Insignia Stereo System NS R5101HD User Manual

Quick Setup Guide I NS-R5101HD 5.1 Receiver  
1 Install remote control batteries  
Congratulations on your purchase of  
a high-quality Insignia product. Your  
5.1-channel surround sound receiver  
is designed for reliable and trouble-  
free performance.  
Remove the cover from the back of the remote control, insert the batteries  
as indicated in the battery compartment, then replace the cover.  
2 Connect speakers  
Position speakers around your room and connect as shown.  
Loosen cap, insert speaker wire into the side, then tighten cap.  
Use this guide for initial setup of your  
receiver. If you have questions, see  
your User Guide for more information.  
Front  
right  
Front  
left  
Center  
Package contents  
• Remote control  
• AAA batteries  
• FM antenna  
• AM loop antenna  
• Microphone for auto setup  
• Quick Setup Guide  
• User Guide  
Power amplifier  
Surround back  
speakers  
Powered subwoofer  
1
2
3
4
TV or screen  
5
6
7
8
Front right speaker  
Front left speaker  
Subwoofer  
Surround back left speaker  
Surround back right speaker  
Listening position  
Center speaker  
AAA batteries  
Surround Surround  
right left  
Microphone  
3 Connect devices  
You can connect headphones and one device, such as game console or video camera, to the front of your NS-R5101 receiver.  
Remote  
control  
ON/STANDBY  
Press to turn on your receiver  
or put it in standby mode  
during normal operation.  
Speaker On/Off  
Input Selector  
Press to turn off speakers  
when using headphones or  
TV speakers.  
Turn the knob to switch  
between components such  
as tuner, DVD, CD, or TV.  
Volume  
FM antenna  
AM loop antenna  
Power  
Press to turn off main power before  
connecting components.  
Video 3 Input  
Tuning/Preset  
Connect a game console  
or video camera here.  
Press TUNING buttons to choose an AM  
or FM radio station. Press PRESET buttons  
to choose a saved station.  
BAND  
Press to select  
the radio band,  
FM, FM-MONO,  
or AM.  
Headphone Jack  
 
Connecting a TV  
Connecting a Blu-ray Disc player or DVD player  
To connect a TV using HDMI (Best):  
• Connect an HDMI cable to the  
HDMI OUT jack on the back of  
your receiver and to the HDMI IN  
jack on the TV.  
To connect a Blu-ray Disc player or DVD  
player using HDMI (Best):  
To connect a Blu-ray Disc player or DVD player  
using component video (Better):  
To connect a Blu-ray Disc player or DVD player  
using standard (composite) video (Good):  
1 Connect a standard video cable to the VIDEO  
DVD IN jack on the back of your receiver and  
to the VIDEO OUT jack on the player.  
• Connect an HDMI cable to the HDMI IN DVD  
jack on the back of your receiver and to the  
HDMI OUT jack on the player.  
1 Connect a component video cable to the  
COMPONENT VIDEO IN 1 (DVD) jacks on the  
back of your receiver and to the COMPONENT  
VIDEO OUT jacks on the player.  
NOTE: An HDMI cable carries both video and audio. You do  
not need to make an audio connection.  
Blu-Ray Disc player  
or DVD player  
Blu-Ray Disc player  
or DVD player  
Blu-Ray Disc player  
or DVD player  
To connect a TV using component video (Better):  
Connect a component video cable to the COMPONENT VIDEO  
OUT jacks on the back of your receiver and to the COMPONENT  
VIDEO IN jacks on the TV.  
2 Connect an audio cable to the DVD IN AUDIO L/R  
jacks on the back of your receiver and to the AUDIO  
OUT jacks on the player. Or use digital (noted  
below) for better Audio experience.  
2 Connect an audio cable to the AUDIO IN DVD  
jacks on the back of your receiver and to the  
AUDIO OUT jacks on the player. Or use digital  
(noted below) for better Audio experience.  
NOTE: An HDMI cable carries both video and audio.  
You do not need to make an audio connection.  
Connecting a Cable TV or Satellite Box  
To connect a TV using standard (composite) video (Good):  
Connect a standard (composite) video cable to the MONITOR OUT  
jack on the back of your receiver and to the VIDEO IN jack on the TV.  
To connect a cable or satellite box using  
CABLE/SAT box using HDMI (Best):  
To connect a cable or satellite box using  
CABLE/SAT box using component video (Better):  
1 Connect a component video cable to the  
COMPONENT VIDEO IN 2 (CABLE/SAT) jacks  
on the back of your receiver and to the  
To connect a cable or satellite box using CABLE/  
SAT box using standard (composite) video (Good):  
1 Connect a standard video cable to the VIDEO  
CABLE/SAT IN jack on the back of your receiver  
and to the VIDEO OUT jack on the player.  
• Connect an HDMI cable to the HDMI IN  
CABLE/SAT jack on the back of your receiver  
and to the HDMI OUT jack on the player.  
COMPONENT VIDEO OUT jacks on the player.  
Blu-Ray Disc player  
or CABLE/SAT box  
Blu-Ray Disc player  
or CABLE/SAT box  
Blu-Ray Disc player  
or CABLE/SAT box  
To connect a TV to hear its sound through the receiver:  
Connect an audio cable to the TV IN AUDIO L/R jacks on the back of  
your receiver and to the AUDIO OUT jacks on the TV.  
NOTE: When viewing video program sources through MONITOR OUT jack, you must use the same type of video  
jacks that you did connect to video playback components such as Blu-ray Disc player, DVD player, or cable TV  
tuner.  
CABLE/  
SAT  
2 Connect an audio cable to the CABLE/SAT IN  
AUDIO L/R jacks on the back of your receiver  
and to the AUDIO OUT jacks on the player or use  
digital (noted below) for better Audio experience.  
2 Connect an audio cable to the AUDIO IN  
CABLE/SAT jacks on the back of your receiver  
and to the AUDIO OUT jacks on the player or use  
digital (noted below) for better Audio experience.  
NOTE: An HDMI cable carries both video and audio.  
You do not need to make an audio connection.  
Connecting a device to the front AV jacks  
To connect a device to the front  
AV jacks:  
1 Connect a standard (composite)  
video cable to the AUX 1 VIDEO  
jack on the front of your receiver  
and to a standard video device.  
Connecting digital audio  
To connect digital audio:  
1 Connect the video for a device to the CD, GAME/AUX2, DVD, or  
3 Press input selector button on the remote control (CD,  
GAME/AUX2, DVD, or CABLE/SAT) to select the video  
jack(s) the device is connected to, then press D.INPUTS  
one or more times to select the audio jack(s) the device  
is connected to. Each time you press D.INPUTS the  
audio source changes from O(ptical) 1, to O(ptical) 2, to  
CABLE/SAT video jack(s).  
2 Connect the digital audio for the device to a digital audio jack  
on the back of your receiver.  
• If the device has a coaxial digital audio jack, connect a 75Ω  
coaxial digital audio cable to the COAXIAL IN 1 (DVD) jack on  
the back of your receiver and to the COAXIAL OUT jack on the  
digital audio device.  
2 Connect an audio cable to the  
C(oaxial) 1, H(DMI), or A(nalog).  
AUX 1 L/R jacks on the front of  
your receiver and to the audio  
out jacks on the device.  
NOTE: If you press select CD, you cannot select HDMI as the audio source.  
NOTE: The default settings are as for the digital audio jacks are:  
OPTICAL IN 1 for devices connected to the video GAME/AUX 2 jack.  
OPTICAL IN 2 for devices connected to the video CABLE/SAT jack.  
COAXIAL IN 1 for devices connected to DVD video jack.  
Or,  
• If the device has an optical digital audio jack, connect an  
optical digital audio cable to the OPTICAL IN 1 (GAME/AUX2)  
or OPTICAL IN 2 (CABLE/SAT) jack on the back of your receiver  
and to the OPTICAL OUT jack on the digital audio device.  
 
4 Connect power  
5 Complete setup  
1. Connect the power cord to a power outlet.  
Press the input buttons on your remote control or rotate the INPUT SELECTOR knob on the  
front of your receiver to switch between devices. SeeSelecting the input sourcein your User  
Guide for more information.  
2. Press POWER on the front of your receiver.  
3. Press STANDBY/ON on the receiver or POWER ON on your remote control to turn on the receiver.  
Press the SOUND PARAMETER button on your remote control to adjust the sound  
parameter. SeeAdjusting sound parametersin your User Guide for more information.  
INPUT SELECTOR knob (receiver front)  
Input buttons (remote control)  
Adjust speaker settings with Auto Setup  
1. Connect the supplied microphone to the SETUP MIC jack  
NOTES:  
on the front of your receiver.  
Because the microphone for Auto Setup is designed for use with this receiver,  
do not use a microphone other than the one supplied with this receiver.  
After you have completed the auto setup procedure, disconnect the  
microphone.  
2. For best results, place the microphone close to the area in  
which you’ll be sitting.  
3. SeeSetting the listening environment (ROOM EQ)in your  
User Guide for more information on how to complete the  
auto speaker setup procedure.  
For additional help setting up your receiver, call (877) 467-4289.  
For information on using your receiver or for basic troubleshooting tips, see the Troubleshooting section in your User Guide.  
09-0363  
© 2009 Best Buy Enterprise Services, Inc. Distributed by Best Buy Purchasing, LLC 7601 Penn Avenue South, Richfield, MN USA 55423-3645 www.insigniaproducts.com  
 

Ingersoll Rand Sander R02 User Manual
Intel Computer Hardware SHG2 User Manual
Janome Sewing Machine 350E User Manual
JVC Car Speaker CS HX6947X User Manual
JVC Flat Panel Television GGT0220 001A H User Manual
JVC VCR HR A62U User Manual
Kenwood CD Player DP R892 User Manual
Kettler Fitness Equipment 07426 600 User Manual
KitchenAid Oven KCO1005 User Manual
Konica Minolta Copier IC 204 User Manual