SRX700 Series User’s Guide
Part Number: 354538-002
BEFORE YOU BEGIN
SRX725
SRX728S
SRX715
SRX738
SRX722
SRX712M
SRX718S
The SRX700 speakers covered by this manual are not intended for fixed installation in outdoor or high moisture
environments. Moisture can damage the speaker cone and surround and cause corrosion of electrical contacts
and metal parts. Avoid exposing the speakers to direct moisture. Keep speakers out of extended or intense direct
sunlight. The driver suspension will prematurely dry out and finished surfaces may be degraded by long-term
exposure to intense ultra-violet (UV) light.
SRX700 speakers can generate considerable energy. When placed on a slippery surface such as polished wood
or linoleum, the speaker may move due to its acoustical energy output. Precautions should be taken to assure
that the speaker does not fall off a stage or table on which it is placed.
Stand mounting safety precautions
Some SRX700 models include a 35 mm receptacle cup to allow mounting on tripod stands or on a pole over
subwoofers. When using stands or poles, be sure to observe the following precautions:
;
;
Check the stand or pole specification to be certain the device is designed to support the weight of the
speaker. Observe all safety precautions specified by the manufacturer.
Always verify that the stand (or subwoofer / pole) is placed on a flat, level, and stable surface and be sure to
fully extend the legs of tripod type stands. Position the stand so that the legs do not present a trip hazard.
;
;
Route cables so that performers, production crew, and audience will not trip and topple the speakers over.
Inspect the stand (or pole and associated hardware) before each use and do not use equipment with worn,
damaged, or missing parts.
;
;
Do not attempt to place more than one SRX700 speaker on a stand or pole.
Always be cautious in windy, outdoor conditions. It may be necessary to place additional weight (i.e. sand
bags) on the base of the stand to improve stability. Avoid attaching banners or similar items to any part of a
speaker system. Such attachments could act as a sail and topple the system.
;
Unless you are confident that you can handle the weight of the speaker, ask another person to help you get
it onto the tripod stand or pole.
Hearing damage, prolonged exposure to excessive SPL
SRX700 loudspeakers are easily capable of generating sound pressure levels (SPL) sufficient to cause perma-
nent hearing damage to performers, production crew and audience members. Caution should be taken to avoid
prolonged exposure to SPL in excess of 90 dB.
3
SPECIFICATIONS
SRX712M - 12¨, two-way, bass-reflex, stage-monitor / utility
Frequency Range (-10 dB):
Frequency Response (±3 dB):
Coverage Pattern:
Crossover Modes:
Crossover Frequency:
70 Hz - 20 kHz
83 Hz - 18 kHz
90º x 50º nominal
Bi-amp / passive, externally switchable
1.2 kHz
Power Rating (Continuous¹/ Program/ Peak): Passive: 800 W / 1600 W / 3200 W
Bi-amp LF: 800 W / 1000 W / 3200 W
Bi-amp HF: 75 W / 150 W / 300 W
Maximum SPL²:
System Sensitivity (1w @ 1m):
LF Driver:
HF Driver:
Nominal Impedance:
131 dB SPL peak
96 dB SPL (passive mode)
1 x JBL 2262H 305 mm (12 in) Differential Drive® woofer with neodymium-magnet and dual voice-coils
1 x JBL 2431H 75 mm (3 in) voice-coil, neodymium-magnet compression driver
Passive: 8 ohm
Bi-amp LF: 8 ohms
Bi-amp HF: 8 ohms
Active Tunings:
Enclosure:
Suspension / Mounting:
Transport:
dbx DriveRack, all models. Settings available at www.jblpro.com
Symmetrical stage monitor, 15 mm, 11-ply birch plywood.
Dual angle, 35 mm pole socket 2 x M10 fittings for optional SRX712M-YK yoke
Integrated handle / input cup
Finish:
Black DuraFlex™ finish
Grille:
Powder coated, black, 16-gauge perforated steel with acoustically transparent charcoal foam backing
Neutrik ® Speakon® NL-4 (x2), one on each end
349 mm x 546 mm x 260 mm (13.75 in x 21.5 in x 10.25 in)
15 kg (33 lb)
Input Connectors:
Dimensions (H x W x D):
Net Weight:
Optional Accessories:
SRX712M-CVR: Pull-over padded cover
SRX712M-YK: Suspension, mounting yoke
SS2-BK: tripod speaker stand
SS3-BK: satellite speaker pole, 35 mm diamter, 41 in (1041 mm)
SRX715 - 15¨, two-way, bass-reflex (suspendable version, SRX715F)
Frequency Range (-10 dB):
Frequency Response (±3 dB):
Coverage Pattern:
Crossover Modes:
Crossover Frequency:
43 Hz - 20 kHz
53 Hz - 20 kHz
75º x 50º nominal
Bi-amp / passive, externally switchable
1.2 kHz
Power Rating (Continuous¹/Program/Peak): Passive: 800 W / 1600 W / 3200 W
Bi-amp LF: 800 W / 1600 W / 3200 W
Bi-amp HF: 75 W / 150 W / 300 W
Maximum SPL²:
System Sensitivity (1w @ 1m):
LF Driver:
HF Driver:
Nominal Impedance:
131 dB SPL peak
96 dB SPL (passive mode)
1 x JBL 2265H 380 mm (15 in) Differential Drive® woofer with neodymium-magnet and dual voice-coils
1 x JBL 2431H 75 mm (3 in) voice-coil, neodymium-magnet compression driver
Passive: 8 ohms
Bi-amp LF: 8 ohms
Bi-amp HF: 8 ohms
Active Tunings:
Enclosure:
dbx DriveRack, all models. Settings available at www.jblpro.com
Trapezoidal, 15 mm, 11-ply birch plywood
Suspension / Mounting:
Dual-angle (0° or -10°) 35 mm pole socket
5 x suspension points, M10 or optional fly track kit (F version only)
2 x steel handles
Transport:
Finish:
Black DuraFlex™ finish
Grille:
Powder coated, black, 16-gauge perforated steel with acoustically transparent charcoal foam backing
Neutrik® Speakon® NL-4 (x2)
711 mm x 439 mm x 406 mm (28 in x 17.3 in x 16 in)
22 kg (48 lb)
Input Connectors:
Dimensions (H x W x D):
Net Weight:
Optional Accessories:
SRX715-CVR: Pull-over padded cover
SRX-FF3: Flying hardware kit (for use with F versions only)
229-00009-01: Suspension kit, includes 3 x 10 mm forged eyebolts & washers (for use with F versions only)
SS2-BK: tripod speaker stand
SS3-BK: satellite speaker pole, 35 mm diamter, 41 in (1041 mm)
4
¹ IEC filtered noise with 6 dB crest factor.
² Calculated based on peak power rating and sensitivity, 1 m.
SRX722 - Dual 12¨, two-way, bass-reflex (suspendable version, SRX722F)
Frequency Range (-10 dB):
Frequency Response (±3 dB):
Coverage Pattern:
Crossover Modes:
Crossover Frequency:
72 Hz - 20 kHz
81 Hz - 20 kHz
75º x 50º nominal
Bi-amp / passive, externally switchable
1.2 kHz
Power Rating (Continuous¹/Program/Peak): Passive: 1200 W / 2400 W / 4800 W
Bi-amp LF: 1200 W / 2400 W / 4800 W
Bi-amp HF: 75 W / 150 W / 300 W
Maximum SPL²:
System Sensitivity (1w @ 1m):
LF Driver:
HF Driver:
Nominal Impedance:
135 dB SPL peak
97 dB SPL (passive mode)
2 x JBL 2262H 305 mm (12 in) Differential Drive® woofer with neodymium-magnet and dual voice-coils
1 x JBL 2451H 102 mm (4 in) voice-coil, neodymium-magnet compression driver
Passive: 4 ohms
Bi-amp LF: 4 ohms
Bi-amp HF: 8 ohms
Active Tunings:
Enclosure:
dbx DriveRack, all models.Settings available at www.jblpro.com
Trapezoidal, 15 mm, 11-ply birch plywood
Suspension / Mounting:
Transport:
5 x suspension points, M10 or optional track kit (F version only)
2 x steel handles
Finish:
Black DuraFlex™ finish
Grille:
Powder coated, black, 16-gauge perforated steel with acoustically transparent charcoal foam backing
Neutrik ® Speakon® NL-4 (x2)
965 mm x 394 mm x 394 mm (38.0 in x 15.5 in x 15.5 in)
34 kg (76 lb)
Input Connectors:
Dimensions (H x W x D):
Net Weight:
Optional Accessories:
SRX722-CVR: Pull-over padded cover
SRX-FF3: Flying hardware kit (for use with F versions only)
229-00009-01: Suspension kit, includes 3 x 10 mm forged eyebolts & washers (for use with F versions only)
SRX725 - Dual 15¨, two-way, bass-reflex (suspendable version, SRX725F)
Frequency Range (-10 dB):
Frequency Response (±3 dB):
Coverage Pattern:
Crossover Modes:
Crossover Frequency:
37 Hz - 20 kHz
53 Hz - 20 kHz
75º x 50º nominal
Bi-amp / passive, externally switchable
1.2 kHz
Power Rating (Continuous¹/Program/Peak): Passive: 1200 W / 2400 W / 4800 W
Bi-amp LF: 1200 W / 2400 W / 4800 W
Bi-amp HF: 75 W / 150 W / 300 W
Maximum SPL²:
System Sensitivity (1w @ 1m):
LF Driver:
HF Driver:
Nominal Impedance:
136 dB SPL peak
99 dB SPL (passive mode)
2 x JBL 2265H 380 mm (15 in) Differential Drive® woofer with neodymium-magnet and dual voice-coils
1 x JBL 2451H 102 mm (4 in) voice-coil, neodymium-magnet compression driver
Passive: 4 ohms
Bi-amp LF: 4 ohms
Bi-amp HF: 8 ohms
Active Tunings:
Enclosure:
dbx DriveRack, all models. Settings available at www.jblpro.com
Trapezoidal, 15 mm, 11-ply birch plywood
Suspension / Mounting:
Transport:
5 x suspension points, M10 or optional track kit (F version only)
2 x steel handles
Finish:
Black DuraFlex™ finish
Grille:
Powder coated, black, 16 gauge perforated steel with acoustically transparent charcoal foam backing
Neutrik ® Speakon® NL-4 (x2)
1219 mm x 541 mm x 508 mm (48 in x 21.3 in x 20 in)
45 kg (100 lb)
Input Connectors:
Dimensions (H x W x D):
Net Weight:
Optional Accessories:
SRX725-CVR: Pull-over padded cover
SRX-FF3: Flying hardware kit (for use with F versions only)
229-00009-01: Suspension kit, includes 3 x 10 mm forged eyebolts & washers (for use with F versions only)
¹ IEC filtered noise with 6 dB crest factor.
² Calculated based on power rating and sensitivity, 1 m.
5
SRX738 - 18¨, three-way, bass-reflex (suspendable version, SRX738F)
Frequency Range (-10 dB):
Frequency Response (±3 dB):
Coverage Pattern:
35 Hz - 20 kHz
44 Hz - 20 kHz
60º x 40º nominal
Crossover Modes:
Crossover Frequencies:
Bi-amp / passive, internally switchable
2 kHz / 350 Hz
Power Rating (Continuous¹/Program/Peak): Passive: 800 W / 1600 W / 3200 W
Bi-amp LF: 800 W / 1600 W / 3200 W
Bi-amp HF: 350 W / 700 W / 1400 W
Maximum SPL²:
130 dB SPL peak
System Sensitivity (1w @ 1m):
Mid / High Sensitivity (1w @ 1m):
LF Driver:
MF Driver:
HF Driver:
95 dB SPL (passive mode)
108 dB SPL (bi-amp mode)
1 x JBL 2268H 457 mm (18 in) Differential Drive® woofer with neodymium-magnet and dual voice-coils
1 x JBL CMCD-81H Cone Midrange Compression Driver™, integral 2169H 200 mm (8 in) Differential Drive®
1 x JBL 2431H 75 mm (3 in) voice-coil, neodymium-magnet compression driver
Passive: 8 ohms
Nominal Impedance:
Bi-amp LF: 8 ohms
Bi-amp HF: 8 ohms
Active Tunings:
Enclosure:
dbx DriveRack, all models. Settings available at www.jblpro.com
Trapezoidal, 15mm, 11-ply birch plywood
Suspension / Mounting:
Transport:
5 x suspension points, M10 or optional track kit (F version only)
2 x steel handles
Finish:
Black DuraFlex™ finish
Grille:
Powder coated, black, 16-gauge perforated steel with acoustically transparent charcoal foam backing
Neutrik ® Speakon® NL-4 (x2)
1092 mm x 541 mm x 648 mm (43 in x 21.3 in x 25.5 in)
43 kg (95 lb)
Input Connectors:
Dimensions (H x W x D):
Net Weight:
Optional Accessories:
SRX738-CVR: Pull-over padded cover
SRX-FF3: Flying hardware kit (for use with F versions only)
229-00009-01: Suspension kit, includes 3 x 10 mm forged eyebolts & washers (for use with F versions only)
SRX718S - 18¨, bass-reflex, subwoofer
Frequency Range (-10 dB):
31 Hz - 220 Hz
Frequency Response (±3 dB):
Input Connection Modes:
Recommended Crossover Frequencies:
34 Hz - 220 Hz
Switchable, +1/-1 or +2/-2
HPF: 80 Hz, 24 dB/octave LPF: 80 Hz, 24 dB/octave
Power Rating (Continuous³/Program/Peak): Parallel: 800 W / 1600 W / 3200 W
Maximum SPL²:
Sensitivity (1w @ 1m):
LF Driver:
Nominal Impedance:
Active Tunings:
Mounting:
130 dB SPL peak
95 dB SPL
1 x JBL 2268H 457 mm (18 in) Differential Drive® woofer with neodymium-magnet and dual voice-coils
8 ohms
dbx DriveRack, all models. Settings available at www.jblpro.com
Top mounted M20 threaded socket for optional SS4-BK pole
Rectangular, 18 mm, 13-ply birch plywood
Enclosure:
Finish:
Black DuraFlex™ finish
Grille:
Powder coated, black, 16-gauge perforated steel with acoustically transparent charcoal foam backing
Neutrik® Speakon® NL-4 (x2)
508 mm x 597 mm x 749 mm (20.0 in x 23.5 in x 29.5 in)
36 kg (79 lb)
Input Connectors:
Dimensions (H x W x D):
Net Weight:
Optional Accessories:
SRX718S-CVR: Pull-over padded cover
SS4-BK: Adjustable, heavy-duty pole, M20 thread to 35 mm
WK-4: Caster kit
¹ IEC filtered noise with 6 dB crest factor.
² Calculated based on power rating and sensitivity.
³ 40 Hz - 120 Hz pink noise with 6 dB crest factor.
6
SRX728S - Dual 18¨, bass-reflex, subwoofer
Frequency Range (-10 dB):
27 Hz - 220 Hz
Frequency Response (±3 dB):
Input Connection Modes:
Recommended Crossover Frequencies:
33 Hz - 220 Hz
Switchable, +1/-1 or +2/-2 Internally Selectable, Parallel or Discrete
HPF: 80 Hz, 24 dB/octave LPF: 80 Hz, 24 dB/octave
Power Rating (Continuous¹/Program/Peak): Parallel: 1600 W / 3200 W / 6400 W
Maximum SPL²:
Sensitivity (1w @ 1m):
LF Driver:
136 dB SPL peak
98 dB SPL
2 x JBL 2268H 457 mm (18 in) Differential Drive® woofer with neodymium-magnet and dual voice-coils
Parallel: 4 ohm
Nominal Impedance:
Discrete: 8 ohms x 2
Active Tunings:
Enclosure:
dbx DriveRack, all models. Settings available at www.jblpro.com
Rectangular, 18 mm, 13-ply birch plywood
Finish:
Black DuraFlex™ finish
Grille:
Powder coated, black, 16-gauge perforated steel with acoustically transparent charcoal foam backing.
Neutrik® Speakon® NL-4 (x2)
602 mm x 1067 mm x 838 mm (23.7 in x 42 in x 33 in)
76 kg (166.5 lb)
Input Connectors:
Dimensions (H x W x D):
Net Weight:
Optional Accessories:
SRX728S-CVR: Pull-over padded cover
¹ 40 Hz - 120 Hz pink noise with 6 dB crest factor.
² Calculated based on power rating and sensitivity.
Infrasonic Filter
Settings
Recommended Amplifier Power
Model
SRX712M
SRX715
SRX722
SRX725
SRX738
SRX718S
SRX728S
Full-Range / Parallel
HF
LF / Discrete
800 to 1,600W@8Ω
800 to 1,600W@8Ω
1,200 to 2,400@4Ω
1,200 to 2,400W@4Ω x2
800 to 1,600W@8Ω
800 to 1,600W@2Ω
800 to 1,600W@8Ω x2
HPF 24 dB/ octave
50 Hz
800 to 1,600W@8Ω
800 to 1,600W@8Ω
1,200 to 2,400W@4Ω
1,200 to 2,400W@4Ω
800 to 1,600W@8Ω
800 to 1,600W@4Ω
1,600 to 3,200W@4Ω
150 to 300W@8Ω
150 to 300W@8Ω
150 to 300W@8Ω
150 to 300W@8Ω
350 to 700W@8Ω
n/a
40 Hz
63 Hz
31 Hz
31 Hz
31 Hz
n/a
31 Hz
Infrasonic Filter Settings
It is a good practice to use a High Pass Filter (HPF) to prevent frequencies below the system tuning frequen-
cy from reaching the speaker. Inputting these frequencies to the speaker will not result in any appreciable
acoustic output but will put needless mechanical stress on the woofer and reduce available amplifier head-
room. A High Pass Filter will protect your SRX700 system from excess infrasonic energy with little, if any
loss of significant program content. Refer to the above chart for infrasonic filter settings.
Processor Tunings
System tunings for dbx DriveRack processors have been developed for the SRX700 series. If your
DriveRack was manufactured prior to the release of SRX700, you may obtain the settings from the dbx web-
ware_downloads.htm. The tunings are available in digital format and may be loaded directly into your
DriveRack processor (except DriveRack PA).
The settings are also provided in a .PDF document for owners of the DriveRack PA. For other processors or
for analog crossovers and equalizers, the PDF tunings may be used as a starting point. Be aware that all
digital processor models may not respond identically to a particular setting.
DuraFlex™ Finish
The DuraFlex finish used on your SRX700 series speakers is one of the most rugged finishes ever applied
to a speaker. However, all speaker finishes are subject to damage. Should the DuraFlex finish require repair,
a touch-up kit (Part Number 30052) is available from JBL Professional Parts.
Removable JBL Logo Badge
For applications requiring a more unobtrusive appearance, the JBL badge may be peeled off exposing a
JBL logo that is cut into the grille. Note that the badge may not adhere properly if reattached.
7
INPUT PANELS AND BLOCK DIAGRAMS
SRX712M, SRX715, SRX722 and SRX725
-
1+
1-
HPF
HIGH
FREQ
JBL PROFESSIONAL
Northridge, CA USA
Made in USA
Serial No.
NL4
IN / THRU
+
+
2+
2-
LOW
FREQ
PASSIVE
MODE
-
1+
1-
LPF
IN / THRU
NL4
IN / THRU
2+
2-
LOW
FREQ
+
(SRX722,
SRX725
ONLY)
-
SRX700
BI-AMP
1 LF: _Ω
2 HF: 8Ω
PASSIVE
1 IN: _Ω
2 N/C
+
Serial No.
BI-AMP
1 LF: 8Ω
2 HF: 8Ω
PASSIVE
1 IN: 8Ω
2 N/C
1+
1-
HIGH
FREQ
NL4
IN / THRU
-
SRX712M
2+
2-
PASSIVE
BI-AMP
+
LOW
FREQ
BI-AMP
MODE
-
1+
1-
JBL PROFESSIONAL
Northridge, CA USA
Made in USA
NL4
IN / THRU
2+
2-
LOW
FREQ
(SRX722,
SRX725
ONLY)
+
-
SRX700
SRX738
JBL PROFESSIONAL
Northridge, CA USA
Made in USA
Serial No.
+
1+
HPF
BPF
HIGH
FREQ
1-
NL4
IN / THRU
SRX738
-
+
2+
2-
MID
FREQ
PASSIVE
MODE
-
+
-
IN / THRU
1+
1-
LPF
NL4
IN / THRU
LOW
FREQ
2+
2-
+
BI-AMP
1 LF: 8Ω
2 HF: 8Ω
FULL RANGE
1 IN: 8Ω
2 N/C
1+
1-
HPF
LPF
HIGH
FREQ
NL4
IN / THRU
-
+
2+
2-
MID
Remove input platre to change bi-amp / passive mode
FREQ
BI-AMP
MODE
-
+
-
1+
1-
NL4
IN / THRU
LOW
FREQ
2+
2-
SRX700
SRX718S and SRX728S
JBL PROFESSIONAL
Northridge, CA USA
Made in USA
Serial No.
NL4
1
+
1+
1-
LOW
FREQ 1
-
IN / THRU
_Ω
NL4
IN / THRU
NL4
2
2+
2-
+
-
LOW
FREQ 2
(SRX728S
ONLY)
1+
1-
NL4
NL4
1
2
NL4
IN / THRU
2+
2-
INTERNAL
CONNECTORS
8
SRX700
FLYING AND SUSPENSION
JBL SRX700 series offers 4 models with suspendable capabilities: SRX715F, SRX722F, SRX725F and
SRX738F. Before attempting to suspend your speakers, read and understand the following safety information.
IMPORTANT SAFETY WARNING!
The information in this section has been assembled from recognized engineering data and is intended for infor-
mational purposes only. None of the information in this section should be used without first obtaining competent
advice with respect to applicability to a given circumstance. None of the information presented herein is intended
as a representation or warranty on the part of JBL. Anyone making use of this information assumes all liability
arising from such use.
All information presented herein is based upon materials and practices common to North America and may not
directly apply to other countries because of differing material dimensions, specifications, and/or local regulations.
Users in other countries should consult with appropriate engineering and regulatory authorities for specific
guidelines.
Correct use of all rigging hardware is required for secure system suspension. Careful calculations should always
be performed to ensure that all components are used within their working load limits before the array is suspend-
ed. Never exceed the maximum recommended load ratings.
Before suspending any speaker system always inspect all components (enclosure, rigging frames, pins, eye-
bolts, track fittings, etc.) for cracks, deformations, corrosion, missing, loose or damaged parts that could reduce
strength and safety of the array. Do not suspend the speaker until the proper corrective action has been taken.
Use only load-rated hardware when suspending SRX700 suspendable versions.
Are You New to Rigging?
If you are new to rigging, you should do the following:
;
Read and study JBL Technical Note Volume 1, Number 14: Basic Principles for Suspending
Loudspeaker Systems (available at http://www.jblpro.com/pub/technote/tn_v1n14.pdf).
;
;
Know the rules for safe rigging.
Attend a safe rigging seminar, such as that presented by professionals like Rigging Seminars™ or by
Chain Motor Hoist manufacturers like Columbus McKinnon Corp. (manufacturers of the C/M Lodestar).
;
Meet and establish a relationship with a licensed mechanical or structural engineer. Get in the habit of
asking them questions instead of guessing about their answers. Learn from what they tell you.
;
;
Meet and discuss this aspect of your business with your Insurance Agent.
Research and understand the codes, practices, and requirements in the venues where you intend to
operate your sound system.
General Hardware Information
Any hardware used in an overhead suspension application must be load rated for the intended use. Generally,
this type of hardware is available from rigging supply houses; industrial supply catalogs and specialized rigging
distributors. Local hardware stores do not usually stock these products. Hardware that is intended for overhead
suspension will comply with ASME B30.20 and will be manufactured under product traceability controls.
Compliant hardware will be referenced with a working load limit (WLL) and a traceability code.
Attachment to Structures
A licensed Professional Engineer must approve the placement and method of attachment to the structure prior to
the installation of any overhead object. The following performance standards should be provided to the
Professional Engineer for design purposes; Uniform Building Code as applicable, Municipal Building Code as
applicable, and Seismic Code as applicable.
The installation of the hardware and method of attachment must be carried out in the manner specified by the
Professional Engineer. Improper installation may result in damage, injury or death.
9
Inspection & Maintenance
Suspension systems are comprised of mechanical devices and, as such, they require regular inspection and rou-
tine maintenance to insure proper function ability. JBL SRX700F loudspeakers must be inspected for fatigue at
least annually. The inspection shall include a visual survey of all corners and load bearing surfaces for signs of
cracking, water damage, de-lamination, or any other condition that may decrease the strength of the loudspeaker
enclosure. Accessory rigging hardware provided with or for the JBL SRX700F loudspeakers must be inspected
for fatigue at least annually. The inspection shall include a visual survey of the material for signs of corrosion,
bending or any other condition that may decrease the strength of the fastener. Additionally, any eyebolts shall be
checked for possible spin-out of the enclosure. For all other hardware and fittings, refer to the hardware manufac-
turer's inspection and maintenance guidelines for process.
JBL is not responsible for the application of its products for any purpose or the misuse of this information for any
purpose. Furthermore, JBL is not responsible for the abuse of its products caused by avoiding compliance with
inspection and maintenance procedures or any other abuse.
Prior to suspending the system, an expert, trained and experienced in flying speaker systems should inspect all
rigging parts and components.
Resources
ATM Fly-Ware
M.A.N. Flying Systems
20 Sidar Road
Brook Road Industrial Estate
Rayleigh Essex SS6 7XF
McMaster Carr
(888) RIG-MORE / (310) 834-5914
2100 South Wilmington Avenue
Carson, CA 90810
Various Locations in the USA
For a location near you, visit
JBL Professional - Tech Note Vol. 1 No. 14
“Basic Principles for Suspending Loudspeakers”
Safe Rigging
The JBL SRX700 suspendable version loudspeakers are supplied with built-in internal brackets. The system is
designed to facilitate the suspension of the loudspeaker by a qualified person familiar with rigging hardware and
industry practices. Improper installation may result in damage, injury or death.
Working Load Limit
The working load limit (WLL) of any JBL SRX700 suspendable loudspeaker will be maintained as long as no
more than 136 kg (300 lb) is suspended by a minimum of TWO (2) PRIMARY SUSPENSION points (Track
Suspension), or 46 kg (100 lb) is suspended by TWO (2) of the SECONDARY SUSPENSION points (M10
Forged Shoulder Eyebolts).
Flying for Portable Applications (Primary Suspension)
For portable, temporary suspension of SRX700F models, order the JBL SRX-FF3. This kit includes three detach-
able fly-clips. For additional suspension components, contact a professional rigging hardware supplier.
Latchmechanismmust be
down and fully engaged
WARNING
Before lifting any speaker using fly-clip attach-
ments, be certain that the latch mechanism of all
fly-clips is fully and properly engaged with the
track. An audible click will be heard.
10
Suspension in Fixed Installations (Secondary Suspension)
For fixed installations of SRX700F models using M10, forged-shoulder eyebolts, order JBL Part number 229-
00009-01 which includes 3 x 10 mm forged eyebolts with washers.
WARNING
Suspension of SRX700 speakers must employ
both top attachment points. When "bridling" an
SRX700,two (2) legs of equal length must be used.
The rear attachment point is a pull-back point and
is intended only for use in adjusting the down-
angle of the speaker enclosure. Only the top and
bottom attachment points are intended for use as
suspension points.
60º
(MAXIMUM)
11
JBL WARRANTY AND CONTACTS
Who Is Protected by This Warranty?
Your JBL Warranty protects the original owner and all subsequent owners so long as: A.) Your JBL product has
been purchased in the Continental United States, Hawaii or Alaska. (This Warranty does not apply to JBL prod-
ucts purchased elsewhere except for purchases by military outlets. Other purchasers should contact the local
JBL distributor for warranty information.); and B.) The original dated bill of sale is presented whenever warranty
service is required.
What does the JBL Warranty cover?
Except as specified below, your JBL Warranty covers all defects in material and workmanship. The following are
not covered: Damage caused by accident, misuse, abuse, product modification or neglect; damage occurring
during shipment; damage resulting from failure to follow instructions contained in your Instruction Manual; dam-
age resulting from the performance of repairs by someone not authorized by JBL; claims based upon any mis-
representations by the seller; any JBL product on which the serial number has been defaced, modified or
removed.
Who Pays for What?
JBL will pay all labor and material expenses for all repairs covered by this warranty. Please be sure to save the
original shipping cartons because a charge will be made if replacement cartons are requested. Payment of ship-
ping charges is discussed in the next section of this warranty.
How to Obtain Warranty Performance
If your JBL product ever needs service, write or telephone us at JBL Incorporated (Attn: Customer Service
Department), 8500 Balboa Boulevard, PO. Box 2200, Northridge, California 91329 (818/893-8411). We may
direct you to an authorized JBL Service Agency or ask you to send your unit to the factory for repair. Either way,
you'll need to present the original bill of sale to establish the date of purchase. Please do not ship your JBL prod-
uct to the factory without prior authorization. If transportation of your JBL product presents any unusual difficul-
ties, please advise us and we may make special arrangements with you. Otherwise, you are responsible for
transporting your product for repair or arranging for its transportation and for payment of any initial shipping
charges. However, we will pay the return shipping charges if repairs are covered by the warranty.
Mailing Address:
Outside the USA:
JBL Professional
8500 Balboa Blvd.
Northridge, CA 91329 USA
Contact the JBL Professional Distributor in your area. A
complete list of JBL Professional international distributors is
Shipping Address:
Product Registration:
JBL Professional
8370 Balboa Blvd., Dock D
Northridge, CA 91329 USA
(Do not return product to this address without
first obtaining prior authorization from JBL)
Customer Service:
Monday through Friday
8:00am - 5:00pm
Pacific Coast Time In the U.S.A.
(800) 8JBLPRO (800.852.5776)
On the World Wide Web:
|