Automotive Loudspeakers
P-422, P-522, P-622 & P-923 Owner’s Manual
Download from WwGw.SEomaNnuaUls.coImN. AlEl ManuJalsBSeLarch And Download.
Figure 3d
Figure 3a
Hole Cutout
Installation of the P-622 speakers with the Intermount II™
(pat. pend.) mounting system as shown in Figures 3a, 3b, 3c.
Mounting
Ring
Clips
Mounting
Hooks
Rotate
to
Lock
Mounting
Surface
Figure 3c
Foam
Gasket
Hole
Mounting
Slots
Front View
Cutout
Match Notch on
Speaker with
Notch on Trim Ring
Front Mounting
Mounting the P-622 in
165/170mm DIN (European)
installations using the
Intermount II clips
Rotate
to Lock
Slots for
Mounting
Hooks
Figure 3b
Foam Gasket
Grille
Screen
Figure 3e
Grille
Trim Ring
Mounting Ring
Rotate
to Lock
Mounting
Hooks
Mounting for US 6-1/2"
Honda/Toyota
Factory Location
Rear View
Rear Mounting
03
Speaker Placement
Because of the Power Series speakers’
versatile mounting options, there are
many placement options that will achieve
excellent sound quality in your vehicle.
Please consider the following to help you
get the most from your speakers.
1. The most spacious stereo image is
achieved when the left and right speakers
are placed as far apart as possible.
2. The best center image will be achieved
when the distance from the left speaker
and the right speaker are as equal as pos-
sible from your listening position. This is
most easily achieved by placing the
speakers as far forward as possible.
3. Treble is directional in nature. This
means that high frequencies are reduced
as you move off the tweeter’s axis. If pos-
sible, rotate the speakers so that the angle
of the tweeter points across the car to the
listener on the opposite side. This will
make each listener slightly off-axis to the
tweeter that is closest to that listener, but
on axis to the most distant speaker, which
helps compensate for the fact that each
listener is always closer to one speaker
than to the other (see Figures 4a and 4b).
Choosing mounting locations that satisfy
all of the above criteria will provide the
most satisfying performance.
A Note on Power Handling
As a result of their high efficiency, all JBL
loudspeakers will produce reasonable
volume levels in the automotive environ-
ment using very little amplifier power.
However, the use of a small amplifier to
attain very high volume levels could lead
to overdriving the amplifier. This will
generate high distortion levels which can
easily damage loudspeakers, even if the
rated power of the amplifier is below the
rated maximum power handling of the
loudspeaker!
As a general rule, do not turn up the
volume control past the point where
you hear distortion in the form of either
signal distortion from an overdriven
amplifier or mechanical noise from an
overstressed speaker.
For the best performance and speaker
reliability, you should select an amplifier
with an output rating slightly higher than
the maximum power likely to be used to
generate the desired volume levels. This
margin of reserve power will ensure that
the amplifier will not attempt to deliver
more power than its design allows.
Aim Triangle of Tweeter Diffuser
Toward Listener
Installation Warnings
and Tips
• Be careful not to cut or drill into fuel
tanks, fuel lines, brake or hydraulic lines,
vacuum lines or electrical wiring when
working on your vehicle. Inspect behind
panels before you cut or drill.
• Make sure that the speaker will
physically fit in the mounting location. If
door mounting, check for adequate clear-
ance with the window in both closed and
open positions as well as for interference
with the window crank and power
window mechanism. If mounting else-
where, check for clearance around rear
deck torsion bars, glove box or other
structural elements.
• Do not mount speakers where they will
get wet.
• Make sure that it will be easy to run
connecting wires to the speakers. Trace
speaker wire paths before you undertake
mounting.
Figure 4b
System Design
A more advanced system design can be
achieved by adding a Decade,™ GT,
Power, GTi, or equivalent subwoofer to
your Power Series speakers. In this case
the Power Series multi-element speakers
will be used as high and midbass fre-
quency drivers and should have their
extremely low frequencies blocked by
electrical means. Active or passive
crossovers can be used in order to
achieve the best system fidelity and
widest dynamic range. A crossover fre-
quency of between 80Hz and 120Hz is
recommended for the best imaging and
widest dynamic range.
WARNING: Playing loud music over
120dB can permanently damage your
hearing. The maximum volume levels
achievable with JBL speakers combined
with high power amplification may
exceed safe levels for extended listening.
When listening at high volume levels,
always use hearing protection or turn the
volume down!
• Always disconnect the ground wire from
the battery before doing any work on the
vehicle.
CAUTION: Fuel tanks are located directly
beneath the rear deck in some cars. Check
for adequate speaker basket clearance
before considering this location!
Figure 4a
04
Specifications
Multi-Element Loudspeakers
With Injection-Molded Titanium-Composite Woofer Cones and Butyl-Rubber Surrounds
P-923
P-622
P-522
P-422
6" x 9" 3-Way
6-1/2" 2-Way
5-1/4" 2-Way
4" 2-Way
Super Tweeter
Tweeter
3/4" Solid-state
Titanium
Composite
Titanium-
Titanium-
Titanium-
Titanium-
Composite
Composite
Composite
Composite
Balanced Dome
Balanced Dome
Balanced Dome
Balanced Dome
Tweeter Size
1-1/4"
3/4"
3/4"
3/4"
Speaker Impedance
4 Ohms
4 Ohms
4 Ohms
4 Ohms
Recommended Amplifier
Power Range
5 –250W RMS
25Hz – 22kHz
92dB
5 –175W RMS
45Hz – 22kHz
91dB
5 – 150W RMS
55Hz – 22kHz
90dB
5 – 120W RMS
65Hz – 22kHz
90dB
Frequency Response
Sensitivity
Mounting Depth
Drop-in
3-1/16" (78mm)
2-3/16" (56mm)
2-3/8" (61mm)
1-7/8" (48mm)
Service
Should your loudspeaker ever need ser-
vice, return it to the JBL dealer from
whom it was purchased. If for some rea-
son this is impractical, call 800-336-4JBL
for your nearest warranty station. Do not
return products to the JBL factory with-
out prior authorization.
General Care
The loudspeaker grilles may be cleaned
with a slightly damp cloth.
Safety Note
To avoid the dangers of accidental suffo-
cation, please properly dispose of the
plastic bag used in the speaker packaging.
Do not use any cleaners or solvents on
the grilles or the speaker drivers.
05
Declaration of Conformity
We, JBL Europe A/S
Kongevejen 194B
DK-3460 Birkerød
DENMARK
declare in own responsibility, that the products
described in this owner’s manual are in compliance
with technical standards:
EN 50 081-1/1992
EN 50 082-1/3.1995
Steen Michaelsen
JBL Europe A/S
Birkerød. DENMARK. 1/98
JBL Consumer Products
250 Crossways Park Drive
Woodbury, NY 11797
A Harman International Company
Part No. POWSPKRSOM
Made in USA
|