Downloa2d.3
MENU SETTING
Menu settings
DC12V
AC24V
SEE INST-
1
2
RUCTION
MANUAL
CLASS 2 ONLY (U TYPE)
ISOLATED POWER ONLY
(E TYPE)
SET
SELECTOR
POWER
LL
VIDEO OUT
INT
SELECTOR
button
SET button
Operation
Cursor
— — —
— — —
MENU
1. Press and hold the SET button
for more than 2 seconds.
F OCUS A D J US T..
V I D EO A D J US T..
CAMERA S ET T I NGS ..
F AC T OR Y S ET T I NGS ..
EX I T
● The MENU screen appears.
2. Press the SELECTOR button in
the vertical direction (6 or 7)
and move the cursor (>) to the
desired submenu.
Submenu (“..” displayed
at the end.)
3. Press the SET button
● The selected submenu screen
appears.
— — — V I D E O A D J UST — — —
WDR
AGC
M
D E
MODE 2
L OW
MODE
A TW
WH I T E B A L ANC E
COL OR L E VE L
E N HA NCE L E V E L
E X I T
NORMAL
NORMAL
2D4ownload from Www.Somanuals.com. All Manuals Search And Download.
4. Press the SELECTOR button in
the vertical direction (6 or 7)
and move the cursor (>) to the
desired item.
— — —
— — —
V I D E O A D J UST
D E
WDR
AGC
M
MODE 2
L OW
A TW
NORMAL
NORMAL
MODE
WH I T E B A L ANC E
COL OR L E VE L
E N HA NCE L E V E L
E X I T
5. Press the SELECTOR button in
the horizontal directional (8 or
t) and change the set value.
Ⅵ To change the set value of mul-
tiple items, repeat steps 4. and
5. above.
— — —
— — —
V I D E O A D J UST
D E
WDR
AGC
M
MODE 2
H I GH
MODE
WH I T E B A L ANC E
COL OR L E VE L
E N HA NCE L E V E L
E X I T
A TW
NORMAL
NORMAL
6. Exit the menu screen.
Move the cursor (>) to EXIT of
the menu screen and press the
SET button.
— — —
— — —
V I D E O A D J UST
D E
WDR
AGC
M
MODE 2
H I GH
A TW
NORMAL
NORMAL
MODE
WH I T E B A L ANC E
COL OR L E VE L
E N HA NCE L E V E L
E X I T
7. Return to the normal screen.
Move the cursor (>) to EXIT of
the MENU screen and press the
SET button.
● The screen returns to the nor-
mal screen (screen with no
menu display).
— — —
— — —
MENU
F OCU S A D J US T..
V I DEO A D J US T..
CAME RA S ET T I NGS ..
F AC T OR Y S ET T I NGS ..
EX I T
Memo
When returning to the normal screen from the TOP MENU
screen by selecting EXIT, the menu settings will be stored
in the unit memory.
Download from Www.Somanuals.com. All Manuals Search And Downloa2d.5
MENU SETTING
Menu tree
The menu screens are structured as shown below.
੬
Page 27
— — —
— — —
OFF
F O C U S A D J UST
MOD E
E X
I
T
੬
Page 28
੬ Page 29
— — —
FO CUS A D J US T..
— — —
— — —
— — —
—
—
WDR CUSTOM SETTINGS
—
—
MENU
V
I
D E O A D J UST
WD R B I AS
WD R MOD E
AGC MOD E
MOD E2
L OW
A TW
NORMAL
NORMAL
– 36
–
3 6
3 6
1 8
V
I
DEO A D J US T..
CAMERA S E T T NGS..
F ACT OR Y S ET T NGS ..
EX
8
I
WH
COL OR L E VE
E N HA NCE L E V E
E X
I
T
E
B A L ANC E
WD R
EXP.
L
I
I
M
I
T
I
L
0
2 5
I
T
L
I
T
B
AS
–18
–4
WD R BR I G HT
10 0
1 0 4
15 0
EX I T
੬
Page 34
੬
Page 33
— — —
— — —
CA MERA SE T T
I
N G S
—
—
MANUAL WHITE BALANCE
—
—
L ENS A DJ U S T ..
R – B
E X
CAME RA
CAME RA
T
T
I
I
T
T
L E
L E E D I
O F F
T
B L UE
R ED
I
T
V
PHASE
0
8
4
1 0
4
Normal screen
EX
I
T
੬
Page 34
— — —
— — —
L E NS A DJ US T
੬
Page 38
DC O F F S E T
1 0
0
1 2
0
1 5
0
— — —
F ACT OR Y S ET T N GS
— — —
I
E X
I
T
CA NC E L
CL EAR
Memo
● When selecting an item with “..” at the end, the submenu
screen will appear.
● When selecting EXIT in each screen, the screen will return
to the previous screen.
When selecting EXIT in the MENU screen, the screen will
return to the normal screen.
2D6ownload from Www.Somanuals.com. All Manuals Search And Download.
About menus
FOCUS ADJUST........... Used during focus adjustment of the auto
iris lens.
(੬ Page 27)
VIDEO ADJUST ............ Sets the wide dynamic range, gain, color
temperature, white balance, etc.
(੬ Page 28)
CAMERA SETTINGS.... Sets the DC iris, camera title and vertical
phase.
(੬ Page 34)
FACTORY SETTINGS... Restores the menu settings to the fac-
tory settings.
(੬ Page 38)
FOCUS ADJUST screen
MODE
Default setting: OFF
Used during focus adjustment of the auto iris lens.
When set to ON, the focus adjustment accuracy is increased by
forcing the iris open and with a shallower focal point.
Memo
When exiting the FOCUS ADJUST screen, MODE will auto-
matically be set to OFF.
Download from Www.Somanuals.com. All Manuals Search And Downloa2d.7
MENU SETTING
VIDEO ADJUST screen
WDR MODE
Default setting: MODE2
Setting of the wide dynamic range (WDR) is performed.
CUSTOM : Manually adjusts the wide dynamic range.
Pressing the SET button will display the WDR CUS-
TOM SETTINGS screen. (੬ Page 30)
MODE1 : When shooting in a bright area outdoors
MODE2 : Standard video
MODE3 : To brighten the video taken indoors
MODE4 : To brighten areas with little luminance in video with
large difference in brightness
(When moving from dark indoors to outdoors during
shooting)
FLUOR : For video taken under lighting (fluorescent lighting,
etc.) that synchronizes with commercial electrical
power supply frequency resulting in periodical change
in colors
(When in a 60Hz area, set to LL (Line Lock).)
(੬ Pages 11, 35)
Memo
● The Wide Dynamic Range feature controls the exposure time
using up to 5 sampling timing within a single screen accord-
ing to the brightness of the subject. With the Wide Dynamic
Range feature, the subject with a large difference in bright-
ness with the remainder of the screen can be viewed in a
clear, natural state even when shooting in areas with large
difference in lighting (such as indoors easily influenced by
backlight, afternoon sun, etc., entrances and near windows).
● Set the mode by first checking under the usage environ-
ment.
2D8ownload from Www.Somanuals.com. All Manuals Search And Download.
WDR CUSTOM SETTINGS screen
The Wide Dynamic Range (WDR) is adjusted manually.
Operation
1. Display the VIDEO ADJUST
— — — V I D E O A D J UST — — —
screen. (੬ Page 24)
WDR MOD E
CUS TOM ..
L OW
AGC MOD E
A TW
WH I T E B A L ANC E
COL OR L E VE L
E N HA NCE L E V E L
E X I T
2. Select WDR MODE and press
the SELECTOR button in the
horizontal direction (8 or t) to
change the setting to CUSTOM.
3. Press the SET button.
NORMAL
NORMAL
● The WDR CUSTOM SET-
TINGS screen will appear.
4. Press the SELECTOR button in
the vertical direction (6 or 7)
and move the cursor (>) to the
item to set.
5. Press the SELECTOR button in
the horizontal direction (8 or t)
to change the set value.
—
— WDR CUSTOM SETTINGS
—
—
WD R B I AS
WD R L I M I T
EXP. B I AS
– 36
0
– 8
2 5
3 6
3 6
1 8
–18
–4
WD R BR I G HT
10 0
1 0 4
15 0
EX I T
Cursor
Set value
6. To exit setting, select EXIT and
press the SET button.
● The screen returns to the
VIDEO ADJUST screen.
Memo
● WDR custom mode allows manual adjustment. (These are
overwritten if other modes are selected.)
● When exiting the WDR CUSTOM SETTINGS screen with-
out changing settings, MODE1 will be automatically selected
for WDR MODE.
Download from Www.Somanuals.com. All Manuals Search And Downloa2d.9
MENU SETTING
VIDEO ADJUST screen (continued)
Item
Content
WDR BIAS
Sets the low/mid luminance level of the Wide
Dynamic Range
● To brighten video with low/mid luminance:
Increase the value
● To darken video with low/mid luminance:
Decrease the value
[Setting range: -36 ~ -8 ~ 36]
WDR LIMIT
EXP. BIAS
Sets the maximum value of the Wide Dynamic Range
● To shoot a subject with large difference in
brightness:
Increase the value
[Setting range: 0 ~ 25 ~ 36]
Adjusts the output properties for the luminance
level of the subject
● To further sharpen a dark subject:
Increase the value
● To further sharpen a bright subject:
Decrease the value
[Setting range: -18 ~ -4 ~ 18]
WDR BRIGHT Adjusts the brightness of the entire video.
● To further brighten the entire video:
Increase the value
[Setting range: 100 ~ 104 ~ 150]
3D0ownload from Www.Somanuals.com. All Manuals Search And Download.
AGC MODE
Default setting: LOW
Sets the maximum gain of AGC (Auto Gain Control).
OFF
LOW
HIGH
: When the AGC feature is not in use
: When there is a shortage of light
: When there is an extreme shortage of light
SUPER : When there is a shortage of light even when setting to
HIGH
Memo
● When raising the gain, noise will appear in the screen for
dark areas.
● When in a dark area and setting AGC MODE to SUPER:
• Red and blues colors as well as residual images may ap-
pear for subjects with motion.
• Video may temporarily lock or noise may be noticeable.
• The entire screen may temporarily change from a dark to
a bright state.
• When especially dark, depending on light intensity, the Wide
Dynamic Range (WDR) feature will not function.
(The WDR feature will function in normal light intensities.)
• The right edge of the screen may temporarily jiggle.
Download from Www.Somanuals.com. All Manuals Search And Downloa3d.1
MENU SETTING
VIDEO ADJUST screen (continued)
WHITE BALANCE
Default setting: ATW
The white balance adjustment mode is selected. White balance
can be adjusted for lighting with color temperature in the range
between 2,500K and 10,000K.
ATW
: The unit will be in the Auto Tracking White Balance mode.
The white balance will be adjusted automatically according
to the color temperature of the lighting.
AWB (SET) : When pressing the SET button (under 1 second), the white
balance will be adjusted automatically for the current lighting
(color temperature).
The result of the white balance automatically adjusted will
be stored in the unit memory.
Use this setting when using the white balance that has been
adjusted automatically.
MANUAL.. : Use this setting when manually adjusting the white balance
for the current lighting (color temperature).
When pressing the SET button, the screen for manually ad-
justing the white balance appears. (੬ Page 33)
The result of the white balance manually adjusted will be
stored in the unit memory.
Use this setting when using the white balance that has been
adjusted manually.
Memo
●
When adjusting the white balance forAWB (SET) or MANUAL, fill
the entire screen with a white subject (such as paper, cloth, etc.).
● AWB (SET) data will be cleared when changing to another
mode (ATW, MANUAL).
● If proper colors cannot be achieved in the ATW mode, use
the AWB (SET) or MANUAL mode.
● In some cases, proper white balance may not be achieved
even in the MANUAL mode for artificial lightning such as
fluorescent lighting, etc.
3D2ownload from Www.Somanuals.com. All Manuals Search And Download.
MANUAL WHITE BALANCE screen
If the entire screen appears to be reddish or bluish in color as the
result of automatic white balance adjustment, manually adjust the
white balance.
Preparation
— — — V I D E O A D J UST — — —
WDR MOD E
MODE 2
Fill the entire screen with a white
subject (such as paper, cloth, etc.).
AGC MOD E
L OW
MAN U AL..
NORMAL
NORMAL
WH I T E B A L ANC E
COL OR L E VE L
E N HA NCE L E V E L
E X I T
Operation
1. Display the VIDEO ADJUST
screen. (
੬
Page 24)
2. Set WHITE BALANCE to
MANUAL and press the SET
button.
—
—
MANUAL WHITE BALANCE
—
—
R – B
B L UE
R ED
E X I T
● The MANUAL WHITE BAL-
ANCE screen will appear.
3. Press the SELECTOR button in
the vertical direction (6 or 7)
and move the cursor (>) to R-B.
4. Press the SELECTOR button in
the horizontal direction (8 or
t).
Set value
Memo
The result of the white
balance adjusted manu-
ally will be stored in the
unit memory.
● Pressing in the 8 direction will
increase bluish tint.
● Pressing in the t direction will
increase the reddish tint.
To use the manually ad-
justed white balance, set
WHITE BALANCE to
MANUAL.
5. To end adjustment, press the
SELECTOR button in the verti-
cal direction (6 or 7) to select
EXIT and press the SET button.
Download from Www.Somanuals.com. All Manuals Search And Downloa3d.3
MENU SETTING
VIDEO ADJUST screen (continued)
COLOR LEVEL
Default setting: NORMAL
The color level of video signals is adjusted.
● To lighten colors: decrease the value.
● To darken colors: increase the value.
[Setting range: -5 ~ NORMAL ~ 5]
ENHANCE LEVEL
Default setting: NORMAL
The aperture control/contour level of the video signals is adjusted.
● Soften video: decrease the value.
● Sharpen video: increase the value.
[Setting range: -5 ~ NORMAL ~ 5]
CAMERA SETTINGS screen
LENS ADJUST screen
This setting is performed when using the DC auto iris lens.
Settings for controlling the DC auto iris operation of the lens are
performed.
Operation
1. Display the CAMERA SET-
— — — L E NS A DJ US T — — —
TINGS screen. (
੬
Page 24)
DC O F F S E T
1 0 0
1 2 0
1 5 0
2. Select LENS ADJUST and press
E X I T
the SET button.
● The LENS ADJUST screen
appears.
3. Press the SELECTOR button in
the horizontal direction (8 or t)
to change the set value. Press-
ing and holding the button will
continuously change the value.
Item
Set value
3D4ownload from Www.Somanuals.com. All Manuals Search And Download.
4. When selecting EXIT and press-
ing the SET button, the screen
will return to the CAMERA SET-
TINGS screen.
Item
Content
DC OFFSET
Standard level (brightness) for controlling the DC
auto iris operation is set.
Increasing the value: the screen will become darker
[Setting range: 100 ~ 120 ~ 150]
Memo
● Depending on the lens, hunching may occur when setting
this value too high. In this case, lower the value.
CAMERA TITLE
Default setting: OFF
Whether to display the camera title is set.
OFF : Camera title is not displayed.
ON : Camera title is displayed.
V PHASE
Vertical phase during line lock is adjusted. The vertical phase can
be adjusted to other cameras. This setting is enabled when the LL/
INT switch on the back of the unit is set to LL.
● Press the SELECTOR button in
— — — CA MERA SE T T I N G S — — —
the horizontal direction (8 or t)
L ENS A DJ U S T ..
CAME RA T I T L E
O F F
to set. Pressing in the button to
the right (t) will advance the
phase and pressing to the left
(8) will delay the phase.
CAME RA T I T L E E D I T
V
PHASE
0
84
1 0 4
EX I T
Download from Www.Somanuals.com. All Manuals Search And Downloa3d.5
Set value
MENU SETTING
CAMERA SETTINGS screen (continued)
CAMERA TITLE EDIT screen
Up to 24 characters can be entered for the camera title. The en-
tered camera title will appear on the bottom left of the screen when
the CAMERA TITLE menu item is set to ON.
Operation
1. Display the CAMERA SET-
— — — CA MERA SE T T I N G S — — —
TINGS screen. (੬ Page 24)
L ENS A DJ U S T ..
CAME RA T I T L E
O F F
2. Press the SELECTOR button in
the vertical direction (6 or 7)
and move the cursor (>) to se-
lect CAMERA TITLE EDIT.
3. Press the SET button.
CAME RA T I T L E E D I T
V
PHASE
0
84
1 0 4
EX I T
● The 1st character will appear
in purple and input will be al-
lowed.
1st character
4. Press the SELECTOR button in
the horizontal direction (8 or t)
and select the desired charac-
ter.
5. Press the SET button to confirm
the 1st character. The 2nd char-
acter will then appear in purple.
6. Repeat steps 4. and 5. above to
enter up to 24 characters.
7. To end character entry, press the
SELECTOR button in the verti-
cal direction (6 or 7) and move
the cursor (>) to another item.
To correct a character, press
the SET button to display the
character to correct in
purple, press the SELEC-
TOR button in the horizontal
direction (8 or t) to
change the character.
3D6ownload from Www.Somanuals.com. All Manuals Search And Download.
Ⅵ Allowed characters
8 direction (SELECTOR button) t direction
Space
Pressing the SELECTOR button in the t direction will select
the character on the right and pressing in the 8 direction will
select the character on the left. Pressing and holding the button
will continuously change the character selected.
Memo
When CAMERA TITLE is set to ON, a background the width of 1
character is displayed, even when there is no camera title entered.
If a CAMERA TITLE of more than 1 character is entered, a
background the width of 24 characters is displayed.
Download from Www.Somanuals.com. All Manuals Search And Downloa3d.7
MENU SETTING
FACTORY SETTINGS screen
Returns set values to their factory settings.
Operation
1. Display the FACTORY SET-
TINGS screen. (੬ Page 24)
2. Press the SELECTOR button in
the vertical direction (6 or 7)
and move the cursor (>) to
CLEAR.
— — —
— — —
ME NU
F OCUS A D J U S T ..
V I D EO A D J US T ..
CAME RA S E T T I NGS..
F AC T OR Y S E T T I NGS ..
E X I T
3. Press the SET button.
● Settings including the camera
title will be restored to the fac-
tory settings and the screen
will return to the MENU
screen.
Cursor
— — — F ACT OR Y S ET T I N GS — — —
CA NCE L
CL E AR
* Select CANCEL and press the
SET button to return to the
MENU screen without chang-
ing settings.
4. Exit the menu screen.
Select EXIT within the MENU
screen and press the SET but-
ton to return to the normal
screen.
3D8ownload from Www.Somanuals.com. All Manuals Search And Download.
OTHERS
Troubleshooting
Symptom
Remedy
Drop in voltage of the power supply can
be considered. Check the length and thick-
ness of the power supply cable.
(੬ Page 17)
The operation becomes un-
stable
Set the VIDEO/DC switch on the side of
unit according to the type of auto iris lens
used.
The auto iris will not operate
(੬ Pages 20, 21)
Lower the gain using the AGC MODE
menu item.
There is noise in the screen
or increase in residual images
SUPER
(MAX)
HIGH
LOW
OFF
(MIN)
Gain
(੬ Page 29)
When using in an environment where there
are changes in the light source, set the
WHITE BALANCE menu item to ATW.
(੬ Page 32)
The colors of the screen are
not natural
Set the WHITE BALANCE menu item to
AWB or MANUAL.
(੬ Page 32)
White balance adjusted
automatically/manually
cannot be used
Set the CAMERATITLE menu item to ON.
(੬ Page 35)
The camera title will not ap-
pear
When adjusting the vertical phase during
line lock, set the LL/INT switch on the back
of unit to LL.
The vertical phase cannot be
adjusted using the V PHASE
menu item
(੬ Page 35)
Download from Www.Somanuals.com. All Manuals Search And Downloa3d.9
OTHERS
Speifications
Image pickup device
: 1/3 type WDR digital image device
Number of effective pixeis : 380,000 pixels ((H) 720 × (V) 540)
Synchronizaton method
Scanning frequency
: Internal,Line lock
:
U Type (H) 15.734 kHz, (V) 59.94 Hz
E type (H) 15.625 kHz, (V) 50.0 Hz
Resolution
: 480 TV lines (H)
VIDEO OUT
: Composite video signal
1 V(p-p), 75Ω (BNC)
: 48 dB (AGC OFF)
Video S/N ratio
Minimum required illumination : 2.5 lx (50%, F1.2, AGC SUPER,
WDR MODE 2)
Lens mount
: CS mount
Power supply
: AC 24 V ` 50 Hz/60 Hz
DC 12 V
Power consumption
Ambient temperature
: U type Approx. 5.7 W
E type Approx. 400 mA
: –10°C to 50°C (operation)
0°C to 35°C (recommended)
Mass
: 330 g
Accessory
: Instructions ........................1
Ferrite core ........................1
Design and specifications are subject to change without notice.
4D0ownload from Www.Somanuals.com. All Manuals Search And Download.
Ⅵ External Dimensions (Unit: mm)
U1-32
50
107
95
COLOR VIDEO CAMERA
TRIPOD BASE
33
1/4-20UNC
MOUNTING HOLE
Download from Www.Somanuals.com. All Manuals Search And Downloa4d.1
VICTOR COMPANY OF JAPAN, LIMITED
is a registered trademark owned by VICTOR COMPANY OF JAPAN, LTD.
is a registered trademark in Japan, the U.S.A., the U.K. and other countries.
Printed in Japan
© 2004 VICTOR COMPANY OF JAPAN, LIMITED
LWT0127-001A
|