GTO7001
OWNER’S MANUAL
BEDIENUNGS-
ANLEITUNG
MODE D'EMPLOI
MANUAL DE USO
HANDLEIDING
MANUALE DEL
PROPRIETARIO
ANVÄNDARHANDBOK
BRUGSVEJLEDNING
OMISTAJAN
KÄSIKIRJA
PODRĘCZNIK
UŻYTKOWNIKA
РУКОВОДСТВО
ПОЛЬЗОВАТЕЛЯ
ENGLISH
GTO7001 CAR AUDIO SUBWOOFER AMPLIFIER OWNER’S MANUAL
0
7
Installation Warnings and Tips:
• Disconnect the negative (–) lead from your vehicle’s
battery.
• At the installation sites, locate and make a note of all
fuel lines, hydraulic brake lines, vacuum lines and
electrical wiring. Use extreme caution when cutting
or drilling in and around these areas.
• Choose a safe mounting location away from
moisture.
• Make sure there is sufficient air circulation at the
mounting location for the amplifier to cool itself.
Speaker Output Connectors
DBO (Dynamic Bass Optimization) Variable
Subsonic High-Pass Filter With Variable Boost (Q)
• For woofers in tuned (vented) enclosures, set the
Frequency control to a value 10Hz below the
enclosure’s resonance (tuned) frequency.
• For woofers in sealed boxes, set the control to
any value you prefer between 30Hz and 50Hz.
• Set the Boost control according to your
preference, being careful not to apply
enough boost to damage your woofer(s).
A DBO High-Pass Filter Frequency control,
variable between 10Hz and 100Hz. See above
for appropriate settings.
B DBO Boost control provides up to
12dB of boost slightly above the high-
pass filter’s frequency. See above for
appropriate settings.
Remote Level Control (RLC) Connector
• Connect the Remote Level Control (RLC) here,
using the supplied RJ-11 cable.
• Connect the subwoofer to these terminals,
observing proper polarity. Either + or –
terminal may be used. Minimum total
impedance is 2 ohms.
1
2
Fuses
• Replace only with the same type and rating.
Power Input Connectors
• +12V: Connect to the positive terminal of the
vehicle’s battery. 4 AWG wire is recommended.
Install an appropriate fuse holder and fuse (75A
minimum) within 18 inches of the battery. Make
sure the wire is not damaged or pinched during
installation. Install protective grommets when
routing wires through the firewall or other sheet
metal.
• Mount the amplifier, using the supplied hardware.
Specifications
• 425W RMS x 1 channel @ 4 ohms and ≤1% THD + N*
• 700W RMS x 1 channel @ 2 ohms and ≤1% THD + N*
• THD + N: 0.02% (rated power @ 4 ohms)
• Signal-to-noise ratio: 80dB
(reference 1W into 4 ohms)*
• Signal-to-noise ratio: 107dB
(reference rated power into 4 ohms)
• Frequency response: 20Hz – 330Hz (–3dB)
• Max power: 700 watts
* CEA-2006A-compliant
• GND: Connect to the vehicle’s chassis. Refer to
the picture below.
8
Factory Bolt
Ring Connector
Ground Wire
9
A
Power On LED
• Illuminated when the amplifier is on.
Protect LED
• Illuminated under any of the following fault
conditions: battery over/under voltage, short
circuit in speaker wires, amplifier is too hot,
amplifier’s output circuit has failed (DC voltage is
present in the amplifier’s output).
Note: Remove any paint
below ring connector.
Star Washer
B
Setting Input Level
• REM: Connect to the “Remote Out” lead from the
source unit or to a source of switched
12V+ (ACC).
Aux Output Connectors (RCA)
• Nonfiltered pass-through output. Connect to the
input of an additional amplifier.
Input Connectors (RCA)
• Connect to the RCA outputs from the source unit
or signal processor.
Input-Level Control
• Used to match the input level of the amplifier
to the output level of the source unit.
A Turn Input Level control counterclockwise to
6V (minimum).
B With a dynamic music track playing, turn the
3
4
5
head unit’s volume control to the 3/4 position.
C Turn Input Level control clockwise until the
bass output is proportionate to the output of
the high-frequency speakers, according to
your preference.
D Input level is now adjusted correctly.
Setting the Crossover
A Crossover setting for subwoofers.
Note: Acceptable frequency ranges are indicated
in gray.
C
D
B
• See for the adjustment procedure.
6
Low-Pass Filter Frequency Control
• 12dB/octave low-pass filter,
variable from 32Hz to 320Hz.
Remote Level Control
The Remote Level Control, if installed, will allow
you to adjust the level of bass while seated in the
listening position.
C
• See
for the adjustment procedure.
This product is designed for mobile applications and is not
intended for connection to the mains.
A valid serial number is required for warranty coverage.
Features, specifications and appearance are subject to change
without notice.
Declaration of Conformity
We, Harman Consumer Group, Inc.
Harman Consumer Group, Inc.
250 Crossways Park Drive, Woodbury, NY 11797
2, route de Tours
72500 Château du Loir
France
declare in own responsibility that the product described in this owner’s
manual is in compliance with technical standards:
EN 55013:2001+A1:2003
© 2007 Harman International Industries, Incorporated. All rights reserved.
JBL is a trademark of Harman International Industries, Incorporated,
registered in the United States and/or other countries.
EN 55020:2002+A1:2003
Klaus Lebherz
Part No. GTO7001OM 8/07
Harman Consumer Group, Inc.
Château du Loir, France 8/07
www.jbl.com
|