JBL MP3 Docking Station ON Stage Micro II User Manual

iPhone not included  
User Guide  
English ........................ 2  
Deutsch....................... 8  
Français......................15  
Español ..................... 22  
Italiano......................29  
Dutch ........................ 36  
Korean....................... 43  
Norwegian ................ 50  
Danish........................57  
Japanese....................64  
Simplified Chinese.....71  
Finnish ...................... 78  
Russian ......................85  
Português..................92  
®
®
*
jblonstage micro IIspeaker dock for iPhone/iPod  
 
fcc regulations  
FCC Information for Users  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference;  
and (2) this device must accept any interference received, including interference that may cause undesired operation.  
Radio and Television Interference  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,  
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference  
will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment  
off and then on, the user is encouraged to try to correct the interference by one or more of the following measures:  
• Increase the separation between the equipment and receiver.  
• Connect the equipment to a different outlet so that the equipment and receiver are on different branch circuits.  
• Consult the dealer or an experienced radio/TV technician for help.  
Changes or modifications not expressly approved by JBL could void the user’s authority to operate the equipment.  
Battery Disposal  
Alkaline batteries are considered non-hazardous. Rechargeable batteries (i.e., nickel cadmium, nickel metal-hydride, lithium and lithium-ion) are considered  
hazardous household materials and may pose an unnecessary health and safety risk.  
In the European Union and other locations, it is illegal to dispose of any battery with household trash. All batteries must be disposed of in an environmentally sound  
manner. Contact your local waste management officials for information regarding the environmentally sound collection, recycling and disposal of used batteries.  
IC Statement and Warning  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  
3
 
jbl on stage micro II easy setup guide  
Carefully unpack your speaker  
system and identify all its  
components. JBL On Stage  
Micro II, power supply, remote  
and adapter.  
Step 2. Move the battery door to  
the unlocked position to open  
the battery compartment.  
Step 3. Place 4 AAA batteries  
in the battery compartment.  
Step 4. Connect the power adapter  
into the jack labeled “6V DC In” on  
the rear of the JBL On Stage Micro  
II and plug the power adapter into  
a wall outlet or power strip.  
or  
* Auxilary audio  
cables not included  
-
+
Step 5. Place the appropriate iPhone/iPod adapter onto JBL On Stage  
Micro II. Place your iPhone/iPod on the docking connector or connect  
a 3.5mm (1/8") stereo audio cable to the rear of the JBL On Stage  
Micro II. Connect the audio cable to the audio source.  
Step 7. Adjust the volume using  
(+) to increase and (–) to decrease.  
Press both to mute the JBL On  
Stage Micro II. Press either button  
to unmute.  
Step 6. Press the Power button  
on the back of the JBL On Stage  
Micro II. A green LED will light  
when the JBL On Stage Micro II  
system is on.  
Syncing and transfering files with your computer  
Make sure your iPhone/iPod is securely docked into the JBL On Stage Micro II. Connect a USB cable (not included) into the USB jack on the back of the unit, connect other end of the USB cable directly  
to your computer’s USB port. Make sure your iPhone/iPod and iTunes are updated to the latest software version.  
4
 
troubleshooting your jbl on stage micro II  
Technical Specifications  
Troubleshooting  
Possible Problem  
Solution  
Symptom  
Frequency Response:  
70Hz – 20kHz  
No power to the system  
Ensure that the power supply is connected to a live  
power source and properly connected to the JBL On  
Stage Micro II. Note: When the JBL On Stage Micro II  
is powered, a green power LED on the JBL On Stage  
Micro II should light up.  
No sound from the  
JBL On Stage Micro II  
speaker system  
Power adapter plug is not  
inserted correctly  
Power Consumption:  
10W Maximum  
Power Input:  
No volume or low volume  
Touch the volume “Up” (+) pad on the volume  
control to unmute and/or increase the system volume  
level.  
6V/1.5A  
JBL On Stage Micro II Transducer:  
(2) 1" Full range per channel  
Note: Touching the volume “Down” (–) pad lowers  
the system volume. Touching both the (+) and (–)  
volume control pads at the same time will mute the  
system.  
Dimensions:  
Diameter – 6" (150mm)  
Height – 1-3/4" (38mm)  
System Weight:  
2.22 lb (1.01kg)  
Increase the volume level on the audio source device.  
Replace the batteries.  
Input source is low  
Low or drained batteries  
iPhone/iPod is paused  
Battery:  
Size – AAA  
Type – Alkaline, NiMh  
Quantity – 4  
Press the Play button on the iPhone/iPod or remote  
control.  
Note: If the iPhone/iPod is paused more than 10 min-  
utes, press the JBL On Stage Micro II Power button to  
turn the unit back on. Press either (+) or (–)  
to unmute.  
DO NOT MIX BATTERY TYPES.  
iPhone/iPod is paused  
(battery-only mode)  
DO NOT MIX CHARGED AND  
PARTIALLY CHARGED BATTERIES.  
BATTERIES WILL NOT RECHARGE  
WHILE IN JBL ON STAGE MICRO II.  
These specifications are subject to change without notice.  
5
 
Troubleshooting  
Symptom  
Possible Problem  
Solution  
No sound from the JBL On Stage  
Micro II speaker system (continued)  
The JBL On Stage Micro II has been  
muted for more than 10 minutes in the back on. Press either (+) or (–) to unmute.  
battery-only mode  
Press the JBL On Stage Micro II Power button to turn the unit  
No sound, no LED  
No audio signal has been received for  
10 minutes and JBL On Stage Micro II  
is in standby mode  
Make sure audio signal is supplied through docked iPhone/iPod  
or “Audio In” jack.  
No power; green LED is not on  
Wall adapter is not plugged into the  
JBL On Stage Micro II correctly  
Check the connection of the wall adapter.  
Place the wall adapter in a known powered outlet. Test the outlet  
with a lamp or other device.  
Wall adapter is not receiving AC power  
Connect the JBL On Stage Micro II to a known audio source.  
Test the audio source with headphones.  
6
 
Troubleshooting  
Symptom  
Possible Problem  
Solution  
Note  
There is no sound coming from  
the JBL On Stage Micro II.  
No power to unit.  
Make sure that the wall outlet  
or power strip has power.  
Make sure that all switches for  
outlet/power strip are on and  
that all switches for the unit  
are on.  
Is the LED on? If the LED  
is not on, power is not  
getting to your JBL On Stage  
Micro II. Try the solutions  
shown.  
Make sure that the iPhone/iPod  
is properly docked or that the  
auxiliary cable is properly con-  
nected.  
Incorrect source selection.  
Turn up the volume.  
Check the unit with a source  
that you know to be good.  
Connect the “Aux In” cable to  
the headphone jack of your  
iPhone/iPod.  
Sound comes from only one  
side/channel.  
iPhone/iPod or auxiliary cable  
is not seated properly.  
Make sure that the iPhone/iPod  
is seated all the way into the  
docking station.  
If you are using a 3.5mm  
auxiliary extension cable,  
make sure it is a stereo  
cable.  
Make sure that the auxiliary  
cable is seated all the way into  
the jack.  
Try resetting the iPhone/iPod.  
7
 
Troubleshooting  
Symptom  
Possible Problem  
Solution  
Note  
Distortion (static, cracking  
or hissing sounds).  
Audio source or source material  
may be the problem.  
Test the JBL On Stage Micro II  
with another source.  
Does the distortion occur with  
specific songs? If so, check  
the recording or record the  
source again.  
Volume level may be too high.  
Check the volume of the source. Some devices will distort the  
output signal if the volume is  
set to maximum.  
EQ setting may be too high.  
Check the EQ setting on your  
iPhone/iPod or source device.  
It is recommended that you set  
the source device EQ to “Flat”  
or “Off.”  
JBL On Stage Micro II  
emits a loud hum  
or buzzing noise.  
Input cable is not plugged in  
properly.  
Check the input cable connec-  
tion.  
Cable may be bad.  
Replace the cable.  
Ground logo (an unsuitable  
connection).  
Turn the JBL On Stage Micro II  
off and connect it to another  
wall outlet.  
Speaker system experiences  
radio-frequency interference or  
picks up a radio-station trans-  
mission.  
Purchase a ferrite core and  
Input cable may be  
picking up interference.  
wrap the excess cable around it.  
A ferrite core can be purchased  
at your local electronics store.  
8
 
jbl on stage micro II remote easy setup guide  
Volume Down  
Volume Up  
iPhone/iPod Play/Pause1  
Mute/Unmute1  
iPhone/iPod Previous/Rewind  
*Hold for “rewind”  
iPhone/iPod Next/Fast Forward  
*Hold for “fast forward”  
iPhone/iPod Scroll Down  
iPhone/iPod Select/Enter  
iPhone/iPod Scroll Up  
iPhone/iPod Menu  
Additional Features:  
1. In the battery-only mode, the JBL On Stage Micro II loudspeaker dock will turn off to save battery power when muted or paused  
for longer than 10 minutes.  
2. In the wall adapter power supply mode JBL On Stage Micro II will go into standby mode if no audio signal is detected for 10  
minutes. The green LED will turn off. Once an audio signal is detected the speaker will return to normal playing mode and the  
green LED will light up.  
3. iPod touch and iPhone menu navigation may require the user to manually put the iPhone/iPod in music mode.  
4. When the batteries are low the “low battery LED” will turn on. Change batteries immediately or switch to the power adapter.  
9
 
JBL and Odyssey are trademarks of Harman International Industries, Incorporated, registered in the United States and/or other countries.  
*The trademark On Stage is used with permission of OSA International, Inc.  
iPhone is a trademark of Apple Inc., registered in the U.S. and other countries. iPod is a trademark of Apple Inc., registered in the U.S. and other countries. iPhone/iPod not  
included. “Made for iPod” means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple per-  
formance standards. “Works with iPhone” means than an electronic accessory has been designed to connect specifically to iPhone and has been certified by the developer to  
meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.  
Features, specifications and appearance are subject to change without notice.  
JBL et Odyssey sont des marques commerciales de Harman International Industries, Incorporated, déposées aux États-Unis et/ou dans d’autres pays.  
*Le marque “On Stage” est utilisée avec la permission de OSA International, Inc.  
iPhone est une marque commerciale d’Apple Inc., deposée aux États-Unis et dans d’autres pays. iPod est une marque commerciale d’Apple Inc., deposée aux États-Unis et  
dans d’autres pays. iPhone/iPod non inclus. « Made for iPod » signifie qu’un accessoire électronique a été conçu pour assurer la connexion spécifiquement à iPod et a été  
homologué par le développeur pour répondre aux normes de performance d’Apple. « Works with iPhone » signifie qu’un accessoire électronique a été conçu pour assurer la  
connexion spécifiquement à iPhone et a été homologué par le développeur pour répondre aux normes de performance d’Apple. Apple n’assume aucune responsabilité pour  
le fonctionnement de cet appareil, ni pour sa conformité aux normes de sécurité et réglementaires.  
Sous réserve de modification.  
Harman Consumer, Inc.  
8500 Balboa Boulevard, Northridge, CA 91329 USA  
1.516.255.4525 (USA only)  
© 2010 Harman International Industries, Incorporated. All rights reserved. Tous droits réservés.  
Part Number: 950-0282-001  
10  
 

Indesit Freezer UFA 430 I User Manual
Infortrend Network Card A12U A08U G2421 User Manual
Insignia Blu ray Player S BRDVD4 CA User Manual
Insignia DVD Player NS 7PDVDD User Manual
JVC Car Stereo System KS FX940R User Manual
JVC CRT Television AV 14A3 AV 14F3 AV 1435 AV 1438 AV 20N3 AV 21D3 AV 21E3 AV 21F3 AV 21FR3 AV 21LT3 AV 21LTR3 AV 21Q3 User Manual
JVC DVD Player DR M100S User Manual
JVC Speaker SP PW3000 User Manual
JVC Speaker System UX GB9DAB User Manual
Jwin Clock Radio JL 355 User Manual