Intex Recreation Water Pump 638 User Manual

(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007  
106  
IMPORTANT  
SAFETY RULES  
Read, Understand, and Follow all  
Instructions Carefully before  
Installing and using this Product.  
TM  
Krystal Clear  
Model 638 Filter Pump  
220 - 240 V~, 50 Hz, 85 W  
Hmax 1.0 m, H min 0.19 m, IPX7  
Max. Water Temperature 35 °C  
For illustrative purposes only.  
Don’t forget to try these other fine Intex products: Pools, Pool Accessories,  
Inflatable Pools and In-Home Toys, Airbeds and Boats available at fine  
retailers or visit our website.  
©2006 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Recreation Corp.  
All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle  
Rechte vorbehalten.  
Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.  
®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous  
licence de/Marcas registradas utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen  
Ländern der Welt in Lizenz von/Intex Marketing Ltd. to/à/a/an Intex Development Co. Ltd., 8th Floor, Dah Sing  
Financial Centre, 108 Gloucester Road, Wanchai, Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach,  
CA 90801 • Distributed in the European Union by/Distribué dans l’Union Européenne par/Distribuido en la unión Europea  
por/Vertrieb in der Europäischen Union durch/Intex Trading B.V., P.O. Box nr. 1075 – 4700 BB Roosendaal – The  
Netherlands  
106**-A0-0701  
 
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007  
106  
IMPORTANT SAFETY RULES  
Read, Understand and Follow All Instructions Carefully Before Installing and Using this Product.  
READ AND FOLLOW ALL INSTRUCTIONS  
WARNING  
To reduce the risk of injury, do not permit children to use this product. Always  
supervise children and those with disabilities.  
• Risk of electric shock. Connect this product only to a grounding type receptacle  
protected by a ground-fault circuit interrupter (GFCI) or residual current device  
(RCD). Contact a qualified electrician if you cannot verify that the receptacle is  
protected by a GFCI/RCD. Use a qualified electrician to install the GFCI/RCD,  
which has a maximum rate of 30mA. Do not use a portable residual current device  
(PRCD).  
• Do not bury electrical cord. Locate cord where it will not be damaged by lawn  
mowers, hedge trimmers, and other equipment.  
• The supply cord cannot be replaced. If the cord is damaged the appliance should  
be scrapped.  
To reduce the risk of electric shock, do not use extension cords, timers, plug  
adaptors or converter plugs to connect unit to electric supply; provide a properly  
located outlet.  
• Assembly and disassembly by adults only.  
• Do not attempt to plug in or unplug this product while standing in water or when  
your hands are wet.  
• Position this product away from pool to prevent a child from climbing on pump to  
access the pool.  
• Children must stay away from this product and electrical cord(s).  
• Do not operate this product when pool is occupied.  
• Always unplug this product from the electrical outlet before removing, cleaning,  
servicing or making any adjustment to the product.  
• This product is for use with storable pools only. Do not use with permanently  
installed pools. A storable pool is constructed so that it may be readily  
disassembled for storage and reassembled to its original configuration.  
• Keep this product more than 2m away from the pool. (for France only).  
• Keep the plug of this product more than 3.5m away from the pool.  
• The plug shall be accessible after product installed.  
• This product is intended to be used only for the purposes described in the manual!  
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN  
PROPERTY DAMAGE, ELECTRIC SHOCK, ENTANGLEMENT OR  
OTHER SERIOUS INJURY OR DEATH.  
These product warnings, instructions and safety rules provided with the product represent  
some common risks of water recreation devices and do not cover all instances of risk and  
danger. Please use common sense and good judgement when enjoying any water activity.  
Page 3  
SAVE THESE INSTRUCTIONS  
 
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007  
106  
PARTS LIST  
1
4
7
2
5
8
3
6
9
NOTE: Drawings for illustration purpose only. May not reflect actual product. Not to  
scale.  
Page 4  
SAVE THESE INSTRUCTIONS  
 
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007  
106  
PARTS REFERENCE  
Before assembling your product, please take a few minutes to check the contents  
and become familiar with all the parts.  
1
2
3
4
6
5
7
8
9
NOTE: Drawings for illustration purpose only. May not reflect actual product. Not to scale.  
DESCRIPTION  
AIR RELEASE VALVE  
REF. NO.  
QTY.  
SPARE PART NO.  
10460  
1
2
3
4
5
6
7
8
9
1
1
1
1
1
2
2
4
2
VALVE O-RING  
THREADED COVER  
COVER SEAL  
10264  
10459  
10325  
FILTER CARTRIDGE (59900)  
STRAINER  
10120  
10399  
10122  
10134  
HOSE  
HOSE CLAMP  
HOSE SEAL  
When ordering parts, be sure to quote the model number and part numbers.  
Page 5  
SAVE THESE INSTRUCTIONS  
 
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007  
106  
SET-UP INSTRUCTIONS  
Be sure you have access to water to fill the pool and chemicals for the water. A  
small coin can be used to tighten the hose clamps (8).  
IMPORTANT:This filter pump is shipped with the air release valve (1) open  
(open the air release valve if necessary). DO NOT replace the air release valve  
until you reach STEP #8. Failure to follow these instructions will result in air  
trapped inside filter housing; the motor will run dry, be noisy and  
malfunction.  
1. Assemble above-ground-pool first. Carefully follow the pool’s installation  
instructions.  
2. Place the Filter-Pump the length of the hose away from the pool wall where the  
lower black protruding hose connection is "sticking-out".  
3. Remove wall plugs and then insert the strainers (6) into each of the protruding  
hose connections. The hoses (7) fit over the strainers inserted into the  
connections.  
4. There are two hoses to be connected to the Filter-Pump hose connections.  
With hose clamps (8), fasten one of the hoses (7) to the lower protruding hose  
connection (marked "+" on the pool liner) and to the pump connection (marked  
"+").  
5. Connect the second hose to the remaining upper protruding hose connection  
and to the lower pump connection. Make sure all the hose clamps (8) are tight.  
6. Twist the Filter-Pump’s threaded cover (3) in a clock-wise direction to be sure it  
is on "tight". Use only your hands to tighten the top. Do not tighten with tools  
such as pliers.  
7. Fill the pool to a level of at least 1-2 inches above the top connection. The  
water will automatically flow down into the pump.  
8. When water starts flowing out of the air release valve hole, screw in the air  
release valve back into the filter housing cover. Do not over tighten the valve.  
NOTE: Venting the system is necessary for air to escape as the filter  
housing fills with water.  
9. Connect the filter pump to the power outlet. The filter pump is now filtering the  
water.  
WARNING  
Risk of electric shock. Connect this product only to a grounding  
type receptacle protected by a ground-fault circuit interrupter  
(GFCI) or residual current device (RCD). Contact a qualified  
electrician if you cannot verify that the receptacle is protected by a  
GFCI/RCD. Use a qualified electrician to install the GFCI/RCD,  
which has a maximum rate of 30mA. Do not use a portable residual  
current device (PRCD).  
10. Operate the filter pump until the desired water clarity is obtained.  
Page 6  
SAVE THESE INSTRUCTIONS  
 
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007  
106  
SET-UP INSTRUCTIONS (continued)  
WARNING  
Position this product away from pool to prevent a child from  
climbing the pool.  
To inspect and change the filter cartridge, disconnect line cord, unscrew the  
strainer grids (6) from the strainer connectors and insert the hat-like plugs into the  
strainer connectors before servicing the filter. After service, open the air release  
valve, remove the plugs, allow any air to escape through the valve before tightening  
the valve again and replace the strainer grids. The pump is now primed with water  
again and may be turned on.  
WATER LEVEL  
UPPER PROTRUDING  
HOSE CONNECTION  
AIR RELEASE  
VALVE  
THREADED  
COVER  
PLUG  
HOSE  
STRAINER  
FILTER  
CARTRIDGE  
INSIDE  
UPPER PUMP  
CONNECTION  
INSIDE OF POOL  
BOTTOM PUMP  
CONNECTION  
HOSE  
CLAMP  
(ILLUSTRATION NOT TO SCALE)  
Page 7  
SAVE THESE INSTRUCTIONS  
 
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007  
106  
FILTER PUMP STATIONARY MOUNTING OPTION  
There are three mounting holes located at the bottom of the filter-pump base.  
These holes are provided because various country’s regulations, especially in the  
European community, require the filter-pump to be secured to the ground or to a  
base in a permanent upright position.  
These three holes form a triangle pattern and are 145mm from each other. The  
holes are slotted with a 7mm width.  
The filter-pump can be mounted on a cement base or onto a wooden structure to  
prevent accidental falling over. Total assembly must exceed 18kg. The drawings on  
the following show two possible ways of upright mounting. The European norm  
EN 60335-2-41 requires this product be secured to the ground or to a base.  
145mm  
145mm  
145mm  
145mm  
145mm  
-- (3) x M6 HEXAGON LOCK-NUTS  
-- (3) x M6 HEXAGON HEAD BOLTS  
Page 8  
SAVE THESE INSTRUCTIONS  
 
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007  
106  
FILTER CARTRIDGE CLEANING OR REPLACEMENT  
It is recommended that the filter cartridge be replaced at least  
every 2 weeks.  
1. Make sure filter pump is not operating. Disconnect line cord.  
2. To prevent water from escaping the pool, unscrew the strainer grids from the  
strainer connectors and insert the hat-like plugs into the strainer connectors.  
3. In a counter-clockwise motion, remove threaded cover (3) and cover seal (4).  
Be careful not to lose the cover seal (4).  
4. Remove filter cartridge (5) to clean it. The filter may be cleaned from the spray  
from a water hose.  
5. Use judgement as to whether cartridge needs to be replaced.  
6. Return cartridge to filtering position.  
7. Return the seal (4) and threaded cover (3) to their original positions. Tighten  
the threaded cover (3) by hand only, twisting it in a clock-wise direction.  
8. After service, open the air release valve, remove the plugs, allow any air to  
escape through the valve before tightening the valve again and replace the  
strainer grids. The pump is now primed with water again and may be turned on.  
Page 9  
SAVE THESE INSTRUCTIONS  
 
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007  
106  
POOL CARE AND CHEMICALS  
All pools require care to keep the water clear and hygienically clean. With  
proper chemical control, your filter will help attain this objective. Consult your  
pool supply dealer for instructions regarding the proper use of chlorine,  
algaecide and other chemical agents required for sparkling clear water.  
Keep pool chemicals away from children.  
Do not replenish chemicals in pool while pool is occupied. Skin or eye irritations  
could occur.  
Daily pH checking and chemical treatment of the water is very important and  
can not be overemphasized. Chlorine, algaecide and maintenance of proper pH  
levels are required when filling the pool as well as during the season. Consult  
your local swimming pool supply store for instructions.  
The season's first filling of the pool may have brackish water requiring extra  
water additives and extra filter changes. Do not allow swimming in pool until the  
pH level is balanced. Consult your local swimming pool supply store for  
instructions.  
Keep spare filter cartridges on hand. Replace cartridges every two weeks.  
Chlorinated water may damage lawns, gardens or shrubbery as children play  
in the pool and splash water outside the pool. Lawn areas underneath the  
pool liner will be destroyed. Note that some types of grass may grow through  
the liner but function is not affected.  
Filter run time depends on pool size, weather and usage level. Experiment with  
various run times so as to produce clean clear water.  
CAUTION  
Concentrated chlorine solutions may damage the pool liner. Always  
follow the chemical manufacturer’s directions, and the health and hazard  
warnings.  
LONG TERM STORAGE  
1. Before emptying your pool for long term storage, or relocation, be sure the  
water is directed towards an acceptable drain water receptacle away from the  
house. Check local regulations for specific directions regarding disposal of  
swimming pool water.  
2. After pool is empty of all water, disconnect all pool hoses (7) from pool and  
filter pump, simply reverse the set up instructions.  
3. Remove filter cartridge as shown in the Filter Cartridge Cleaning section,  
steps 2 thru 4.  
4. Remove the strainers (6) from the pool wall. Place the wall plugs into the hose  
connections. Loosen clamps (8) securing the strainers before removal.  
5. Drain water from the filter pump housing.  
6. Depending on the cartridge (5) usage, a new cartridge may be needed for next  
season, keep a spare available.  
7. Cover the seal (4), air release valve O-ring (2) and hose seals (9) with  
petroleum jelly to preserve its resilience during storage.  
8. Store the filter pump and accessories in a dry, cool storage location.  
9. The original packing carton can be used for storage.  
Page 10  
SAVE THESE INSTRUCTIONS  
 
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007  
106  
TROUBLESHOOTING GUIDE  
TROUBLE  
CHECK  
POSSIBLE SOLUTIONS  
FILTER MOTOR  
FAILS TO START  
• Not plugged in.  
Filter cord must be plugged into a 3 wire  
outlet that is protected by a Class A  
Ground Fault Circuit Interrupter, or RCD.  
• Fuse box needs checking.  
• GFCI/RCD circuit breaker  
tripped.  
• Reset circuit breaker. If circuit breaker  
trips repeatedly, your electrical system  
may have a defect. Turn off circuit  
breaker and call an electrician to  
correct the problem.  
• Motor too hot and overload protection  
shut motor off. Let motor cool down.  
FILTER DOESN’T  
CLEAN POOL  
• Improper chlorine or pH  
levels.  
• Filter cartridge dirty.  
• Cartridge damaged.  
• Excessively dirty pool.  
• Strainer screen restricting  
flow.  
Adjust chlorine and pH level. Consult  
your local swimming pool supply stores.  
• Clean or replace cartridge.  
• Check for holes in cartridge. Replace  
if damaged.  
• Operate filter for longer periods.  
• Clean strainer screen at pool wall inlet.  
FILTER DOESN’T  
PUMP WATER OR  
FLOW IS VERY  
SLOW  
• Inlet/discharge clogged.  
• Air leak on intake line.  
• Scale or buildup on cartridge.  
• Excessively dirty pool.  
• Filter cartridge dirty.  
• Look for obstructions in intake hose or  
discharge hose inside pool wall.  
• Tighten hose clamps, check hoses for  
damage, check pool water level.  
• Replace cartridge.  
• Clean cartridge more often.  
PUMP DOESN’T  
WORK  
• Low water level.  
• Fill pool to correct water level.  
• Clean strainer screens at pool inlet.  
• Tighten hose clamps, check hose for  
damage.  
• Check & clear any sticks or leaves in  
intake to pump.  
• Strainer screen plugged up.  
• Air leak on intake hose.  
• Faulty motor or impeller  
jammed.  
• Air lock inside cartridge  
chamber.  
• Open release valve at top of pump.  
TOP COVER  
LEAKING  
• O-ring missing.  
• Cover not tight.  
• Filter cartridge dirty.  
• Remove cover & check for O-ring.  
• Tighten cover (Manually).  
• Replace or clean cartridge.  
HOSE LEAKING  
AIR LOCK  
• Hose clamps.  
• Tighten/change hose clamps.  
• Pump housing and inlet hose  
air trapped.  
• Open air release valve, lift and lower  
the inlet hose until water starts to flow  
out of the air release valve, close air  
release valve.  
• The white inserts at both ends of the hoses shall remain inside and  
shall be firmly inserted in the hose. Do not remove the white inserts  
from the hoses. These white inserts are not serviceable parts.  
To facilitate the connection of the hoses into the black protruding hose  
connectors on the pool wall, you may use soapy water solution (mix 6  
drops of dish detergent in 1/2 a cup of water) to lubricate the inserts  
by simply dipping the hose ends into the solution. Continue per  
owner’s manual.  
HOSE  
INSERT  
• Do not use lubricants such as machine or industrial oil or grease.  
Page 11  
SAVE THESE INSTRUCTIONS  
 
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007  
106  
COMMON POOL PROBLEMS  
PROBLEM  
DESCRIPTION  
CAUSE  
REMEDY  
ALGAE  
• Greenish water.  
• Green or black  
spots on pool liner.  
• Pool liner is  
• Chlorine and pH levels • Super chlorinate with shock  
need adjustment.  
treatment. Correct pH to your  
pool store's recommended  
level.  
slippery and/or has  
a bad odor.  
• Vacuum pool bottom.  
• Maintain proper chlorine  
level.  
COLORED  
WATER  
• Water turns blue,  
brown, or black  
when first treated  
with chlorine.  
• Copper, iron or  
maganese in water  
being oxidized by the  
added chlorine.  
Common.  
• Adjust pH to recommended  
level.  
• Run filter until water is clear.  
• Clean cartridge frequently.  
SUSPENDED  
MATTER IN  
WATER  
• Water is cloudy or  
milky.  
• "Hard water" caused  
by pH level being too  
high.  
• Chlorine content is low.  
• Foreign matter in  
water.  
• Correct pH. Check with pool  
dealer for water treatment.  
• Check for proper chlorine  
level.  
• Clean or replace your filter.  
CHRONIC  
LOW WATER  
LEVEL  
• Level is lower than  
on previous day.  
• Rip or hole in pool  
liner or hoses. Tighten  
caps.  
• Repair with patch kit.  
• Finger tighten all caps.  
SEDIMENT  
ON POOL  
BOTTOM  
• Dirt or sand on  
pool floor.  
• Heavy use, getting in  
and out of pool.  
• Use Intex pool vacuum to  
clean bottom of pool.  
SURFACE  
DEBRIS  
• Leaves, insects  
etc.  
• Pool too close to  
trees.  
• Use Intex pool skimmer.  
IMPORTANT  
If you continue to experience difficulty, please contact our  
Consumer Service Department for assistance. See back cover for  
contact information.  
Page 12  
SAVE THESE INSTRUCTIONS  
 
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007  
106  
GENERAL AQUATIC SAFETY  
Water recreation is both fun and therapeutic. However, it involves  
inherent risks of injury and death. To reduce your risk of injury, read  
and follow all product, package and package insert warnings and  
instructions. Remember, however, that product warnings, instructions  
and safety guidelines cover some common risks of water recreation,  
but do not cover all instances or risk and or danger.  
For additional safeguards, also familiarize yourself with the following  
general guidelines as well as guidelines provided by nationally  
recognized Safety Organizations:  
• Demand constant supervision.  
• Learn to swim.  
Take the time to learn CPR and first aid.  
• Instruct anyone who is watching your children about potential pool  
hazards and about the use of protective devices such as locked doors,  
barriers, etc.  
Teach children what to do in case of an emergency.  
• Always use common sense and good judgement when enjoying any  
water activity.  
• Supervise, Supervise, Supervise.  
Page 13  
SAVE THESE INSTRUCTIONS  
 
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007  
106  
LIMITED WARRANTY  
PARTS LIST  
Your Krystal Clear™ Filter-Pump has been manufactured using the highest quality  
materials and workmanship. All Intex products have been inspected and found free of  
defects prior to leaving the factory. This Limited Warranty applies only to the Krystal  
Clear™ Filter-Pump.  
The provisions of this Limited Warranty apply only to the original purchaser and is not  
transferable. This Limited Warranty is valid for a period of one (1) year from the date of the  
initial retail purchase. Keep your original sales receipt with this manual, as proof of  
purchase will be required and must accompany warranty claims or the Limited Warranty is  
invalid.  
If a manufacturing defect is found within this one (1) year period, please contact the  
appropriate Intex Service Center listed in this manual. The Service Center will determine  
the validity of the claim.  
IMPLIED WARRANTIES ARE LIMITED TO THE TERMS OF THIS WARRANTY AND IN  
NO EVENT SHALL INTEX, THEIR AUTHORIZED AGENTS OR EMPLOYEES BE LIABLE  
TO THE BUYER OR ANY OTHER PARTY FOR DIRECT OR CONSEQUENTIAL  
DAMAGES OR LIABILITIES.  
This Limited Warranty does not apply if the Krystal Clear™ Filter-Pump is subject to  
negligence, abnormal use or operation, accident, improper operation, improper voltage or  
current contrary to operating instructions, or to damage by circumstances beyond Intex’s  
control, including but not limited to, ordinary wear and tear and damage caused by  
exposure to fire, flood, freezing, rain, or other external environmental forces. This Limited  
Warranty applies only to those parts and components sold by Intex. The Limited Warranty  
does not cover unauthorized alterations, repairs or disassembly by anyone other than Intex  
Service Center personnel.  
The costs associated with the loss of pool water, chemicals or water damage are not  
covered by this warranty. Injury or damage to any property or person is not covered by this  
warranty.  
Page 14  
SAVE THESE INSTRUCTIONS  
 
(106) MODEL 638 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/29/2007  
106  
For service questions or to order replacement parts, please contact the appropriate office  
questions.  
AREAS  
LOCATION  
AREAS  
LOCATION  
COMEXA S.A  
SAN IGNACIO 0201, PARQUE  
INDUSTRIAL PORTEZUELO,  
QUILICURA, SANTIAGO, CHILE  
TEL: 56-2-339 9000  
CHILE / ARGENTINA /  
PERU / URUGUAY  
ASIA  
INTEX DEVELOPMENT CO. LTD.  
8TH FLOOR,  
DAH SING FINANCIAL CENTRE,  
108 GLOUCESTER ROAD,  
WANCHAI, HONG KONG  
TEL: 852-28270000  
FAX: 56-2-339 9022  
FAX: 852-23118200  
SAUDI ARABIAN MARKETING &  
AGENCIES CO. LTD.  
PRINCE AMIR MAJED STREET,  
AL-SAFA DISTRICT. JEDDAH,  
KINGDOM OF SAUDI ARABIA  
TEL: 966-2-693 8496  
INTEX TRADING B.V.  
POSTBUS 1075, 4700 BB ROOSENDAAL,  
THE NETHERLANDS  
TEL: 31-(0)165-593939  
SAUDI ARABIA  
EUROPE  
FRANCE  
GERMANY  
ITALY  
FAX: 31-(0)165-593969  
FAX: 966-2-271 4084  
INTEX SERVICE (FRANCE) SAS  
52, ROUTE NATIONALE  
39190 BEAUFORT, FRANCE  
TEL: 08 90 71 20 39 (0.15 TTC/min)  
FAX: 03 84 25 18 09  
STEINBACH GMBH GERMANY  
AN DER WELLE 4  
60322 FRANKFURT  
STEINBACH GMBH AUSTRIA  
AISTINGERSTRAßE 2  
4311 SCHWERTBERG  
TEL: 0800 468397665  
FAX: 07262 61439-0  
INTEX TRADING S.R.O.  
BENESOVSKA 23,  
101 00 PRAHA 10  
CZECH REPUBLIC  
TEL: 420-2-717 32247  
FAX: 420-2-673 12552  
N.V. NICOTOY S.A.  
AUSTRIA  
CZECH REPUBLIC /  
EASTERN EUROPE  
TEL: 0800 468397665  
FAX: 07262 61439-0  
A & A MARKETING SERVICE  
OFFICE: VIA DEI MESTIERI 8, 20049  
CONCOREZZO, MILANO - ITALY  
TEL: 39-039-6886260  
BELGIUM  
DENMARK  
MOESKROENSESTEENWEG 383 C,  
8511 AALBEKE  
TEL: 0800 92088  
FAX: 39-039-6043603  
WAREHOUSE: C/O ALVI, VIALE DELLA  
REPUBBLICA 10 - 27100 PAVIA - ITALY  
TOY BROKERS LTD  
MARKETING HOUSE,  
BLACKSTONE ROAD  
HUNTINGDON, CAMBS.  
PE29 6EF. UK  
TEL: 01480 414361  
FAX: 32-56.20.37.61  
K.E. MATHIASEN A/S  
SINTRUPVEJ 12  
DK-8220 BRABRAND  
DENMARK  
TEL: +45 89 44 22 00  
FAX: +45 86 24 02 39  
LEKSAM AB  
BRANDSVIGSGATAN 6,  
S-262 73 ÄNGELHOLM,  
SWEDEN  
TEL: +46 431 44 41 20  
FAX: +46 431 190 35  
NORSTAR AS  
PINDSLEVEIEN 1  
N-3221 SANDEFJORD  
NORWAY  
TEL: +47 33 48 74 10  
UK  
FAX: 01480 414761  
SWEDEN  
NORWAY  
FINLAND  
RUSSIA  
GWM AGENCY  
GARTEN-U. WOHNMÖBEL  
RÄFFELSTRASSE 25  
POSTFACH  
CH-8045 ZURICH/SWITZERLAND  
TEL: + 41 - (0)900 - 455 456  
FAX: 41 44 455 50 65  
KOKIDO BVI LIMITED  
C/PLOMO 5-7, NAVE 19 POLÍGONO  
INDUSTRIAL AIMAYR SAN MARTÍN DE  
LA VEGA 28330 MADRID SPAIN  
TEL: 34-90-2351045  
SWITZERLAND  
SPAIN / PORTUGAL  
FAX: +47 33 48 74 11  
NORSTAR OY  
RUUKINTIE 20  
FIN-02330 ESPOO  
FINLAND  
TEL: +358 9 8190 530  
FAX: +358 9 8190 5335  
LLC BAUER  
KIEVSKAYA STR., 20,  
121165 MOSCOW, RUSSIA  
TEL: 095-249-9400/8626/9802  
FAX: 095-742-8192  
KATHAY HASTER  
UL. LUTYCKA 3,  
60-415 POZNAN  
TEL: +48 61 8498 381/380  
FAX: +48 61 8474 487  
RECONTRA LTD.  
H-1113 BUDAPEST, DARÓCZI ÚT 1-3,  
HUNGARY  
FAX: 34-91-6912709  
HUNTER OVERSEAS PTY LTD  
LEVEL 1, 225 BAY STREET,  
BRIGHTON, VICTORIA  
AUSTRALIA  
AUSTRALIA  
TEL: 61-3-9596-2144 or 1800-224-094  
FAX: 61-3-9596-2188  
HAKA NEW ZEALAND LIMITED  
UNIT 5, SENTINEL PARK,  
25 AIRBORNE ROAD, ALBANY  
PO BOX 302171,  
NORTH HARBOUR,  
AUCKLAND 1330  
NEW ZEALAND  
TEL: 649-4159213  
FAX: 649-4159212  
FIRST GROUP TRADING  
AL MOOSA GROUP BUILDING, 1ST  
FLOOR, OFFICE 102 & 103, UMM HURAIR  
ROAD, KARAMA, DUBAI, UAE  
TEL: 00971-4-3373322  
NEW ZEALAND  
POLAND  
HUNGARY  
BRAZIL  
MIDDLE EAST  
REGION  
TEL: +361 372 5200/113  
FAX: +361 209 2634  
KONESUL MARKETING & SALES LTDA  
RUA INÁCIO BORBA, 835 - CEP. 04715-020,  
CHÁCARA SANTO ANTONIO - SÃO  
PAULO - SP - BRASIL  
TEL: 55 (11) 5183 8866  
FAX: 55 (11) 5183 8866  
FAX: 00971-4-3375115  
WOOD & HYDE  
15-17 PACKER AVENUE, INDUSTRIA 2,  
CAPE TOWN, SOUTH AFRICA 7460  
TEL: 27-21-0800-204-692  
FAX: 27-21-505-5600  
SOUTH AFRICA  
Page 15  
SAVE THESE INSTRUCTIONS  
 

Ingersoll Rand Fitness Equipment MHD56298 User Manual
Insignia Speaker NS HT51 User Manual
Intellinet Network Solutions Digital Camera 510486 User Manual
Jasco Network Card 99000 User Manual
JBL Portable Speaker CS600SAT User Manual
Jenn Air Convection Oven JJW9527 User Manual
John Deere Automobile 772A User Manual
JVC Camcorder Accessories CB A260 User Manual
KitchenAid Dishwasher KUDC24SE User Manual
Klipsch Speaker Quintet III User Manual