™
CASCADE
™
INFINITY CASCADE SPEAKER SYSTEMS
Owner’s Guide
Model Five
Model Seven
Model Nine
Model Three V
Model Three C
Home Theater
PLACEMENT
For front-channel use, place one speaker on the left and another on the
right, along either side of the television monitor. Since the speakers are
magnetically shielded, you can place them near the TV without worrying
about the magnetic field distorting the TV picture.
Stereo
Before deciding where to place your Cascade speakers, survey your room
and think about placement, keeping the following points in mind and
using Figure 1 as a guide:
For surround-channel use, place speakers on bookshelves or stands
alongside the listening position. Final placement depends on room
acoustics, availability of space and your listening preference
(Figures 2 and 3).
• For best results, place the speakers 6' – 8' (1.5m – 2.5m) apart.
• Position each speaker so that the tweeter is approximately at ear level.
• Generally, bass output will increase as the speaker is moved closer to a
wall or corner.
In 6- or 7-channel configurations, place the rear channel(s) behind the
listening position, as shown in Figures 2 and 3.
• Refer to“Home Theater”if you also plan to use the speakers for home
theater reproduction.
NOTE: An Infinity powered subwoofer will add impact and realism to both
music and film soundtracks. Contact your Infinity dealer for recommenda-
tions on subwoofer models for your application.
Infinity Subwoofer
(optional)
Left
Front
Channel
Right
Left
Channel
Right
Channel
Front
Channel
Center
Channel
Listening Position
Couch
Figure 1. Experiment with speaker placement to obtain the best
bass level and stereo imaging in your room.
Left
Surround
Channel
Right
Surround
Channel
Left Rear
Channel
Center Rear
Channel
Right Rear
Channel
Figure 2.This overhead view shows a typical home theater plan.
Left/right rear channels are for a 7-channel system. Center
rear channel is for a 6-channel system.
(optional)
Right Rear
Channel
Left Rear
Channel
Center Rear
Channel
Figure 3.This figure shows an alternate layout, which may be
more suitable for some rooms. Left/right rear channels are for a
7-channel system. Center rear channel is for a 6-channel system.
3
CASCADE SPEAKER SYSTEMS
Model Nine and Model Seven
ASSEMBLY
1. Remove floor
It is strongly recommended that two people assemble the speakers
to minimize the possibility of damage or injury.
stand from carton.
2. Slide loud-
speaker onto
Installing Spiked Feet (Model Nine and Model Seven)
stand, making
sure the aligning
posts are lined up
with the receiver
terminal cup.
1. Open spike kit and locate the following items: feet (with spike/round
ends), four locking nuts, four nylon domes and one wrench.
2. Lay each stand on its side and locate the four threaded holes on the
bottom of the base.
3. For carpets, screw the round end of a foot into each hole and fully hand-
tighten a nut onto each one. For hard-surface floors, screw the spike end
into each hole instead and leave the rounded end exposed.
4. Carefully flip each base upright to sit on its feet.
5. If needed, adjust the feet so each speaker is level and then tighten each
nut with the enclosed wrench.To protect hard surfaces (e.g., wood floors),
slip a nylon dome onto each round end.
3. Insert #8 pan-
head screw into
rear of speaker to
secure to stand.
SEE DETAIL
A
Note: Spiked feet must be fully threaded into holes provided in the base
to ensure stability.
Locking Nut
DETAIL
A
5/8"
5/8" min.
1-1/8" max.
Foot
Round End
Spike End
Model Three V
Nylon Dome
(included for use
on wood floors)
1. Remove base from carton.
2. Securely fasten one cleat to
the middle set of holes
on the rear of the speaker
using two included
CARPETED
FLOORS
HARD-SURFACE
FLOORS
This cross section shows how to install the spikes onto the bottom of a
Cascade Model Nine and Model Seven.
1/4"-20 panhead screws.
3. Slide speaker with
cleat over the base.
+
+
Model Five
1. Remove base
from carton.
2. Securely fasten one cleat
to the set of holes above
the terminal using two
included 1/4"-20
panhead screws.
3. Slide speaker
with cleat over
the base.
+
+
4
CASCADE SPEAKER SYSTEMS
Attaching the Grilles
WALL-MOUNTING
The Cascade loudspeakers use a unique frameless grille. Each end of the
grille cloth contains a magnet. Simply curl the magnet assembly behind
the grille cloth, place one end of the grille just above the tweeter and
then gently pull the grille taut, attaching the other end of the grille just
below the woofer.
NOTE: The customer is responsible for the correct selection and use of
mounting hardware (available through hardware stores) that will ensure
the proper and safe wall-mounting of the speakers.
Model Three V, Model Three C, Model Five
1.Attach
wall bracket
to wall
at desired
location.
Model Three C
Model Five
Model Three V
2. Securely fasten the
two cleats to the rear
of the speaker, using
the outermost holes,
using two included
1/4"-20 panhead
screws per cleat.
+
+
3. Carefully slide the
cleats on the rear
of the speakers
over the tabs
of the wall
bracket.
wall
5
CASCADE SPEAKER SYSTEMS
WIRING THE SYSTEM
IMPORTANT: Make sure all equipment is turned off before making any
connections.
For speaker connections, use a high-quality speaker wire with polarity
coding.The side of the wire with a ridge or other coding is usually
considered positive polarity (i.e., +).
NOTE: If desired, consult your local Infinity dealer about speaker wire and
connection options.
To ensure proper polarity, connect each + terminal on the back of the
amplifier or receiver to the respective + (red) terminal on each speaker,
–
as shown in Figure 4. Connect the (black) terminals in a similar way.
See the owner’s guides that were included with your amplifier or receiver
and television to confirm connection procedures.
–
–
IMPORTANT: Do not reverse polarities (i.e., + to or to +) when
making connections. Doing so will cause poor imaging and diminished
bass response.
Figure 5.This example shows how to connect bare wires to the
terminals. Banana plugs may also be inserted directly into the rear
of the connector.
Figure 4.This figure shows how to connect bare wires to the terminals.
Figure 6.Wiring diagram shows polarity connections for one channel
of a stereo or home theater system.
6
CASCADE SPEAKER SYSTEMS
FINAL ADJUSTMENTS
BI-WIRING
Check the speakers for playback, first by setting the system volume con-
trol to a minimum level, and then by turning on the power of your audio
system. Play a favorite music or video segment and increase the system
volume control to a comfortable level.
The outer connection panel and internal dividing network of the Cascade
loudspeakers are designed so that separate sets of speaker cables can
be attached to the low-frequency transducer and midrange/high-
frequency transducer portions of this dividing network.This is called
bi-wiring. Bi-wiring can provide several sonic advantages and
considerably more flexibility in power amplifier selection.
NOTE: You should hear balanced audio reproduction across the entire
frequency spectrum. If not, check all wiring connections or consult
the authorized Infinity dealer from whom you purchased the system.
The amount of bass you hear and the stereo-image quality will be affected
by a number of different factors, including the room’s size and shape,
the construction materials used to build the room, the listener’s position
relative to the speakers, and the position of the speakers in the room.
Listen to a variety of music selections and note the bass level. If there is
too much bass, move the speakers away from nearby walls. Conversely, if
you place the speakers closer to the walls, there will be more bass output.
Nearby reflecting surfaces can adversely affect stereo-imaging quality. If
this happens, try angling the speakers slightly inward toward the listening
position until the optimum effect is achieved.
CARE OF YOUR SPEAKER SYSTEM
Each Cascade Series enclosure has a finish that does not require any
routine maintenance.When needed, use a soft cloth to remove any finger-
prints or dust from the enclosure.
Figure 7.
NOTE: Do not use any cleaning products or polishes on the cabinet
or grille.
Single-Stereo Amplifier
If a problem occurs, make sure that all connections are properly made
and clean. If a problem exists in one loudspeaker, reverse the connection
wires to the left and right system. If the problem remains in the same
speaker, then the fault is with the loudspeaker. If the problem appears in
the opposite speaker, the cause is in another component or cable. In the
event that your subwoofer ever needs service, contact your local Infinity
center near you.
IMPORTANT: Please attach your sales receipt to this manual and store it
in a safe place. In the event that your Infinity speaker requires warranty
service, you will need to provide your sales receipt.
Figure 8.
Dual-Stereo Amplifier
Figure 9.
7
CASCADE SPEAKER SYSTEMS
SPECIFICATIONS
Model Nine
Model Seven
Model Five
Frequency Response:
80Hz – 20kHz ( 3dB)
100Hz – 20kHz ( 3dB)
100Hz – 20kHz ( 3dB)
–
–
–
40kHz ( 6dB)
40kHz ( 6dB)
40kHz ( 6dB)
Recommended
Amplifier Power Range:
10 – 150 Watts
87dB
10 – 100 Watts
85dB
10 – 150 Watts
85dB
Sensitivity:
(2.83V @ 1 meter)
Nominal Impedance:
Crossover Frequency:
Mid-Bass Driver(s):
8 Ohms
8 Ohms
8 Ohms
1,500Hz; 24dB/octave
1,800Hz; 24dB/octave
1,800Hz; 12dB/octave
Dual 7-3/4" x 3-3/8"
(197mm x 85mm) CMMD®,
magnetically shielded
7-3/4" x 3-3/8"
7-3/4" x 3-3/8"
(197mm x 85mm) CMMD®,
magnetically shielded
(197mm x 85mm) CMMD®,
magnetically shielded
High-Frequency Driver:
1" (25mm) CMMD,
magnetically shielded
1" (25mm) CMMD,
magnetically shielded
1" (25mm) CMMD,
magnetically shielded
Dimensions (H x W x D):
(with grille)
47" x 10-1/2" x 11-1/2"
(1194mm x 267mm x 292mm)
47" x 10-1/2" x 11-1/2"
(1194mm x 267mm x 292mm)
22-1/2" x 5-1/2" x 5-1/2"
(572mm x 140mm x 140mm) Wall-mounted
30-1/4" x 7-3/4" x 8-1/2"
(768mm x 197mm x 216mm) On included base
Weight:
28.2 lb (12.8kg)
24.7 lb (11.2kg)
13.5 lb (6.1kg) Wall-mounted
20.5 lb (9.3kg) On included base
Model Three V
Model Three C
Frequency Response:
80Hz – 20kHz ( 3dB)
80Hz – 20kHz ( 3dB)
–
–
40kHz ( 6dB)
40kHz ( 6dB)
Recommended
Amplifier Power Range:
NA
10 – 150 Watts
87dB
Sensitivity:
87dB
(2.83V @ 1 meter)
Nominal Impedance:
Crossover Frequency:
Mid-Bass Driver(s):
8 Ohms
8 Ohms
1,500Hz; 24dB/octave
1,500kHz; 24dB/octave
Dual 7-3/4" x 3-3/8"
(197mm x 85mm) CMMD®,
magnetically shielded
Dual 7-3/4" x 3-3/8"
(197mm x 85mm) CMMD®,
magnetically shielded
High-Frequency Driver:
1" (25mm) CMMD,
magnetically shielded
1" (25mm) CMMD,
magnetically shielded
Declaration of Conformity
Dimensions (H x W x D):
(with grille)
30" x 5-1/2" x 5-1/2"
(762mm x 140mm 140mm) Wall-mounted
36-5/8" x 7-3/4" x 8-1/2"
5-1/2" x 30-3/4" x 6"
(140mm x 781mm x 152mm)
We, Harman Consumer Group International
2, route de Tours
(930mm x 197mm x 216mm) On included base
72500 Chateau du Loir
France
Weight:
18 lb (8.2kg) Wall-mounted
18 lb (8.2kg)
26 lb (11.8kg) On included base
declare in own responsibility that the products described
in this owner’s manual are in compliance with technical
standards:
Infinity continually strives to update and improve existing products, as well as create new ones.The specifications and
construction details in this and related Infinity publications are therefore subject to change without notice.
EN 61000-6-3:2001
EN 61000-6-1:2001
Laurent Rault
Harman Consumer Group International
Chateau du Loir, France 9/05
© 2005 Harman International Industries, Incorporated.All rights reserved.
Infinity Systems, 250 Crossways Park Drive,Woodbury, NY 11797 USA 516.674.4INF (4463) (USA only) www.infinitysystems.com
Infinity, Harman International and CMMD (patent nos. 6,327,372 and 6,404,897) are trademarks of Harman International Industries, Incorporated, registered in the United States and/or other countries.
Cascade, Maximum Radiating Surface and Constant Acoustic Impedance (patent pending) are trademarks of Harman International Industries, Incorporated.
Part No. 819001082001 8/05
|